
WARNING
~WARNING
This symbol means
important
instructions. Failure
to
heed
them
can result in serious injury
or
death.
DO
NOT
OPERATE
ANY
FUNCTION
THAT
TAKES
YOUR
ATTENTION
AWAY
FROM
SAFELY
DRIVING
YOUR
VEHICLE.
Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle in a
safe location before performing these functions.
Failure to do so may result in an accident.
KEEP
SMALL
OBJECTS
SUCH
AS
SCREWS
OUT
OF
THE
REACH
OF
CHILDREN.
Swallowing them may result in serious injury. Ifswallowed, consult a
physician immediately.
KEEP
THE
VOLUME
AT
A
LEVEL
WHERE
YOU
CAN
STILL
HEAR
OUTSIDE
NOISES
WHILE
DRIVING. ,
Excessive volume levels that obscure sounds such as emergencyvehicle
sirens or road warning signals (train crossings, etc.) can be dangerous
and may result in an accident. LISTENING
AT
LOUD VOLUME
LEVELS
IN A CAR
MAY
ALSO CAUSE HEARING DAMAGE.
DO
NOT
DISASSEMBLE
OR
ALTER.
Doing so may result in
an
accident, fire
or
electric shock.
USE
ONLY
IN
CARS
WITH A 12
VOLT
NEGATIVE
GROUND.
(Check with your dealer
if
you are
not
sure.) Failure to do so may result
in fire, etc.
USE
THE
CORRECT
AMPERE
RATING
WHEN
REPLACING
FUSES.
Failure to do so may result in fire
or
electric shock.
DO
NOT
BLOCK
VENTS
OR
RADIATOR
PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE
THIS
PRODUCT
FOR
MOBILE
12V
APPLICATIONS.
Use for other
than
its designed application may result in fire, electric
shock
or
other injury.
DO
NOT
PLACE
HANDS,
FINGERS
OR
FOREIGN
OBJECTS
IN
INSERTION
SLOTS
OR
GAPS.
Doing so may result in personal injury
or
damage to the product.
MAKE
THE
CORRECT
CONNECTIONS.
Failure to make the proper connections may result in fire
or
product
damage.
BEFORE
WIRING,
DISCONNECT
THE
CABLE
FROM
THE
NEGATIVE
BATTERY
TERMINAL.
Failure to do so may result in electric shock
or
injury due to electrical
shorts.
DO
NOT
SPLICE
INTO
ELECTRICAL
CABLES.
Never cut away cable insulation to supply power to other equipment.
Doing so will exceed the current carrying capacity
of
the wire and result
in fire
or
electric shock.
DO
NOT
DAMAGE
PIPE
OR
WIRING
WHEN
DRILLING
HOLES.
When
drilling holes in the chassis for installation, take precautions so
as not to contact, damage
or
obstruct pipes, fuel lines, tanks
or
electrical
wiring. Failure to take such precautions may result in fire.
DO
NOT
USE
BOLTS
OR
NUTS
IN
THE
BRAKE
OR
STEERING
SYSTEMS
TO
MAKE
GROUND
CONNECTIONS.
Bolts
or
nuts used for the brake
or
steering systems (or any other
safety-related system),
or
tanks should NEVER be used for installations
or
ground connections. Using such parts could disable control
of
the
vehicle and cause fire, etc.
2-EN
DO
NOT
INSTALL
IN
LOCATIONS
WHICH
MIGHT
HINDER
VEHICLE
OPERATION,
SUCH
AS
THE
STEERING
WHEEL
OR
SHIFT
LEVER.
Doing so may obstruct forward vision or hamper movement etc., and
results in serious accident.
DO
NOT
FOLLOW
ROUTE
SUGGESTIONS
IF
THE
NAVIGATION
SYSTEM
INSTRUCTS
YOU
TO
PERFORM
AN
UNSAFE
OR
ILLEGAL
MANEUVER,
OR
PLACES
YOU
IN
AN
UNSAFE
SITUATION
OR
AREA.
This product
is
not a substitute for your personal judgment. Any route
suggestions by this system should never supersede any local traffic
regulations
or
your personal judgment
or
knowledge
of
safe driving
practice.
~CAUTION
This symbol means
important
instructions. Failure
to
heed
them
can result in injury
or
material
propertydamage.
HALT
USE
IMMEDIATELY
IF
A
PROBLEM
APPEARS.
Failure to
do
so may cause personal injury
or
damage to the product.
Return it to your authorized Alpine dealer or the nearest Alpine Service
Center for repairing.
HAVE
THE
WIRING AND
INSTALLATION
DONE
BY
EXPERTS.
The wiring
and
installation
of
this unit requires special technical skill
and experience.
To
ensure safety, always contact the dealer where you
purchased this product to have the work done,
USE
SPECIFIED
ACCESSORY
PARTS
AND
INSTALL
THEM
SECURELY.
Be
sure to use onlythe specified accessory parts. Use
of
other than
designated parts may damage this unit internally,
or
may not securely
install the unit in place. This may cause parts to become loose resulting
in hazards
or
product failure.
ARRANGE
THE
WIRING
SO
IT
IS
NOT
CRIMPED
OR
PINCHED
BY
A
SHARP
METAL
EDGE.
Route the cables
and
wiring away from moving parts (like the seat rails)
or
sharp
or
pointed edges. This will prevent crimping and damage to the
wiring.
If
wiring passes through a hole in metal, use a rubber grommet
to prevent the wire's insulation from being cut by the metal edge
of
the
hole.
DO
NOT
INSTALL
IN
LOCATIONS
WITH HIGH
MOISTURE
OR
DUST.
Avoid installing the unit
in
locations with high incidence
of
moisture
or
dust. Moisture
or
dust that penetrates into this unit may result
in
product failure.
KEEP
FINGERS
AWAY
WHILE
THE
MOTORIZED
FRONT
PANEL
OR
MOVING MONITOR
IS
IN MOTION.
Failure to do so may result in personal injury or damage to the product.