Allnet 195630 User manual

Plusonic USB NFC Card Reader

Part No. 195630

Quick Install Guide

Errors and omissions excepted.

1. Introduction

The Plusonic USB NFC Card Reader is a PC-linked Contactless Smart Card

Reader/Writer developed on the 13.56MHz Contactless Technology. It is the

world’s first CCID Compliant Contactless Card Reader/Writer that follows both

ISO14443 and ISO18092, This device is designed to support not only MiFare

and ISO14443 Type A and B Cards but also FeliCa and NFC tags.

By making use of high-speed card access and full USB speed of 12 Mbps, read

and write operations are faster and more efficient. Furthermore, this reader

acts as a Plug and Play(PnP) device so there is no need to provide additional

drivers to users. With its compact size, trendy design and with the various

features the Plusonic USB NFC Card Reader offers, you can experience the

convenience in using this device for applications of payment, mass transit,

physical access control, time attendance, etc.

2. Installation

1. Plug the Card reader into the USB port of the PC. The LED will light up.

2. PC shows “found new hardware”.

3. The Hardware Update Wizard pops up.

4. Start the driver installation by clicking “Next”. The required drivers will

be installed via the Windows Updates.

5. After the successful installation of the devices drivers, in the Device

Manager, it shows the device as “USB Smart Card Reader”. Now you

can start using the Card Reader.

In case Windows Updates are not available or did not find any Updates, please

the drivers for the Plusonic USB NFC Card Reader.

If you want to use the writing function of the device additional software is

required.

Errors and omissions excepted.

3. Safety Instructions

Please be sure to observe the following instructions:

General notes

•Only use the device for the purpose it was designed.

•Only use the device as described in the Quick Start Guide or manual.

•Any other use is considered improper and may result in property damage.

•Neither ALLNET®nor the dealer accepts liability for damage caused by

improper or incorrect use.

•All safety instructions must be read through.

•The manual should be kept for future reference.

Mounting instructions

•NEVER place the device near radiators, air conditioners or water sources.

This greatly increases the risk of electric shocks, short circuits or fire.

•The humidity should be between 20% and 80%, otherwise condensation

may occur.

•Protect the device from direct sunlight, extreme heat, open fire and dust.

Otherwise, the risk of electric shocks, short circuits or fire increases.

•Never place the device on surfaces that are sensitive to heat.

•Do not use the device in damp rooms and under no circumstances in

potentially explosive areas.

•The device is designed for use in enclosed spaces.

Errors and omissions excepted.

Operating notes

•Operate the device only with the voltage indicated on the device or on

the included power supply unit.

•Any batteries present are only to be replaced with the same or an

equivalent type.

•Do not use obviously defective devices. If the unit does not operate

normally – especially if unusual odors or noises occur – unplug the power

cord from the socket immediately.

•Never expose the device to direct sunlight during operation.

•Never operate the device near sources of heat.

•Protect the device from moisture, dust, liquids and vapors.

•Never open the device.

•Work on the device may only be carried out when the device has been

disconnected from its power source.

•The device may only be operated by persons who have read the

instructions or have been instructed in its operation by a competent

person.

Instructions for repair and maintenance.

•Repairs may only be carried out by trained, authorized personnel.

•Regular maintenance is not necessary.

•Never open the device.

•For cleaning work, disconnect the device from its power source.

•Do not use any cleaning agents containing solvents for cleaning, but only

a soft, dry antistatic cloth.

•It is forbidden to make any modifications to the unit.

•Damaged devices or damaged components may no longer be used.

Errors and omissions excepted.

ALLNET GmbH Computersysteme declares that the device Plusonic USB NFC Card

Reader is in compliance with the essential requirements and other relevant provisions

of Directive 2014/30/EU. The Declaration of conformity can be found under this link:

http://ce.allnet.de

ALLNET GmbH Computersysteme

Maistrasse 2

82110 Germering

Tel.: +49 (0)89 894 222 - 22

Fax: +49 (0)89 894 222 - 33

Email: [email protected]

CE Marking is the symbol as shown above. The letters “CE” are the abbreviation of the

French phrase “Conformity European” which literally means “European Conformity”.

The terms initial use was as the “EC Mark”. With the Directive 93/68/EEC from 1993 it

was officially replaced by the “CE Marking”. Nowadays the “CE Marking” is used in all

EU official documents.

Errors and omissions excepted.

This symbol on the product or on its packaging indicate that this

product is not to be disposed with your other household waste.

Instead, it is your responsibility to dispose of your waste equipment

by handing it over to a designated collection point for the recycling

of electrical waste or electronic equipment. The separate collection

and recycling of your waste equipment will help to conserve natural

resources and ensure that it is recycled in a manner that protects

human health and environment. For more information about where

you can dispose your waste equipment, please contact your local city office, your

household disposal service or the shop where you purchased the product.

This recycle logo indicates that this product can be recycled, not that the

product has been recycled. It is possible that this device will not be

accepted in all recycling collection systems.

The recycling codes are used to guarantee the correct handling of waste. It is

an internationally recognized classification that assigns a unique number to

each waste material. This number provides information on how the waste

material can best be recycled to ensure the least possible impact on the

environment. The code PAP 22 describes these instructions for the device, which were

printed on paper. They should be disposed of through the usual recycling channels, such

as waste paper collection points.

The RoHS directive aims to restrict certain dangerous substances commonly

used in electronic and electronic equipment. This RoHS compliant symbol

indicate the component is tested for the presence of Lead (Pb), Cadmium (Cd), Mercury

(Hg), Hexavalent chromium (Hex-Cr), Polybrominated biphenyls (PBB), and

Polybrominated diphenyl ethers (PBDE). For Cadmium and Hexavalent chromium, there

must be less than 0.01% of the substance by weight at raw homogeneous materials

level. For Lead, PBB, and PBDE, there must be no more than 0.1% of the material, when

calculated by weight at raw homogeneous materials. Any RoHS compliant component

must not have more than 100 ppm of mercury and the mercury must not have been

intentionally added to the component.

This manual suits for next models

Table of contents

Allnet 195630 User manual

Popular Card Reader manuals by other brands