Allen-Bradley Kinetix 6200 User guide

Kinetix 6200 and Kinetix 6500
Safe Torque-off Multi-axis Servo Drives
Catalog Numbers 2094-SE02F-M00-S0, 2094-EN02D-M01-S0
Safety Reference Manual

Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety
Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from
your local Rockwell Automation® sales office or online at http://www.rockwellautomation.com/literature/) describes some
important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference,
and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the
use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Allen-Bradley, Kinetix, RSLogix, TechConnect, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
WARNING: Identifies information aboutpractices or circumstances that can cause an explosion ina hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoida hazard, and recognize the consequence.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside theequipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
IMPORTANT
Identifies informationthat is critical for successful application and understanding of the product.

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 3
Summary of Changes
This manual contains new and updated information.
New and Updated
Information
This revision includes new material for the 2090-K6CK-D44S0 low-profile
connector kit and 2090-CS0DSDS-AAxx interface cable for cascading the safe
torque-off signals from drive-to-drive.
Section Topic Page
Chapter 2 Added a description and connection diagram for the 2090-K6CK-D44S0 connector kit. 16
Chapter 3 Updated Safety Input Wiring diagram to use 24VPWR (IOD-14, IOD-15) 22
Chapter 4
Updated Cascaded Connections diagram to use 24VPWR (IOD-14, IOD-15) 27
Updated 2090-K6CK-D44M wiring examples to use 24VPWR (IOD-14, IOD-15) 28
Added 2090-K6CK-D44S0 wiring examples 29…30
Added Kinetix 6200/6500 cascading safe torque-off cable example 31
Added 2090-CS0DSDS-AAxx cable pinout diagram and termination table
Appendix A Updated General Specifications with value for reset time 37
Addedfootnotestoclarifytheeffect cascading driveshas onreaction timeand resettime

4Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Summary of Changes
Notes:

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 5
Table of Contents
Preface
About This Publication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Who Should Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 1
Safety Concept
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Important Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety Category 4 Performance Definition. . . . . . . . . . . . . . . . . . . . . . 10
Stop Category 0 Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Performance Level and Safety Integrity Level (SIL) CL3 . . . . . . . . . 11
PFD and PFH Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PFD and PFH Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safe State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Safety Reaction Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contact Information If Failure Occurs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Automatic Drive Replacement (ADR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2
Installation and Wiring
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wiring the Safety Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the 2090-K6CK-D44M Low-profile Connector Kit . . . . . . 14
Using the 2090-K6CK-D44S0 Low-profile Connector Kit . . . . . . 16
Using the Motion-allowed Plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Terminal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 3
Safe Torque-off I/O Signals
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Discrepancy Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Reset Input (Reset_In). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safe Stop Output (SS_Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safe Stop Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Safe Stop Wiring Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Table of Contents
Chapter 4
Multi-axis Cascaded Systems
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cascaded Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Safe Stop Wiring Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2090-K6CK-D44M Connector Kit Examples. . . . . . . . . . . . . . . . . . . 28
2090-K6CK-D44S0 Connector Kit Examples . . . . . . . . . . . . . . . . . . 29
Chapter 5
Troubleshooting the Safe Torque-off
Drive
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Nonrecoverable Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Fault Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Input and Output Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Fault Codes and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Status Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Guard Status Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Guard Fault Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix A
Specifications
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Index

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 7
Preface
About This Publication This manual explains how the Kinetix® 6200 and Kinetix 6500 drives can be used
in Safety Integrity Level (SIL) CL3, Performance Level [PLe], or Category
(CAT) 4 applications. It describes the safety requirements, including PFD and
PFH values and application verification information, and provides information
on configuring and troubleshooting the Kinetix 6200 and Kinetix 6500 drives
with safe torque-off functionality.
Who Should Use This Manual Use this manual if you are responsible for designing, configuring, or
troubleshooting safety applications that use Kinetix 6200 or Kinetix 6500 drives
with safe torque-off functionality.
You must have a basic understanding of electrical circuitry and familiarity with
Kinetix 6200 and Kinetix 6500 drives. You must also be trained and experienced
in the creation, operation, and maintenance of safety systems.
Terminology The following table defines common safety terms used in this manual.
Table 1 - Common Safety Terminology
Abbreviation Full Term Definition
1oo2 One out of Two Refers to the behavioral design of a dual-channel safety system.
CAT Category –
EN European Norm The official European Standard.
ESPE Electro-sensitive Protective Equipment
An assembly of devices and/or components working together for protective tripping or presence-
sensing purposes and comprising as a minimum:
·a sensing device.
·controlling/monitoring devices.
·output signal-switching devices (OSSD).
FMEA Failure Mode and Effects Analysis Analysis of potential failure modes to determine the effect upon the system and identify ways to
mitigate those effects.
IEC International Electrotechnical Commission –
IGBT Insulated Gate Bi-polar Transistors Typical power switch used to control main current.
HFT Hardware Fault Tolerance The HFT equals n, where n+1 faults could cause the loss of the safety function. An HFT of 1 means
that 2 faults are requiredbefore safety is lost.
MP Motion Power –
OSSD Output Signal-switching Device The component of the electro-sensitive protective equipment (ESPE) connected to the control system of a machine, which, when thesensing deviceis actuated during normaloperation, responds by
going to the OFF-state.
PC Personal Computer Computer used to interface with and program your safety system.
PFD Probability of Failure on Demand The average probability of a system to fail to perform its design function on demand.
PFH Probability of Failure per Hour The probability of a system to have a dangerous failure occur per hour.
PL Performance Level ISO 13849-1 safety rating.
S0 2094-SE02F-M00-S0 Catalog number for Kinetix 6200drives with Safe Torque-off functionality.
2094-EN02D-M01-S0 Catalog number for Kinetix 6500 drives withSafe Torque-off functionality.

8Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Preface
Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
You can view or download publications at:
http://www.rockwellautomation.com/literature . To order paper copies of technical
documentation, contact your local Allen-Bradley® distributor or Rockwell
Automation sales representative.
SFF Safe Failure Fraction The sum of safe failures plus the sum of dangerous detected failures dividedby the sum of all failures.
SIL Safety Integrity Level A measure of a products ability to lower the risk that a dangerous failure could occur.
SS Safe Stop –
Table 1 - Common Safety Terminology (continued)
Abbreviation Full Term Definition
Resource Description
Kinetix 6200 and Kinetix 6500 Modular Multi-axis Servo Drive
User Manual, publication 2094-UM002 Information on installing, configuring, startup, troubleshooting, and applications for your Kinetix 6200 and Kinetix 6500 servo drive system.
Kinetix 6200 and Kinetix 6500 Safe Speed Monitoring
Safety Reference Manual, publication 2094-RM001 Information on wiring, troubleshooting, and configuring your Kinetix 6200 and Kinetix 6500
servo drives with the safe speed-monitoring functionality.
Kinetix Safe-off Feature
Safety Reference Manual, publication GMC-RM002 Information on wiring and troubleshooting your Kinetix 6000 servo drives with the safe-off feature.
System Design for Control of Electrical Noise Reference Manual,
publication GMC-RM001 Information, examples, and techniques designed to minimize system failures caused by
electrical noise.
EMC Noise Management DVD, publication GMC-SP004
Kinetix Motion Control Selection Guide, publication GMC-SG001 Specifications, motor/servo-drive system combinations, and accessories for Kinetix motion
control products.
Safety Guidelines for the Application, Installation and Maintenance of Solid State
Control, publication SGI-1.1
Describes importantdifferencesbetween solidstate controlandhardwiredelectromechanical
devices.

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 9
Chapter 1
Safety Concept
Introduction This chapter describes the safety performance level concept and how the
Kinetix 6200 and Kinetix 6500 drives can meet the requirements for SIL CL3,
CAT 4, or PLe applications.
Safety Certification The Kinetix 6200 and Kinetix 6500 drives are certified for use in safety
applications up to and including SIL CL3 according to EN 61800-5-2,
EN 61508, and EN 62061, Performance Level PLe and CAT 4 according to
ISO 13849-1. Safety requirements are based on the standards current at the time
of certification.
The TÜV Rheinland group has approved the Kinetix 6200 and Kinetix 6500
drives for use in safety-related applications where the de-energized state is
considered to be the safe state. All of the examples related to I/O included in this
manual are based on achieving de-energization as the safe state for typical
Machine Safety and Emergency Shutdown (ESD) systems.
Topic Page
Safety Certification 9
PFD and PFH Definitions 11
PFD and PFH Data 11
Safe State 12
Safety Reaction Time 12
Contact Information If Failure Occurs 12
Automatic Drive Replacement (ADR) 12

10 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 1 SafetyConcept
Important Safety Considerations
You are responsible for the following:
•The set-up, safety rating, and validation of any sensors or actuators
connected to the system
•Completing a system-level risk assessment and reassessing the system any
time a change is made
•Certification of the system to the desired safety performance level
•Project management and proof testing
•Access control to the system, including password handling
Safety Category 4 Performance Definition
The safety-related parts have to be designed with the following considerations to
achieve Safety Category 4 according to ISO 13849-1:2006:
•The safety-related parts of machine control systems and/or their protective
equipment, as well as their components, must be designed, constructed,
selected, assembled, and combined in accordance with relevant standards
so that they can withstand expected conditions.
•Basic safety principles must be applied.
•A single fault in any of its parts does not lead to a loss of safety function.
•A single fault is detected at or before the next demand of the safety
function, or, if this detection is not possible, then an accumulation of faults
must not lead to a loss of the safety function.
•The average diagnostic coverage of the safety-related parts of the control
system must be high, including the accumulation of faults.
•The mean time to dangerous failure of each of the redundant channels
must be high.
•Measures against common cause failure must be applied.
Stop Category 0 Definition
Stop Category 0 is achieved with immediate removal of power to the actuator,
resulting in an uncontrolled coast to stop. Safe Torque Off accomplishes a Stop
Category 0 stop.
IMPORTANT
When applying functional safety, restrict access to qualified, authorized
personnel who are trained and experienced.
ATTENTION: When designing your system,consider how personnel will exit
the machine if the door locks while they are in the machine. Additional
safeguarding devices may be required for your specific application.

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 11
Safety Concept Chapter 1
Performance Level and Safety Integrity Level (SIL) CL3
For safety-related control systems, Performance Level (PL), according to ISO
13849-1, and SIL levels, according to EN 61508 and EN 62061, include a rating
of the system’s ability to perform its safety functions. All of the safety-related
components of the control system must be included in both a risk assessment and
the determination of the achieved levels.
Refer to the ISO 13849-1, EN 61508, and EN 62061 standards for complete
information on requirements for PL and SIL determination.
PFD and PFH Definitions Safety-related systems can be classified as operating in either a Low Demand
mode, or in a High Demand/Continuous mode:
•Low Demand mode: where the frequency of demands for operation made
on a safety-related system is no greater than one per year or no greater than
twice the proof-test frequency.
•High Demand/Continuous mode: where the frequency of demands for
operation made on a safety-related system is greater than once per year or
greater than twice the proof test interval.
The SIL value for a low demand safety-related system is directly related to order-
of-magnitude ranges of its average probability of failure to satisfactorily perform
its safety function on demand or, simply, average probability of failure on demand
(PFD). The SIL value for a High Demand/Continuous mode safety-related
system is directly related to the probability of a dangerous failure occurring per
hour (PFH).
PFD and PFH Data These PFD and PFH calculations are based on the equations from Part 6 of
EN 61508 and show worst-case values.
This table provides data for a 20-year proof test interval and demonstrates the
worst-case effect of various configuration changes on the data.
Table 2 - PFD and PFH for 20-year Proof Test Interval
Attribute Value
PFH [1e-9] 4.09
PFD [1e-4] 3.90
SFF % 99.5

12 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 1 SafetyConcept
Safe State The Safe State encompasses all operation that occurs outside of the other
monitoring and stopping behavior defined as part of the drive. While the drive is
in the Safe State, all safety control outputs are in their safe state (de-energized).
When you cycle power, the drive enters the Safe State for self-testing. If the self-
tests pass, the drive remains in the Safe State until a successful safe stop reset
occurs.
If a Safe State fault is detected, the drive goes to the Safe State. This includes
faults related to integrity of hardware or firmware.
For more information on faults, refer to Chapter 5.
Safety Reaction Time The safety reaction time is the amount of time from a safety-related event as
input to the system until the system is in the Safe State.
The safety reaction time from an input signal condition that triggers a safe stop,
to the initiation of the Safe Stop Type, is 12 ms, max.
Contact Information If
Failure Occurs
If you experience a failure with any safety-certified device, contact your local
Rockwell Automation distributor. With this contact, you can do the following:
•Return the device to Rockwell Automation so the failure is appropriately
logged for the catalog number affected and a record is made of the failure.
•Request a failure analysis (if necessary) to determine the probable cause of
the failure.
Automatic Drive
Replacement (ADR)
You can replace IAM and AM power modules, and the associated control
modules, at any time without any need for configuration or program changes.
IMPORTANT
For cascaded systems, thereaction time is multiplied by the number of drives
in the drive system. For example, drive systems with three cascaded drives
(first, middle, and last), have a reaction time of 36 ms, max.

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 13
Chapter 2
Installation and Wiring
Introduction This chapter provides details on connecting devices and wiring the
2090-K6CK-D44M and 2090-K6CK-D44S0 low-profile connector kits.
General Safety Information Observe all electrical safety regulations stipulated by the appropriate technical
authorities.
Refer to the Kinetix 6200 and Kinetix 6500 Modular Multi-axis Servo Drive
User Manual, publication 2094-UM002, for more information.
Topic Page
General Safety Information 13
Power Supply Requirements 14
Wiring the Safety Connections 14
Terminal Connections 18
ATTENTION: The drive is intended to be part of the safety-related control
system of a machine. Before installation, a risk assessment should be
performed to determine whether the specifications of this safety option are
suitable for all foreseeable operational and environmental characteristics for
the system to which it is to be installed.
ATTENTION: Make sure that the electrical power supplied to the drive is
switched off beforemaking connections.

14 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 2 Installation and Wiring
Power Supply Requirements The external power supply must conform to the Directive 2006/95/EC Low
Voltage, by applying the requirements of EN61131-2 Programmable Controllers,
Part 2 - Equipment Requirements and Tests and one of the following:
•EN60950 - SELV (safety extra low voltage)
•EN60204 - PELV (protective extra low voltage)
•IEC 60536 Safety Class III (SELV or PELV)
•UL 508 Limited Voltage Circuit
•21.6…28.8V DC must be supplied by a power supply that complies with
IEC/EN60204 and IEC/EN 61558-1
For planning information, refer to the guidelines in Industrial Automation
Wiring and Grounding Guidelines, publication 1770-4.1.
Wiring the Safety
Connections
Safety, I/O, and auxiliary feedback connections are made by using the
2090-K6CK-D44M low-profile connector kit. I/O and cascading drive-to-drive
safe torque-off connections can be made by using the 2090-K6CK-D44S0
low-profile connector kit. When the safety, I/O, and auxiliary feedback are not
required for the application, the motion-allowed plug is used to make the drive
operational.
Using the 2090-K6CK-D44M Low-profile Connector Kit
The 2090-K6CK-D44M connector kit includes one motion-allowed jumper.
Remove the jumper to wire the safe torque-off connections. Install the jumper
when your application is not using the safe torque-off functionality, but your
application requires I/O or auxiliary feedback connections.
IMPORTANT
Removepower to the IAM or AM power module before installing eitherthe
low-profile connector kit or the motion-allowed plug.
IMPORTANT
You must remove the motion-allowed jumper to wire thesafe torque-off
connections.

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 15
Installation and Wiring Chapter 2
Figure 1 - Making 2090-K6CK-D44M Safety Connections
Refer to the Kinetix 6200 and Kinetix 6500 Modular Servo Drive User Manual,
publication 2094-UM002, for other wiring examples using low-profile connector
kits.
28 27 26 25 24 23 22 21 20 19 18 17 15 14 0
AUX FEEDBACK
0 11 10 9 8 7 6 5 4 3 2 1
0 39 41 40 39 42 40 39 43 40 39 44 40
INPUTS
0 38 37 36 35 34 33 32 31 30 29 28 27 28 27 28 27 28 27
S1 ONLY S1 ONLY
S0&S1 W/S0 DISABLED
28 27 26 25 24 23 22 21 20 19 18 17 15 14 0
AUX FEEDBACK
0 11 10 9 8 7 6 5 4 3 2 1
0 39 41 40 39 42 40 39 43 40 39 44 40
INPUTS
0 38 37 36 35 34 33 32 31 30 29 28 27 28 27 28 27 28 27
S1 ONLY S1 ONLY
S0&S1 W/S0 DISABLED
28 27 26 25 24 23 22 21 20 19 18 17 15 14 0
2090-K6CK-D44M
Low-profile Connector Kit
Use tie wraps (4x)
for stress relief.
Turn clamps over for smaller
diameter cables.
Aux Feedback and I/O
Wires and Cables
Motion-allowed Jumper Installation
(applies to 2094-xx02x-M0x-S0
control modules)
Safety Wires
and Cables
Use shield clamps (3x) for
high-frequency bonding.
Kit pin numbering corresponds to the IOD
connector. Pins 27, 28, 39, and 40 are given
multiple terminals to accommodate
additional connections.
Refer to page 18 for safety, auxiliary
feedback, and I/O signal descriptions.
Shrink-wrapped
Insulation
Clamp

16 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 2 Installation and Wiring
Using the 2090-K6CK-D44S0 Low-profile Connector Kit
The 2090-K6CK-D44S0 connector kit includes two motion-allowed jumpers.
Remove the jumpers to wire the safe torque-off connections. Install the jumper
when your application is not using the safe torque-off functionality, but your
application requires I/O connections.
The 2090-K6CK-D44S0 connector kit lets you cascade the safe torque-off
signals from drive-to-drive by using the 2090-CS0DSDS-AAxx interface cable.
Figure 2 - Making 2090-K6CK-D44S0 Safety Connections
Refer to the Kinetix 6200 and Kinetix 6500 Modular Servo Drive User Manual,
publication 2094-UM002, for other wiring examples using low-profile connector
kits.
IMPORTANT
You must remove the motion-allowed jumpers to wire the safe torque-off
connections.
P2
P1
P4
P3
P6
P5
P2
P1
P4
P3
P6
P5
40
42
39
39
41
40
0
40
44
39
39
43
40
14
25
17
26
18
15
0
0
27
28
19
20
23
24
21
22
27
28
19
20
23
24
21
22
14
25
17
26
18
15
0
0
40
42
39
39
41
40
0
40
44
39
39
43
40
S0
IN
S0
OUT
14
25
17
26
18
15
0
0
2090-K6CK-D44S0
Low-profile Connector Kit
Turn clamps overfor smaller
diameter cables.
Motion-allowed Jumper Installation
(applies to 2094-xx02x-M0x-S0
control modules)
Pin numbering corresponds tothe IOD (44 pin)
connector. IOD-39 = P1-39 and P2-39.
Pins 39 and40 are given multiple terminals to
accommodate connections for each of the inputs.
Refer to page 18 for safety and
I/O signal descriptions.
Shrink-wrapped Insulation
Use shield clamps (2) to maximize contact with
cable shield for high-frequency bonding.
Use tie wraps (2) for stress relief.
I/O
Cable/Wires Cascading S0
Safe-off Cables Safety
Cable/Wires

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 17
Installation and Wiring Chapter 2
Using the Motion-allowed Plug
Because the safe torque-off feature of Kinetix 6200 and Kinetix 6500 control
modules (catalog numbers 2094-xx02x-M0x-S0) is not configured, the safe
torque-off functionality is always operational. If you do not want to use the safe
torque-off feature, wiring of the safe stop inputs (SS_IN_CH0/1) are still
required to operate the drive.
For this reason, the 2094-xx02x-M0x-S0 control modules ship with the
motion-allowed plug. The plug inserts into the IOD connector and provides
connections designed to defeat the safe torque-off function.
Figure 3 - Motion-allowed Plug Wiring
Figure 4 - Motion-allowed Plug Installation
IOD Connector
TEST_OUT_1
TEST_OUT_0
RESET_IN
RESET_REF
28
27
26
25
24
23
22
21
20
19
18
17
15
14
SLS_IN_CH3
SLS_IN_CH2
SS_OUT_CH1
SS_OUT_CH0
SS_IN_CH1
SS_IN_CH0
SCOM
SPWR
28
27
26
25
24
23
22
21
20
19
18
17
15
14
24VCOM
24VPWR
Kinetix 6200 and Kinetix 6500
Safe Torque-off Control Module
IOD (44-pin) Connector
TIP
If your application does not require any I/O, safety, or auxiliary feedback
connections, use the motion-allowed plug supplied with your drive to defeat
the safe torque-off functionality.
Kinetix 6200 or Kinetix 6500 Drive
(safe torque-off control module)
I/O, safety, and auxiliary feedback
(IOD) 44-pin connector with
motion-allowed plug installed.

18 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 2 Installation and Wiring
Terminal Connections Prepare wires for termination on the IOD connector with a 5 mm (0.2 in.) strip
length. Tighten all terminal screws firmly and recheck them after all connections
have been made. Recommended terminal screw torque is 0.4 N•m (3.5 lb•in).
Refer to page 37 for the I/O signal electrical specifications.
Table 3 - IOD Connector Pinouts
IOD
Pin Description Signal IOD Pin Description Signal
0 Chassis ground Shield
23 Safe stop input 2 SS_IN_CH2
1Sine differential input +
A differential input + AUX_SIN+ AUX_A+
2Sine differential input -
A differential input - AUX_SIN- AUX_A- 24 Safe stop input 3 SS_IN_CH3
3Cosine differential input +
B differential input + AUX_COS+ AUX_B+ 25 Reset reference RESET_REF
4Cosine differential input -
B differential input - AUX_COS- AUX_B- 26 Reset input RESET_IN
5Data differential input +
Index differential input + AUX_DATA+ AUX_I+ 27 Pulse test output 0 TEST_OUT_0
6Data differential input -
Index differential input - AUX_DATA- AUX_I- 28 Pulse test output 1 TEST_OUT_1
7 Clock output + AUX_CLK+ 29 Reserved –
8 Clock output - AUX_CLK- 30 Reserved –
9 Encoder5V power output EPWR_5V 31 Reserved –
10 Encoder common ECOM 32 Reserved –
11 Encoder 9V power output EPWR_9V 33 Reserved –
12 Reserved – 34 Reserved –
13 Reserved – 35 Reserved –
14 24V power out 24VPWR (1) 36 Reserved –
15 24V common 24VCOM (1) 37 Reserved –
16 Reserved – 38 Reserved –
17 Safety 24V power input SPWR 39 24V power out 24VPWR (2)
18 Safety 24V common SCOM 40 24V common 24VCOM
19 Safe stop input 0 SS_IN_CH0 41 Digital input 1 INPUT1
20 Safe stop input 1 SS_IN_CH1 42 Digital input 2 INPUT2
21 Safe stop output 0 SS_OUT_CH0 43 Digital input 3 INPUT3
22 Safe stop output 1 SS_OUT_CH1 44 Digital input 4 INPUT4
(1) Use this supply to power the Safety 24V (SPWR/SCOM) input. Do not connect this 24V supply to any external safety device. Refer to Figure 8 on page 22 for an example.
(2) Use signals 24VPWR and 24VCOM (IOD-39 and IOD-40) as a 24V DC source to operate the digital inputs (50 mA maximum per input).

Rockwell Automation Publication 2094-RM002B-EN-P - May 2012 19
Chapter 3
Safe Torque-off I/O Signals
Introduction This chapter describes the safe torque-off input and output signals of the
Kinetix 6200 and Kinetix 6500 drives.
Inputs The Kinetix 6200 and Kinetix 6500 drives have two sets of dual-channel inputs.
Each dual-channel input supports the safe stop (SS) function of the drive.
The SS_IN_CH0/1 inputs are intended for connection to a non-switching
E-stop device (dry contact). It controls the safe-off request initiated by a
transition from ON to OFF.
The SS_IN_CH2/3 inputs are intended for connection to an OSSD device or as
a cascaded input from another safety axis. It controls the safe-off request initiated
by a transition from ON to OFF.
The SS_IN_CH0/1 inputs are electrically identical and rely on a pair of pulse
test outputs, TEST_OUT_0 and TEST_OUT_1.
When both channels are active, if one channel’s input terminal transitions from
active to inactive and back to active, while the other channel’s input terminal
remains active, both channels must go inactive at the same time before the
evaluated status may return to ON. This condition is called ‘cycle inputs
required’.
Topic Page
Inputs 19
Outputs 23
Safe Stop Wiring Example 26
IMPORTANT
Only one pair of dual-channel inputs can be used at the same time.

20 Rockwell Automation Publication 2094-RM002B-EN-P - May 2012
Chapter 3 Safe Torque-off I/O Signals
Figure 5 - Cycle Inputs Required
An Input fault occurs if the inputs are discrepant for longer than one second.
For SS_IN_CH0/1, use TEST_OUT_0/1 as a reference signal, or a fault occurs.
For more information on I/O faults, refer to Troubleshooting the Safe Torque-off
Drive on page 33.
Discrepancy Time
The maximum discrepancy time between two inputs is 1.0 second. If both inputs
do not change within 1.0 second, an input fault is displayed, the safety circuit is
activated, and torque is removed from the motor.
Figure 6 - Discrepancy Time
Behavior of reset and safe-off inputs while transitioning from Safe_Off state to
Safe_Monitor state.
Channel 0 Active
Inactive
Channel 1 Active
Inactive
Evaluated Status ON
OFF
Cycle Inputs Required
SS_IN_CH0 or
SS_IN_CH2
SS_IN_CH1 or
SS_IN_CH3
Gate Power
and Gate Enable
RESET_IN
Fault
ton
Ton (max) = 20 ms
plus Debounce Filter Delay
(if applicable).
Safe-off inputs return to
inactive state before Gate
Power can be restored.
Input Discrepancy
Time (1.0 s)
Latch Input Error
Time (1.0 s)