Allen-Bradley 140G-G-DRA User manual

DIN Mounting Adapter for 140G-G, 140G-H, 140G-I, 140G-J
Staffa per fissaggio su profilato DIN 50022
Montageclip für Befestigung auf DIN 50022 Hutschiene
Patte pour fixation sur profilé DIN 50022
Accesorio de fijación en perfil DIN 50022
Bul. 140G/140MG
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs.
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
Installation - Installazione - Instalación
Instalação - -
DIR 1000719R0820 Version 03 - 140G-G-DRA, 140G-G-DRA4, 140G-H-DRA, 140G-H-DRA4, 140G-I-DRA, 140G-I-DRA4, 140G-J-DRA, 140G-J-DRA4
xx lb-in
xx Nm
Required tools
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
0.18"/4.6mm
from 0.79" to 0.83"
from 20 mm to 21 mm
dia. 0.13"
ø 3.5 mm
140G-H, 140G-J
x2
x2
0.18"/4.6 mm
140G-G, 140G-I
LENGTH M
73 mm (2.87" ) M 4
LENGTH M
85 mm (3.35" ) M 4
DIR 1000719R0820 Version 03
x2
from 0.51" to 0.55"
from 13 mm to 14 mm
dia. 0.13"
ø 3.5 mm
CLACK
1
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。物
A B C D
E F G H
140G-G 3p 140G-G 4p 140G-H 3p 140G-H 4p
140G-I 3p 140G-I 4p 140G-J 3p 140G-J 4p
Supplied with the breaker
I
140G-J
0.18"/4.6mm
from 0.75" to 0.79"
from 19 mm to 20 mm
dia. 0.13"
ø 3.5 mm
x2
LENGTH M
80 mm (3.15") M 4

(2)
1
CD
GH
x2
140G-G
140G- I
DIR 1000719R0802 Version 03
140G-H
140G-J
3
A B
E F
140G-G
140G-H
140G- I
140G-J
2
9.7 lb-in
1.1 Nm
9.7 lb-in
1.1 Nm
0.18"/4.6mm
from 0.79" to 0.83"
from 20 mm to 21 mm
dia. 0.13"
ø 3.5 mm
140G-J Frame only
x2
LENGTH M
85 mm (3.35" ) M 4
I
140G-J Frame only

(3)
DIR 1000719R0802 Version 03
3
2
1
140G-G
140G-H
140G- I
140G-J
5
4
4
1
1

DISASSEMBLY
1
1
DIR 1000719R0820 Version 03 - ECN000132133
Copyright © 2020 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Publication 140G-IN154D-MU-P - April 2020
5140G-G
140G-H
140G- I
140G-J
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
Product certifications are located in the Rockwell Automation Literature Library:
http://www.rockwellautomation.com/global/literature-library/overview.page
Publication No: 140G-CT009
3
2
4