Alpine HET100 User manual

HET100
Water Bubble Table Top
Fountain with LED Lights and
Remote
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed
from the highest quality materials. In the event that we have not achieved our usual standard of
excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of
purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper
storage that allows water to freeze within a product may cause damage and is considered
negligence and will, therefore not be covered under this warranty. The use of “hard water”
and/or caustic cleaners can affect the paint or other finishes. Failure to keep the unit clean,
and use of such additives/cleaners, will also void the warranty. Please note: for fountains,
it is normal for some splashing to occur and protecting the immediate surfaces is not the
responsibility of Alpine Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire finish against breakdown
of color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to
show proof of purchase, provide photographs and any other information needed to
validate your claim. This may be necessary to distinguish between a partial or complete
replacement of a defective product. The warranty does not cover any items with multiple
parts; the warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department.
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim

Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging.
Components:
Fountain
Stones
Spare air pump
Power Cord
Wireless Remote
Assembling:
Place the fountain on a smooth and level surface.
Fill all three cylinders full of water to the water level line. (Figure 1)
Place glass stones on the top of fountain base. (Figure 2)
Connect the power cord to the plug located on the bottom side of the
fountain. (Figure 3)
Plug the power cord into your local power supply. Make sure that there
is no water around the plug and always keep the power source in a dry
place.
This item also comes with a wireless remote controller. The sensor is
located on the bottom side of the fountain right next to the power cord
plug. (Figure 4)
If you have any questions and/or problems, please contact the retail store you
purchased this fountain.
Troubleshooting
If your LED lights stop working
You need to replace the white light adaptor box (Alpine Item# RRR126)

To replace unplug the fountain and remove the glass stones from the top
of the fountain. Then pour out all the water in the fountain. Unscrew all
three of the outer screws on the top of the fountain and remove the top.
Disconnect the white light adaptor box from both adaptors and replace.
If your bubbles stop working
Use the three air adjustors on the base top to adjust the air volume.

If the bubbles still don’t work you will need to replace the air pump (Alpine
Item# RPC116). To replace unplug the fountain and remove the glass
stones from the top of the fountan. Then pour out all the water in the
fountain. Unscrew the three screws in the center of the fountan and
remove the small circle piece. Disconnect the air tube connected to the
pump. Then unscrew all three of the outer screws on the top of the
fountain and remove the top. Disconnect the cord and remove the air
pump through the center hole. Replace the air pump.
Caution
o
Always unplug the pump from the electrical outlet before cleaning & handling
oUses with clean water only and periodically
oPeriodically change water & clean the pump to keep free from micro-
organisms
oDisconnect and drain and store the unit in a dry place if not in use for an
extended period of time
oDo not operate with water above 90°F or 30°C
oDo not lift, carry or pull the fountain by the power cord
oDo not exceed the maximum voltage & wattage on transformer
1
2
3
4
Open this hole with screw driver to replace
air pump if air pump does not work.