Alpine MBB102 Operator's manual

MBB102
Rustic Wooden Potting Bench
with Shelves and Drawers
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, and Pond Supplies & More. All of our products are
constructed from the highest quality materials. In the event that we have not achieved our usual
standard of excellence, we will repair or replace, at our discretion, within the warranty period. A valid
proof of purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
•Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper storage
that allows water to freeze within a product may cause damage, is considered negligence,
and will not be covered under this warranty. The use of “hard water,” and/or caustic cleaners,
can affect the painted or other finishes. Failure to keep the unit clean, and use of such
additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for
some splashing to occur and protecting the immediate surfaces is not the responsibility of
Alpine Corporation.
•Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up using
standard paint. The paint is designed to protect the entire finish against breakdown of
color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading, within the first year from date of
purchase, with the above exclusion.
•Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to show
proof of purchase, provide photographs and any other information needed to validate your
claim. This may be necessary to distinguish between a partial or complete replacement of
a defective product. The warranty does not cover any items with multiple parts; the
warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department. Item is covered under one year limited warranty from the date of
purchase. When requesting replacement parts due to a warranty claim after 30 days
of purchase, credit card information will be requested for shipping charges.
•Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to:
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim.
V2.0
3

Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging. No tools are required.
Components:
A. Base Support B. Legs (2)
C. Drawer D. Shelf Divider (4)
E. Back Cover F. Top Cover
G. H2.5 Screw (4) H. H4 Screw (18)
Assembly Instructions
1. Place all the components on a flat leveled surface.
2. Take the two legs (B) and place both parallel to each other. Then take the drawer
(C) and place it in between the two legs, align it to the frame on the legs as indicated
in the diagram. To secure the drawer (C), take eight (8) H4 screws (H) and place it
on each corner of the frame on the legs as indicated in the diagram. Once in
position, turn each screw clockwise tightly. (See diagram below)
3. Take the base support (A) and place it in between the legs (B) and below the drawer
(C). To secure the base support, take four (4) H2.5 screws (G) and place one on
the top-side of each corner of the base support. Once in position, turn each screw
clockwise tightly. (See diagram below)
4. Assemble the four (4) shelf dividers by positioning two (2) vertically and the other
two (2) with chiseled corners horizontally. Then insert the vertical and horizontal
dividers together using the cut-out lines. (See diagram below)
5. Take the assembled shelf dividers and place it in between the legs (B) and on
the frames above the drawer (C). Then, take the back cover (E) and place it
behind the shelf dividers (D). Make sure to align the sides of the back cover (E)
in between both legs (B). Take six (6) H4 screws (H) and place three (3) on each
side as indicated in the diagram. Secure the back cover by turning each screw
clockwise tightly. (See diagrams below)
6. Take the top cover (F) and place it at the top of the assembled shelf, aligning its
four corners to the top of both legs (B). To secure the top cover (F), take four
(4) H4 screws (H) and place them on each corner of the top cover (F). Once in
position, turn each screw clockwise tightly. (See diagram below)
Your potting bench with shelves and drawers is now completely assembled.
Back Leg
Back Leg
Front Leg
1
2