Alpine GIL1516 User manual

GIL1516
Old Fashioned 3 Tier Garden
Tin Fountain
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed
from the highest quality materials. In the event that we have not achieved our usual standard of
excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of
purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper storage
that allows water to freeze within aproduct may cause damage and is considered negligence
and will, therefore not be covered under this warranty. The use of “hard water” and/or caustic
cleaners can affect the paint or other finishes. Failure to keep the unit clean, and use of such
additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for
some splashing to occur and protecting the immediate surfaces is not the responsibility of
Alpine Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire finish against breakdown
of color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to
show proof of purchase, provide photographs and any other information needed to
validate your claim. This may be necessary to distinguish between a partial or complete
replacement of a defective product. The warranty does not cover any items with multiple
parts; the warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department. Item is covered under one year limited warranty from the date of
purchase. When requesting replacement parts due to a warranty claim after 30 days of
purchase, credit card information will be requested for shipping charges
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim

Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging. Some splashing may occur.
Components:
Bottom Fountain Base
Back Cover
Pump
Light Cord
Transformer
Assembling:
Place the fountain on a smooth and level surface.
Connect the light cord’s 2 prongs to the cord found inside of the
fountain. (Point 1)
Connect the light cord’s single prong to the pump. (Point 2)
Connect the pump to the vinyl tubing found inside. Adjust the flow
control on the pump to the lowest setting to avoid splashing until the
fountain is completely assembled. Place the pump back into the
fountain and slide the back cover in place. (Point 3)
Connect the pump cord to the transformer. (Point 4)
Gently pour water into the fountain, being careful not to overflow and
cause splashing. Make sure the water completely submerges the pump
and the water flows smoothly during operation.
Plug the pump cord into your local power supply. Make sure that there is
no water around the plug and always keep the power source in a dry
place.
oNOTE: We recommend that you use distilled water to prevent
scale build-up. The first time you operate the pump it can take up
to 5 minutes for the air to be completely expelled and water
begins to flow properly.
Trouble Shooting & Caution
If you have any questions and/or problems, please contact the retail store you
purchased this fountain.
If your pump fails to run
Check the circuit breaker or try a different outlet to make sure the pump is
receiving electrical power.
Check the pump discharge and tubing for any kinks and/or obstructions
Any buildup obstructing the water flow can be flushed with a garden hose
Check the rotor by removing the front cover & plate to access the impellor area.
Turn the rotor and make sure that the rotor is not jammed or broken
If your pump “spews”
Check the water level to make sure the pump is completely submerged and
there if enough water in the basin to operate your fountain. Not having enough
water will cause your pump to spew
If your pump is making abnormal loud noises
Disconnect the pump from the electrical power supply and remove the front
cover & plate
Carefully grip the impeller and gently pull the impeller/rotor assembly out of the
pump housing
Rinse the impeller/rotor assembly and clean the cavity with clean water. If
breakage or damage is found, contact your local retailer for part
Fountain Care
We recommend to use Alpine’s all natural cleansing formula to eliminate foam,
lime scale and calcium buildup, fight mineral deposits, leave water crystal clear,
help prevent staining, remove organic contaminants and treat discolored water.
This formula will help prevent pump damage due to hard water build up.
i. For small sized fountains holding water up to 7liters of water, we
recommend Alpine Item # PPL100
ii. For larger sized fountains holding water over 7liters of water, we
recommend Alpine Item # PPL102
iii. For more information please visit www.alpine4u.com
Caution
oAlways unplug the pump from the electrical outlet before
cleaning & handling
oUses with clean water only, do not place the fountain and/or
parts in any other liquid.
oPeriodically change water & clean the pump to keep free
from micro-organisms
oDisconnect and store the unit in a dry place if not in use for
an extended period of time
oDo not operate with water above 90°F or 30°C
oDo not lift, carry or pull the pump by the power cord
oDo not exceed the maximum voltage & wattage on
transformer
oNEVER LET THE PUMP RUN DRY
1
3
2
4