Allegion 8310-818 User manual

75.5320.02 ALLEGION PUSH PLATES 20190305 Page 1 of 4
PUSH PLATES
75.5320.02 ALLEGION PUSH PLATES 20190305 Page 1 of 4
Stainless steel actuator switches
8310-818, -852, -853, -855, -856
ENGLISH
DESCRIPTION
ACCESSORIES
BOLLARDS BOXES TRANSMITTERS & RECEIVERS
433 MHz
JAMB
Logo: 8310-818
Text & Logo: 8310-818T
1.5” x 4.75” x 0.62”
4.75” SQUARE
Logo: 8310-853
Text & Logo: 8310-853T
Text & Alt. logo: 8310-853TA
4.75” x 4.75” x 0.62”
VESTIBULE
Text & Logo: 8310-855
4.75” × 4.75” × 0.62”
4.5” ROUND
Logo: 8310-856
Text & Logo: 8310-856T
4.5” x 0.62”
6” ROUND
Logo: 8310-852
Text & Logo: 8310-852T
Text & Alt. logo: 8310-852TA
6” x 0.62”

Page 2 of 4 75.5320.02 ALLEGION PUSH PLATES 20190305
Shut off all power going to header before attempting any wiring procedures.
Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected
reactions by the door.
ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling
any board, ensure you dissipate your body’s ESD charge.
Always check placement of all wiring before powering up to ensure that moving door parts will not catch any
wires and cause damage to equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be
performed by BEA, Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.
PRECAUTIONS
Page 2 of 4 75.5320.02 ALLEGION PUSH PLATES 20190305
READ BEFORE BEGINNING INSTALLATION/PROGRAMMING/SET-UP
Only trained and qualified
personnel are recommended
to install and set up the
sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Always test the
proper operation of
the installation before
leaving the premises.
The door control system
and the header cover
profile must be correctly
grounded.
MAINTENANCE
Clean the push plates using only a damp, non-abrasive cloth.
Regular cleaning with harsh solvents or abrasive materials may cause deterioration of the paint or
coating.

75.5320.02 ALLEGION PUSH PLATES 20190305 Page 3 of 4
75.5320.02 ALLEGION PUSH PLATES 20190305
75.5320.02 ALLEGION PUSH PLATES 20190305 Page 3 of 4
COM
NO
NC
SIDE VIEW
1
Wire the push plate to the door controller
or radio-controlled transmitter using the
NO and COM contacts.
A
A
A
A
B
B
2
Thread each hex-head screw 3⁄4of the way into the electrical enclosure. Leave about 1⁄2” of the screw
unthreaded.
The 6” and 4.75” push plates contain 2 sizes of screws:
larger screws = corner locations on 4×4 electrical type boxes (A above)
smaller screws = single-gang or double-gang electrical type boxes (B above)
NOTES:
If using any of the following, the plate/bracket/ring
must be installed before securing push plate to the
box:
• adapter plate (10BRINGC for double-gang
boxes and 50.5016 for vestibule plates)
• bracket (10PBRACKET or 10PBRACKETCA for
surface-mounting)
• weather ring (10WRSQ475, 10WRRND45,
10WRRND6)
3
Install the push plate onto the box, aligning the applicable key-
holes with the hex screws. Slide the push plate down, and then
secure the push plate to the box by tightening the screws using
the provided hex key.
4
Test for proper push-plate
activation.
PLEASE KEEP FOR FURTHER USE – DESIGNED FOR COLOR PRINTING
| Original Instructions
MOUNTING & WIRING

Page 4 of 4 75.5320.02 ALLEGION PUSH PLATES 20190305
©BEA | Original Instructions | PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING
Page 4 of 4 75.5320.02 ALLEGION PUSH PLATES 20190305
The sensor manufacturer cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore, the sensor
manufacturer does not guarantee any use of the sensor outside of its intended purpose.
The sensor manufacturer strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for
doors/gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor
system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107).
Verify that all appropriate industry signage and warning labels are in place.
INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
Do not leave problems unresolved. If a satisfactory solution cannot be achieved after
troubleshooting a problem, please contact Allegion at 1-877-671-7011. If you must wait for
the following workday to call Allegion, leave the door inoperable until satisfactory repairs can
be made. Never sacrifice the safe operation of the automatic door or gate for an incomplete
solution.
For more information, visit www.allegion.com.
WIRING DIAGRAM