Allied Telesis AR400 Series User manual

C613-16037-00 REV C www.alliedtelesis.com
AlliedWare™ OS
How To |
Introduction
This How To Note shows an example of using a dynamic routing protocol over an L2TP
tunnel.
Running dynamic routing protocols over a secure Internet connection can be a complex
issue, with the possibility of intermittent connections causing routing problems.
OSPF (or BGP) are more connection-oriented than RIP and therefore are more susceptible
to problems caused by intermittent loss of connection between 'neighbours'. A neighbour
that may bounce up and down can cause havoc to the correct propagation of OSPF routing
information for a network.
The following example scenario is for setting up RIP over an L2TP tunnel. RIP is simpler and
has less overhead and control, so it provides a more robust setup as a dynamic routing
protocol over an L2TP tunnel.
Which products does it apply to?
This Note applies to the following Allied Telesis routers, running software version 2.6.1 or
later:
zAR400 series
zAR700 series
Configure Dynamic Routing Over An L2TP Tunnel

Page 2 | AlliedWare™ OS How To Note: Dynamic Routing over L2TP
An example scenario for RIP over L2TP
Related How To Notes
You may also find the following How To Notes useful:
zHow To Configure Remote L2TP Tunnels
zHow To Configure Allied Telesis and Cisco Routers To Interoperate Over L2TP
How To Notes are available from www.alliedtelesis.com/resources/literature/howto.aspx.
An example scenario for RIP over L2TP
Our example uses two office sites that are connected via a WAN connection over the
Internet using an L2TP tunnel for security.
The setup (shown below) shows the 'Central office' and 'Remote office' routers connected,
in this case, back to back via their Ethernet interfaces (this would likely be the remote WAN
connection across the Internet, with perhaps static IP assignment from the ISPs).
WAN
X PC
HUB
POWER ETH0
X PC
HUB
POWER
ETH0
Central office router
Remote office router
VLAN 2 IP=222.222.2.1
VLAN 1 IP=222.222.1.1
VLAN 2 IP=200.200.2.1
VLAN 1 IP=200.200.1.1
192.168.1.1
192.168.2.1
Eth0 IP=10.10.10.1
Eth0 IP=10.10.10.2
PPP0 over
L2TP tunnel
RIP propogates
VLAN OSPF
routes over
L2TP tunnel
to remote router
OSPF used on
local VLAN
networks
OSPF used on
local VLAN
networks
rip-l2tp.eps

Page 3 | AlliedWare™ OS How To Note: Dynamic Routing over L2TP
An example scenario for RIP over L2TP
Network Operation
There is a single static route configured to bring up the L2TP tunnel and a secure point-to-
point connection (PPP0) is established over the L2TP tunnel between the 'Central' and
'Remote' office routers. This allows secure communication between the offices across the
Internet.
Each local office site is using OSPF as their routing protocol, as it offers some advanced
routing features and is scalable and flexible. The 'local' VLAN networks in our example at
each office site use OSPF.
RIP is used across the secure Internet connection between offices to provide a more robust
network, as discussed previously. So RIP is used on the point-to-point interface (PPP0) over
the L2TP tunnel. OSPF is configured to import and export routing information with RIP.
This allows RIP to propagate the dynamically learnt OSPF 'local' VLAN network information
to the other office router.
Routing Information
The routing table in each router shows locally learnt routes and the routes learnt from the
remote router via RIP across the L2TP tunnel. The example output below is from the show
ip route command on the 'Central office' router.
You can see that the 'local' VLAN networks (222.222.1.0 and 222.222.2.0) have been learnt
via OSPF. The 'Remote office' OSPF VLAN networks (200.200.1.0 and 200.200.2.0) have
been learnt via RIP. These were exported from OSPF on the 'Remote' router and propagated
by RIP over the secure point-to-point connection (PPPO) using the L2TP tunnel.
IP Routes
-----------------------------------------------------------------------------
Destination Mask NextHop Interface Age
Type Policy Protocol Metrics Preference
-----------------------------------------------------------------------------
10.10.10.0 255.255.255.0 0.0.0.0 eth0 644
direct 0 interface 1 0
10.10.10.0 255.255.255.0 10.10.10.2 eth0 644
direct 0 static 1 60
10.10.10.0 255.255.255.0 192.168.1.2 ppp0 627
remote 0 rip 2 100
192.168.1.0 255.255.255.0 0.0.0.0 ppp0 644
direct 0 interface 1 0
200.200.1.0 255.255.255.0 192.168.1.2 ppp0 627
remote 0 rip 2 100
200.200.2.0 255.255.255.0 192.168.1.2 ppp0 627
remote 0 rip 2 100
222.222.1.0 255.255.255.0 0.0.0.0 vlan1 644
direct 0 interface 1 0
222.222.1.0 255.255.255.0 0.0.0.0 vlan1 641
remote 0 ospf-Intra 1 10
222.222.2.0 255.255.255.0 0.0.0.0 vlan2 644
direct 0 interface 1 0
222.222.2.0 255.255.255.0 0.0.0.0 vlan2 636
remote 0 ospf-Intra 1 10
-----------------------------------------------------------------------------

Page 4 | AlliedWare™ OS How To Note: Dynamic Routing over L2TP
An example scenario for RIP over L2TP
Routing Considerations
A routing issue to consider in this set up is the fact that RIP is relatively slow to react to
route changes as it only updates, by default, every 30 seconds.
To improve the responsiveness of RIP you can alter the default timers for updating, flushing
and so on. You do need to keep in mind that if you lose some packets (quite possible across
a lossy Internet connection) some of your routes may flap too much. So the RIP timers need
to be adjusted to provide an optimal compromise between responsiveness and robustness.
In this particular example, the various RIP timers are set at half default value.
set ip riptimer update=15 invalid=90 holddown=60 flush=150
Consideration would need to be given to each specific set up to get an optimal balance when
adjusting these timers.

Page 5 | AlliedWare™ OS How To Note: Dynamic Routing over L2TP
Configurations
Configurations
Central Office Router
set system name=Central_Office
enable l2tp
enable l2tp server=both
add l2tp call="tunnel" rem="tunnel" ip=10.10.10.2 ty=virtual prec=in
create vlan="vlan2" vid=2
add vlan="2" port=3,4
create ppp=0 over=tnl-tunnel
set ppp=0 bap=off username="chap" password="chap"
enable ip
add ip int=eth0 ip=10.10.10.1 mask=255.255.255.0
add ip int=ppp0 ip=192.168.1.1
add ip int=vlan1 ip=222.222.1.1
add ip int=vlan2 ip=222.222.2.1
add ip rou=10.10.10.0 mask=255.255.255.0 int=eth0 next=10.10.10.2
add ip rip int=ppp0 send=rip2 receive=rip2
set ip riptimer update=15 invalid=90 holddown=60 flush=150
set ospf routerid=222.222.1.1 rip=both
add ospf area=backbone stubarea=off summary=send
add ospf range=222.222.1.0 area=backbone mask=255.255.255.0
add ospf range=222.222.2.0 area=backbone mask=255.255.255.0
add ospf interface=vlan1 area=backbone
add ospf interface=vlan2 area=backbone
enable ospf

USA Headquarters | 19800 North Creek Parkway | Suite 100 | Bothell | WA 98011 | USA | T: [phone] | F: [phone]
EuropeanHeadquarters | Via Motta 24 | 6830 Chiasso | Switzerland | T: +41 91 69769.00 | F: +41 91 69769.11
Asia-Pacific Headquarters | 11 Tai Seng Link | Singapore | 534182 | T: [phone] | F: [phone]
www.alliedtelesis.com
© 2008 Allied Te l esis, Inc. All rights reserved. Information in this document is subject to change without notice.
All company names, logos, and product designs that are trademarks or registered trademarks are the property of their respective owners.
Allied Telesis is a trademark or registered trademark of Allied Telesis, Inc. in the United States and other countries.
C613-16037-00 REV C
Remote Office Router
set system name=Remote_Office
enable l2tp
enable l2tp server=both
add l2tp call="tunnel" rem="tunnel" ip=10.10.10.1 ty=virtual prec=out
create vlan="vlan2" vid=2
add vlan="2" port=3,4
create ppp=0 over=tnl-tunnel
set ppp=0 bap=off username="chap" password="chap"
enable ip
add ip int=ppp0 ip=192.168.1.2
add ip int=eth0 ip=10.10.10.2 mask=255.255.255.0
add ip int=vlan1 ip=200.200.1.1
add ip int=vlan2 ip=200.200.2.1
add ip rou=10.10.10.0 mask=255.255.255.0 int=eth0 next=10.10.10.1
add ip rip int=ppp0 send=rip2 receive=rip2
set ip riptimer update=15 invalid=90 holddown=60 flush=150
set ospf routerid=200.200.1.1 rip=both
add ospf area=backbone stubarea=off summary=send
add ospf range=200.200.1.0 area=backbone mask=255.255.255.0
add ospf range=200.200.2.0 area=backbone mask=255.255.255.0
add ospf interface=vlan1 area=backbone
add ospf interface=vlan2 area=backbone
enable ospf