Alpic Air MK010 User manual

Owner's Manual
Air Conditioners
 Thank you for choosing Air Conditioners, please read this owner’s manual carefully before operation
and retain it for future reference.If you have lost the Owner’s Manual, please contact the local agent or
www.alpicair.com for electronic version.
AlpicAir reserves the right to interpret this manual which will be subject to any change due to product
improvement without further notice.
 AlpicAir reserves the final right to interpret this manual.
Wired Controller MK010
Owner's Manual

Page 1
Gate-control Function
Working Process of Gate Control
This detection control board is only suitable for AlpicAir split type wall-mounted air conditioner with gate-
control function. The AC will run after plugging in gate-control card and stop running after plugging out
the card. Upon plugging out the card to stop the unit, the running states of the unit will be memorized.
After plugging in the card, the unit will be under standby state or resume running according to settings.
The AC will run when the customer plugs in the card and automatically stop when he plugs out the card,
which ensures unit off after leaving of persons and saves energy.
Fig.1 is about simple sketch for communication network of detection control board for AlpicAir split type
wall-mounted air conditioner series.
1 When the indoor unit hasn’t been connected to the detection control board, this air condition is the
non-gate controlled air conditioner. The air conditioner can operate at normal status.
Fig. 1 Simple Sketch for Communication Network of Detection Control Board (with Wired Controller)
for AlpicAir split type wall-mounted Hyper Nordic series air conditioner.
2.When the air conditioner has been connected to the detection control board, if the user hasn’t plug
in the gate-control card, the air conditioner will enter into standby status automatically after it has been
turned on for 6mins. When plugging in the gate-control card, air conditioner will operate normally at
the previous mode.
3.When air conditioner has been connected to the detection control board, when user operates the air
conditioner after plugging in gate-control card, the air conditioner can operate at normal status.

Page 2
4.When air conditioner has been connected to the detection control board, after plugging in gate-
control card and the air conditioner operates normally, the air conditioner will enter into standby status
automatically after plugging out the gate-control card for 6mins.
Detection Control Board Interface Sketch is shown in Fig.2
Products Parameters
Fig2 Detection Control Board Interface Sketch
①Interface connected with main board of indoor unit (3-core blue).
③Wiring terminal X2(+5V…+24V),suspended in the middle, connects with gate-control signal input.
The voltage should be about +5V to +24V.
② Wiring terminal X1(AC_L,AC_N),suspended in the middle, connects with gate-control signal input.
The voltage should be about 220V.
Note: When this detection control board is connecting to the gate-control system, it can only connect
to ②or ③.
The gate-control function can be realized after the detective interface of detection control board connects
with interface of gate-control card and signal interface of it connects with the main board.
Model: MK010
Working Voltage: AC 220-240V, 50HZ or DC +5V-+24V
Power: 1W
Working temperature: -10 --48℃

Page 3
Installation of Detection Control Board
Fig. 3 Installation Sketch of Detection Control Board
123 4
No. 1 2 3 4
Description Base box of socket installed in
the wall , a hole with( :×+×D
100mm×100mm×50mm
Bottom plate of
detection control
board
Front panel of
detection control
board
Screw M4X25
Note: Detection control board with (:×+×') 73.5mm×73.5mm×33.0mm
Fig.3 is about installation process of detection control board. The following items should be attended.
1. Installation must be performed by professionals. Either 220-240V or DC 5-24V is ok.
3. Press the bottom plate of the detection control board on the wall, and then make it and front panel of
detection control board together.
4. At last fix the bottom plate and front panel of detection control board together with screw ST2.2X6.5.
5. There shouldn’t be any large-power electric appliance and firming base nearby to avoid interference
source.
6. Avoid sunlight and rain and do not install it at wet space.
7. Do not install the unit at the place where there is corrosive gas, serious dust, salt fog and oil smoke
or which is specially wet.
8. The detection control board must be installed at concealed place and far from water and fire.
2. Cut off the power of heavy current wire covered in the mounting hole in the wall before installation.
Never perform the installation with electricity.

Cable lenght 10m Cable lenght 23cm
Standard with indoor unit.
AAC 220-240V~50/60Hz
CN1
C2
C3
Q1
CN2
R4 X1
R5
R6R7
R3
X2
DC +5V~~~+24V
R2
C1
R1
D2
U1 D1 AC - L AC - N
Door_C
CN1
C2
C3
Q1
CN2
R4 X1
R5
R6R7
R3
X2
DC +5V~~~+24V
R2
C1
R1
D2
U1 D1 AC - L AC - N
Door_C
DOOR-C
DCK
PCB Unità Interna
PCB Indoor Unit
PCB Unité intérieure
PCB Interne Einheit
PCB Unidad interior
PCB Indoor Unit
Non fornito
Not supplied
non fourni
Nicht enthalten
No suministrado
Not supplied
AC 220-240V~50/60Hz
DC 5-24V
ON-OFF Device
1
1
5-24 VDC
ON-OFF Device
23
23
220-240 VAC
CN1
C2
C3
Q1
CN2
R4 X1
R5
R6R7
R3
X2
DC +5V~~~+24V
R2
C1
R1
D2
U1 D1 AC - L AC - N
Door_C
CN1
C2
C3
Q1
CN2
R4 X1
R5
R6R7
R3
X2
DC +5V~~~+24V
R2
C1
R1
D2
U1 D1 AC - L AC - N
Door_C
DOOR-C
DCK
PCB Indoor Unit
PCB Unità Interna
PCB Indoor Unit
PCB Unité intérieure
PCB Interne Einheit
PCB Unidad interior
Not supplied
Non fornito
Not supplied
non fourni
Nicht enthalten
No suministrado
AC 220-240V~50/60Hz
DC 5-24V
ON-OFF Device
1
1
5-24 VDC
ON-OFF Device
23
23
220-240 VAC
BDC 5-24V
MK010
MK010
For each MK010 only one type of connection is possible A or B.
Page 4
Types of connection

_______________________________________________________________________________________
WWW.ALPICAIR.COM