AllSportSystems SkyBridge User manual

AllSportSystems, Inc.© 2020.
SkyBridge Installation Guide
Page 1 of 9

AllSportSystems, Inc.© 2020.
Cutting your strut to size:
Just as you would for the width poles in your enclosure, you will need
to cut your strut channel to fit within the cage itself.
Precut extender kits are available for purchase HERE
Follow the below chart for what lengths you will need to cut your strut
channel:
Hitting Bay
Size
Strut Lengths needed for SCREEN
ONLY
Strut Lengths needed for Screen and
Front Width
SuperBay™
10W x 9H x 5D
1ea. 10’ length
Width: Strut cut to 9’9” ea.
2ea. 10’ lengths
Width: Struts cut to 9’9” ea.
SuperBay™
12W X 9H x 5D
2ea. 10’ lengths
Width: 1ea. Strut at 10’0” (no cut
needed)
Extender: 1ea. Strut cut at 1’9” from
remaining 10’ length
3ea. 10’ lengths
Width: 2ea. Struts at 10’0” (no cut
needed)
Extenders: 2ea. Struts cut at 1’9” from
remaining 10’ length
SuperBay™
14W x 9H x 5D
2ea. 10’ lengths
Width: 1ea. Strut at 10’0” (no cut
needed)
Extender: 1ea. Strut cut at 3’9” from
remaining 10’ length
3ea. 10’ lengths
Width: 2ea. Struts at 10’0” (no cut
needed)
Extenders: 2ea. Struts cut at 3’9” from
remaining 10’ length
SuperBay™
16W x 9H x 5D
2ea. 10’ lengths
Width: 1ea. Strut at 10’0” (no cut
needed)
Extender: 1ea. Strut cut at 5’9” from
remaining 10’ length
4ea. 10’ lengths
Width: 2ea. Struts at 10’0” (no cut
needed)
Extenders: 2ea. Struts cut at 5’9” from
remaining 10’ lengths
Page 2 of 9

AllSportSystems, Inc.© 2020.
Step 1: Attach SkyBridge to Unistrut
● Insert 2 of the included Unistrut nuts into each end of the Unistrut.
● Line up the SkyBridge bracket with the 2 Unistrut nuts.
Page 3 of 9

AllSportSystems, Inc.© 2020.
●Using a 7/16” wrench or socket, fasten your SkyBridge bracket to the
Unistrut using the included 1/4-20 bolts and washers.
● Remove the clamp using a 5/16” wrench or socket to unscrew it from
the bracket.
Page 4 of 9

AllSportSystems, Inc.© 2020.
Step 2: Attach Unistrut with SkyBridge brackets to
your cage.
● Bring the open bracket to the point on your cage where you wish to
hang the Unistrut and attach it by screwing the clamp to the bracket
going around the pipe or coupling.
● Note: If hanging your impact screen from the Unistrut, be sure to
position it according to your hitting bay’s instructions.
Page 5 of 9

AllSportSystems, Inc.© 2020.
Appendix:
● For cages wider than 10’, you will need to add an extension to reach
the sides of your enclosure.
Parts Needed:
●2 each - 4 Hole Unistrut Plate
●4 each - 2” x ½” Bolts
●4 each - ½” Nuts
●8 each - ½” Washers
● Single piece of Unistrut cut to the additional length needed for your
cage
Tools Needed:
● 2 each - ¾” Wrench and/or Socket
Page 6 of 9

AllSportSystems, Inc.© 2020.
Step 1: Line up Unistrut and extender
● Line up the ends of your unistrut and unistrut extender
Page 7 of 9

AllSportSystems, Inc.© 2020.
Step 2: Begin attaching extender with plate and bolts
● Line up one of the 4 hole unistrut plates with the ends of the unistrut,
dropping the four ½” bolts with washers through the holes of the
plate.
Page 8 of 9

AllSportSystems, Inc.© 2020.
● On the back side of the unistrut, attach the second 4 hole unistrut
plate with the four ½” nuts and washers, securing with ¾” wrenches
Page 9 of 9