Zamel exta WZM-01 Series User manual

TWILIGHT SWITCH WZM-01 INSTRUCTION MANUAL
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamel.com, e-mail: [email protected]
plik: inst_ext_gb_wzm-01 | modykacja: 03.08.2015
APPEARANCE
The device is designed for
one-phase installation and
must be installed in accordan-
ce with standards valid in a
particular country. The device
should be connected accor-
ding to the details included in
this instruction manual. Installation,connection
and control should be carried out by a quali-
ed electrician staff, who act in accordance
with the instruction manual and the device
functions. Disassembling of the device is equal
with a loss of guarantee and can cause elec-
tric shock. Before installation make sure the
connection cables are not under voltage. The
cruciform head screwdriver 3,5 mm should be
used to instal the device. Improper transport,
storage,and use of the device inuence its
wrong functioning. It is not advisable to instal
the device in the following cases: if any device’s
part is missing or the device is damaged or de-
formed. In case of improper functioning of the
device contact the producer.
CAUTION
FEATURES
TECHNICAL DATA
DESCRIPTION
WZM-01
Input terminals: L, N
Input rated voltage: 230 V AC
Input voltage tolerance: -15 ÷ +10 %
Nominal frequency: 50 / 60 Hz
Rated power consumption: 24 mA
Input rated indicator: LED green
Light sensor terminals: IN, IN
Maximum cable lenght: 50 m (MTY 2x 0,5 mm2)
Threshold adjustment range: 0 ÷ 200 lx (rotating potentiometer)
Relay indicator: LED red
Output contacts parameters: 1NO/NC - 16 A / 250 V AC1 4000 VA
Number of terminal clamps: 7 (WZM-01); 2 (SOS-01)
Section of connecting cables: 0,2 ÷ 2,50 mm2
Ambient temperature range: -20 ÷ +45 oC
Operating position: free
Mounting: TH rail 35 (PN-EN60715)
Casing protection degree: IP20
Protection level: II
Overvoltage category: II
Pollution degree: 2
Surge voltage: 1 kV (EN 61000-4-5)
Dimensions: monomodular (17,5 mm) 90 x 17,5 x 66 mm
Weight: 0,075 kg
Reference standards: EN 60669-1, EN 60669-2-1
EN 61000-4-2,3,4,5,6,11
● Receivers controll depending on illumi-
nous ux density
● Input rated indicator
● Relay indicator
● Smooth switch on threshold regulation
● Wide switch on threshold adjustment
range (from 0 to 200 Ix)
● system requires outer light intensity
sensor (e.g. SOH-01, SOH-03, SOH-
05, SOS-01)
● Resistant to momentary changes of illu-
minous ux density
● Switch threshold hysteresis
● Relay output – one switch contact of
maximum relay capacity 16A
The twilight switch WZM-01/SOS is
used to control lighting devices or other
energy receivers depending on illuminous
ux density. The system switches on the
lighting at dusk and switches off at dawn.
The switching on threshold can be
smoothly adjusted by the user. The sys-
tem is resistant to momentary changes of
illuminous ux density, which guarantees
reliability. External illuminous ux density
sensor transmits the signal to the twilight
switch WZM-01. Sensor connecting cable
of 50 m maximum lenght enables the sen-
sor to be put in a suitable place.
Input rated indicator
Input termianal (L) Input terminal (N)
Relay indicator
Output relay terminals
(11,12,14)
Lighting sensor input
terminals (IN, IN)
The symbol stands for selective
collection of electrical and
electronic devices.
Placing used devices with other
waste is not allowed
Switch on threshold
adjustment

MOUNTING, FUNCTIONING
1. Disconnect the power supply
2. By means of special equipment check
if there is no voltage on connection
cables
3. Install WZM-01 device in the switch-
board on TH-35 rail
4. Connect the cables with the terminals
according to installing diagram,
5. Switch on the power supply from the mains
6. Set the potentiometer of the threshold of
switch on the lighting to a minimum.
7. If the lighting outside reaches the level
at which the lighting installation is to be
switched on – turn delicately the poten-
tiometer in the direction of a maximum,
until it switches on
8. Leave the potentiometer in a set posi-
tion.
The system works properly after switching
on the power supply from the mains. Turning
the potentiometer in the direction of „ ” caus-
es the lighting device to switch on at lower
lighting level, in the direction of „
☼ ” causes
the device to switch on at higher lighting
level. In case the inner sensor’s illuminous
ux density falls below the preset threshold
the system switches on the output relay and
its lighting devices. The relay is switched on
until the illuminous ux density is over the
preset threshold. Using the illuminous ux
density hysteresis (Δ) and relay switching off
time delay (T) makes the system resistant to
momentary and accidental sensor lighting.
During installation attention should be paid
that switched on lighting will not disrupt the
functioning of the lighting sensor
CONNECTING
TIME COURSE
RELAY CAPACITY
INNER DIAGRAM
EXAMPLE OF INSTALATION
Illuminous
ux density 200 lx 35 lx 20 lx 2 lx
Potentiometer
position min. max.
☼
min. max.
☼
min. max.
☼
min. max.
☼
Typical application:
The twilight switch operates the lighting control functions (e.g garden lighting)
The lighting sensor should be installed in a place which is not directly illuminated by lights
that are operated by this twilight switch.
LIGHT SENSOR FAMILY
LIGHT
SENSOR
16,8
6,2
CASING DIMENSIONS
PRODUCT FAMILY
Twilight switch WZM-01/SOS belongs to the
WZx twilight switches family.
500 W
2000 W 1000 W
750 W
t
☼☼
t
∆
11,14
U
lx
T
t
Lp
∆ ≈ 5 ÷ 60 lx
T ≈ 30 s
SENSOR Lenght
SOH-01 1 m
SOH-03 3 m
SOH-05 5 m
SOS-01 no
Sensor type
Version
01 – one range
02 – two ranges
(only type M casing)
Type of casing
M – monomodular
N – surface mounting
H – hermetic
S - special
Symbol
WARRANTY CARD
There is 24 months guarantee on the product
1. ZAMEL Sp. z o.o. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions
a) mechanical damage during transport, loading / unloading or under other circumstances
b) damage caused by incorrect mounting or misuse of ZAMEL Sp. z o.o products
c) damage caused by unauthorised modications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer
3. The PURCHASER shall lay any claims on grounds of the garantee card in writing to the dealer or ZAMEL Sp. z o.o
4. ZAMEL Sp. z o.o is liable for processing any claim according to current Polish legislation
5. ZAMEL Sp. z o.o shall process the claim at its own discretion: product repair, replacement or money return
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this guarantee card.
Salesman stamp and signature, date of sale