EtherWAN EX48050-00B User manual

Hardened Web-Smart High Power PoE Ethernet Switch
Quick Start Guide
This quick start guide describes how to install and use the Hardened
Web-Smart High Power PoE (Power over Ethernet) Ethernet Switch. This is
the switch of choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
User’sManual 1

Hardened Web-Smart High Power PoE Ethernet Switch
LED State Indication
Steady Power on.
Power1
Power2
Power3 Off Power off.
Steady Power redundant system failure occurred.
Fault Off Power redundant system failure is not occurred.
10/100Base-TX, 100Base-FX/BX
Steady A valid network connection established.
Link/ACT
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Valid port connection at 100Mbps.
10/100 Off Valid port connection at 10Mbps.
Steady Powered Device (PD) is connected.
PoE Off Powered Device (PD) is disconnected.
Power Input Assignment
Power3 55VDC DC Jack
＋55VDC
Power2
－Power Ground
＋55VDC
Power1
－Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 24VDC
Relay Alarm Assignment
FAULT
*Warning signal disable for following:
The relay contact closes if Power1 and Power2 are
both failed but Power3 on.
The relay contact closes if Power3 is failed but
Power1 and Power2 are both on.
2 User’sManual

Hardened Web-Smart High Power PoE Ethernet Switch
The 10/100Base-TX and 100Base-FX/BX Connectors
The 10/100Base-TX Connections
The following lists the pinouts of
10/100Base-TX ports.
Pin PoE Ports (Port 1-4) Non-PoE Port (Port 5)
1 Output Transmit Data + Output Transmit Data +
2 Output Transmit Data - Output Transmit Data -
3 Input Receive Data + Input Receive Data +
4 Positive (VCC+)
5 Positive (VCC+)
6 Input Receive Data - Input Receive Data -
7 Negative (VCC-)
8 Negative (VCC-)
The 100Base-FX Connections
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive) port of
device II, and the Rx (receive) port of device I to the Tx (transmit) port of
device II.
The WDM 100Base-BX Connections
The fiber port pinouts
Only one optical fiber is required to transmit and receive data.
Functional Description
zMeets NEMA TS2 Environmental requirements such as temperature,
shock, and vibration for traffic control equipment.
zMeets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
zManageable via Web browser interface.
zPort 1 – 4 support Power over Ethernet (PoE) Power Sourcing
Equipment (PSE).
zHigh Power PoE design up to 30W.
zSupports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,
full/half-duplex. Auto MDI/MDIX.
z100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX:
WDM Multi mode/Single mode SC type.
User’sManual 3

Hardened Web-Smart High Power PoE Ethernet Switch
zSupports 1024 MAC addresses. Provides 512K bits memory buffer.
zAlarms for power and port link failure by relay output.
zPower Supply: Redundant 55VDC Terminal Block power inputs and
55VDC DC JACK with optional 100-240VAC external power supply.
zOperating voltage and Max. current consumption: 2.36A @ 55VDC.
Power consumption: 130W Max.
z-40℃to 75℃(-40℉to 167℉) operating temperature range. Tested for
functional operation @ -40℃to 85℃(-40℉to 185℉).
zSupports Wall and Desktop Mounting installation.
Web Configuration
zLogin the switch:
Specify the default IP address (192.168.1.10) of the switch in the web
browser. A login window will be shown as below:
4 User’sManual

Hardened Web-Smart High Power PoE Ethernet Switch
zEnter the factory default user name: admin.
Enter the factory default password: admin.
Then click on the “OK” button to log on to the switch.
User’sManual 5

Hardened Web-Smart High Power PoE Ethernet Switch
6 User’sManual
Preface
This manual describes how to install and use the Hardened
Web-Smart High Power PoE Ethernet Switch. This switch
introduced here is designed to deliver full scalability with
web-based management functions. Capable of operating at
temperature extremes of -40℃to +75℃, this is the switch of
choice for harsh environments constrained by space.
Port 1 to port 4 on this switch supports Power over Ethernet
(PoE) Power Sourcing Equipment (PSE) and can detect a
Powered Device (PD). Using external 55VDC power inputs
through Terminal Block or Power Jack, data and power can
be transmitted to a Powered Device (PD) over the same
twisted-pair Ethernet cable through port 1 to port 4 on the
switch.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Features on the Hardened Web-Smart High Power PoE Ethernet Switch
zIllustrative LED functions
zInstallation instructions
zManagement Configuration
zSpecifications

Hardened Web-Smart High Power PoE Ethernet Switch
User’sManual 7
Table of Contents
Quick Start Guide 1
PHYSICAL DESCRIPTION 1
The Port Status LEDs and Power Inputs 1
The 10/100Base-TX and 100Base-FX/BX Connectors 3
FUNCTIONAL DESCRIPTION 3
WEB CONFIGURATION 4
Preface 6
Table of Contents 7
Product Overview 9
HARDENED WEB-SMART HIGH POWER POEETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
SWITCH MANAGEMENT 12
Web-based browser interface 12
Installation 13
SELECTING A SITE FOR THE SWITCH 13
CONNECTING TO POWER 13
Redundant DC Terminal Block Power Inputs 13
55VDC DC Jack 14
Alarms for Power and Port Link Failure 14
CONNECTING TO YOUR NETWORK 15
Cable Type & Length 15
Cabling 15
Switch Management 17
MANAGEMENT ACCESS OVERVIEW 17
WEB MANAGEMENT 18
Web-Based Browser Management 19
LOGGING ON TO THE SWITCH 19
UNDERSTANDING THE BROWSER INTERFACE 21
ADMINISTRATOR 23
Authentication Configuration 23
System IP Configuration 24
System Status 25
Load Default Setting 26
Firmware Update 27
Reset Device 28
PORT MANAGEMENT 29

Hardened Web-Smart High Power PoE Ethernet Switch
8 User’sManual
Port Configuration 29
Bandwidth Control 30
Broadcast Storm Control 31
Max. Packet Length 32
Port Alarm Setting 33
VLAN SETTING 34
Multi to 1 Setting 34
Tag Based VLAN 35
Port Based VLAN 36
QOSSETTING 37
Class of Service Configuration 37
High Priority Queue Configuration 38
Customization Diffserv 39
POE 40
PoE System Settings 40
PoE Port Settings 41
PoE Scheduling 42
PORT SECURITY 44
CONFIGURATION BACKUP/RECOVERY 45
LOGOUT 46
Specifications 47

Hardened Web-Smart High Power PoE Ethernet Switch
Product Overview
Hardened Web-Smart High Power PoE Ethernet
Switch
Front and Back View
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
•The Hardened Web-Smart High Power PoE Ethernet Switch
•User’s Manual
User’sManual 9

Hardened Web-Smart High Power PoE Ethernet Switch
10 User’sManual
Product Highlights
Basic Features
zMeets NEMA TS2 Environmental requirements such as temperature,
shock, and vibration for traffic control equipment.
zMeets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
zManageable via Web browser interface.
zPort 1 – 4 support Power over Ethernet (PoE) Power Sourcing
Equipment (PSE).
zHigh Power PoE design up to 30W.
zSupports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,
full/half-duplex. Auto MDI/MDIX.
z100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX:
WDM Multi mode/Single mode SC type.
zSupports 1024 MAC addresses. Provides 512K bits memory buffer.
zAlarms for power and port link failure by relay output.
zPower Supply: Redundant 55VDC Terminal Block power inputs and
55VDC DC JACK with optional 100-240VAC external power supply.
zOperating voltage and Max. current consumption: 2.36A @ 55VDC.
Power consumption: 130W Max.
z-40℃to 75℃(-40℉to 167℉) operating temperature range. Tested for
functional operation @ -40℃to 85℃(-40℉to 185℉).
zSupports Wall and Desktop Mounting installation.