AllerAir 600 D Manual

INSTALLING FILTER ASSEMBLY- 600 D, DX
Step 3
Gently grasp wheels.
Remove base by gently pulling on
the wheels.
Step 1
Turn Power Off and
unplug receptacle.
Lay unit upside down.
Step 5
Insert the carbon filter (either a
Model 600 D Carbon or a Model 600
DX Carbon) into the unit.
Step 4
Remove only one of the white,felt,
donut-shaped gaskets from the
inside of the purifier body.
Step 6
Replace the gasket that had been
removed in STEP 4.
Step 2
With a #2 Philips screw driver,
remove the four screws from the
bottom of the unit.
Step 8
Replace the four screws
Step 7
Place lid back to its proper position
by aligning the arrow with the rear
seam.
Step 9
Turn the unit back onto its wheels.
It is now ready for immediate use.
The AllerAir 600 models ship with their large carbon filters in a separate box.
This is done to safeguard your unit during shipping. To insert the filter, refer to the diagram below.
AllerAir Industries Inc. Toll free:1-888-852-8247 / Fax:[phone] www.allerair.com
INSTALLING FILTER ASSEMBLY- 600 Models
(except D and DX)
The AllerAir 600 models ship with their large carbon filters in a separate box.
This is done to safeguard your unit during shipping. To insert the filter, refer to the diagram below.
AllerAir Industries Inc. Toll free:1-888-852-8247 / Fax:[phone] www.allerair.com
Step 3
Gently grasp wheels.
Step 1
Turn Power Off and
unplug receptacle.
Lay unit upside down.
Step 4
Remove base by gently pulling on
the wheels.
Step 5
First remove the HEPA filter by
placing thumbs on the inner side of
the filter.
Then pull up gently until totally out.
Step 6
Than remove the Carbon filter by
placing thumbs on the inner side of
the filter.
Then pull up gently until totally out.
Step 2
With a #2 Philips screw driver,
remove the four screws from the
bottom of the unit.
Step 8
Place lid back to its proper position
by aligning the arrow with the rear
seam.
Step 9
With a screw driver, place 4
screws back into their positions.
Gently return the unit into
upright position.
Step 7
Replace filters with new ones then
reassemble by inserting the Carbon
filter first then the HEPA filter.

INSTALLING FILTER ASSEMBLY- 600 D, DX
Step 3
Gently grasp wheels.
Remove base by gently pulling on
the wheels.
Step 1
Turn Power Off and
unplug receptacle.
Lay unit upside down.
Step 5
Insert the carbon filter (either a
Model 600 D Carbon or a Model 600
DX Carbon) into the unit.
Step 4
Remove only one of the white,felt,
donut-shaped gaskets from the
inside of the purifier body.
Step 6
Replace the gasket that had been
removed in STEP 4.
Step 2
With a #2 Philips screw driver,
remove the four screws from the
bottom of the unit.
Step 8
Replace the four screws
Step 7
Place lid back to its proper position
by aligning the arrow with the rear
seam.
Step 9
Turn the unit back onto its wheels.
It is now ready for immediate use.
The AllerAir 600 models ship with their large carbon filters in a separate box.
This is done to safeguard your unit during shipping. To insert the filter, refer to the diagram below.
AllerAir Industries Inc. Toll free:1-888-852-8247 / Fax:[phone] www.allerair.com
INSTALLING FILTER ASSEMBLY- 600 Models
(except D and DX)
The AllerAir 600 models ship with their large carbon filters in a separate box.
This is done to safeguard your unit during shipping. To insert the filter, refer to the diagram below.
AllerAir Industries Inc. Toll free:1-888-852-8247 / Fax:[phone] www.allerair.com
Step 3
Gently grasp wheels.
Step 1
Turn Power Off and
unplug receptacle.
Lay unit upside down.
Step 4
Remove base by gently pulling on
the wheels.
Step 5
First remove the HEPA filter by
placing thumbs on the inner side of
the filter.
Then pull up gently until totally out.
Step 6
Than remove the Carbon filter by
placing thumbs on the inner side of
the filter.
Then pull up gently until totally out.
Step 2
With a #2 Philips screw driver,
remove the four screws from the
bottom of the unit.
Step 8
Place lid back to its proper position
by aligning the arrow with the rear
seam.
Step 9
With a screw driver, place 4
screws back into their positions.
Gently return the unit into
upright position.
Step 7
Replace filters with new ones then
reassemble by inserting the Carbon
filter first then the HEPA filter.