Alphatech BlueGate SIP User manual

ALPHATECH TECHNOLOGIES s.r.o.
Jeremenkova 88, Praha 4, Czech Republic
www.alphatechtechnologies.cz
BlueGate SIP
VoIP GSM Gate
Quick Installation guide v 1.0

2
Technical parametres
Dimensions 133 x 233 x 60 mm
Weight 850 g
Operating position various
Operating condition temperature: +5° ÷ +40°
humidity: 10% ÷ 80% při 30°
Power supply 9-15V ss or 8-12Vst, 1.5 A
VoIP
• Ethernet – 10/100Mb with standard BaseT and 100BaseTx,
connector RJ45
• SIP connection P2P or IP PBX net unit – tested with isco all
Manager, Alcatel OMNI P X, Asterisk, Nexspan, Panasonic…
• 2 VoIP channels (2 IP adresses)
• odecs: G711u, G711a, G726, GSM
• VAD (Echo cancellation)
• Protocols: IP, T P, UDP, http, TELNET, SIP, RTP
• Web server for remote management – BOA
• Software for internet phone (VoIP) – Linphone
• WEB – firmware upgrade
• WEB – interface for parametres programming IPDP
• onnection with DTMF dial in
• connection to 2 operators after time out (adjustable) for direct
dialing in
• transmit of calling part number ( LIP)
• incoming call restriction from GSM network
• outgoing call restriction to GSM network
• Priority connection through either the 1
st
or the 2
nd
GSM module (LCR
• Smart Call back – automatic incoming calls routing up CLIP
• Direct acces – assign of IP adress to GSM channels
• Echo canceller – switching ON/OFF
• volba poskytovatele GSM služeb samostatně pro každý GSM
modul
• OGM module for recording voice message*

3
• PIN protection of SIM card
GSM
• GSM 900 (class 4 – 2 W)
• GSM 1800 (class 1 – 1 W)
• Antenna connector SME/SMA, 50Ω
• SIM card: 3/1,8 V
• 2 GSM channels
Installation
Insert SIM cards.
Before SIM card inserting check their status in mobile phone (starting with
PIN or without PIN). When you want use start with PIN you have to
firstly programm this PIN to Blue Gate SIP. Without this setting the
Blue Gate SIP will not registrate to GSM network!
SIM holders will release after pressing of yellow button
SIM from bottom!

4
onnect:
GSM antennas
LAN cable Power supply –
connect at end
GSM1,2 operation (green):
LED flashing – modul registrate to
GSM net, stand by
LED lighting – connection (call)
Error status indication on channels
(RED):
LED is off – stand by
LED bliká – failure
Green LED during operation
indicates GSM modules
powering. The Red LED
indicates GSM net operation
(flashing in period 2s – stand
by, fast flashing – active
connection
).
Incoming and outgoing call via
individual IP channels

5
On P connected to LAN from which you can control connected Gateway
run various web broser. Insert IP adress of gate (default 192.168.1.250) and
you can continue in parametres setting.
STEP 1 - choosing a mode and login
It is important to choose a gate mode first. The gate can work in the
PeerToPeer mode or SIP server mode. The mode setting can be made by a
relevant switch. In the SIP server mode is possible to choose SIP server
internal or external. It can be set in a configuration interface of the gate.
In your web browser enter IP address of the gate, default is 192.168.1.2 0.
Enter user name and password. User name is admin, default password is
1234.

6
STEP 2 - language option:
Language setting can be made in a menu on the left panel.
STEP 3 - Network settings:
Network settings are located in the Network seting menu item. It is
possible to use DH P service or you can enter IP addresses manually.
After making changes click on a save and restart button.

7
Manual configuration:
Via DHCP:

8
STEP 4 - GSM gate settings
GSM gate settings can be made in a section GSM module 1 and GSM
module 2. It is important to set a customer number, which will be dialed by
the modul at an incoming calling. Next, it is important to set SIM card PIN,
if it is required. If not, write 0000. After making changes click on a save
changes button.

9
STEP - GSM gate settings in the P2P mode
The gate should be set to the P2P mode, viz. STEP 1. In this mode it is
important to set a translation of numbers into IP addresses. This setting can
be made in the Number translation section. Item „Number“ is a phone
number, IP address is an address of the selected phone. After making
changes use the save changes button.

10
STEP 6 - GSM gate settings in the SIP server mode (internal)
A module should be set to a mode with SIP server, viz STEP 1. Activation,
deactivation and a real settings of the internal SIP server can be made in the
SIP server section. After making changes use button save and restart.