Alpine WIN732S User manual

Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of
products including Fountains, Birdbaths, Statuar, Pond Supplies & More. All of our products are
constructed from the highest quality materials. In the event that we have not achieved our usual
standard of excellence, we will repair or replace, at our discretion, within the warranty period. A valid
proof of purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
•Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper storage
that allows water to freeze within a product may cause damage and is considered negligence and will,
therefore not be covered under this warranty. The use of “hard water” and/or caustic cleaners can
affect the paint or other nishes. Failure to keep the unit clean, and use of such additives/ cleaners,
will also void the warranty. Please note: for fountains, it is normal for some splashing to occur and
protecting the immediate surfaces is not the responsibility of Alpine Corporation
•Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire nish against breakdown of color.
As with any product, all nishes with time will gradually fade and discolor. The warranty will only
cover against severe or complete fading within the rst year from date of purchase with the above
exclusion.
•Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you pur-
chased the product. If that is not an option, you can contactAlpine Corporation at www.alpine4u.
com. When contacting Alpine Corporation, you must be prepared to show proof of purchase, provide
photographs and any other information needed to validate your claim. This maybe necessary to dis-
tinguish between a partial or complete replacement of a defective product. The warranty does not
cover any items with multiple parts; the warranty will ONLY cover the individual component of the
unit/item that may be defective. Replacement parts can be made available to a consumer through
the original selling party, or an approved parts retailer. If this is not an option, contact our customer
service department.
•Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1.Damages caused in Transit
2.Inadequate care and/or neglect
3.Environmental and/or natural elements
4.Immersion in water, unless specied
5.Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful addi-
tives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also does
not cover any additional charges or installation, removal, disposal and/or shipping costs or conse-
quential damage associated with any warranty claim
WIN732S
Tiered Log Fountain with LED
Lights
Patent Pending
PATENT PENDING

Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been removed from the
packaging. Decide on a suitable location to begin assembling.
Parts:
1. Tiered Log Fountain (1)
2. LED Lights (1)
3. Submersible Pump (1)
4. Transformer (1)
5. Back Cover (1)
ASSEMBLY INSTRUCTIONS:
1. Remove product from the box, put base of fountain onto a at surface.
2. Wipe with a damp cloth to remove any residual dust or poly-foam.
3. Pull out the LED light cords through the side opening & connect to the transformer.
(See Diagram 1)
4. Connect the vinyl tubing into the water pump, adjust the ow control to the lowest
setting to avoid splashing until the fountain is completely assembled. Place the pump
back into the reservoir. (See Diagram 1)
5. Gently pour water into the fountain, being careful not to overow and cause splashing.
Make sure the water completely submerges the pump and the water runs smoothly
during operation. Plug pump cord into your local power supply & make sure that there
is no water around the plug & always keep the power source in a dry place. (ll the
water in the area shown in Diagram 2)
NOTE: We recommend that you use distilled water to prevent scale build-up. The rst time you
operate the pump it can take up to 5 minutes for the air to be completely expelled and water begins
to ow properly. WATER MUST BE FILLED TO SUBMERSE PUMP COMPLETELY BE-
FORE USING.
Trouble Shooting & Caution
If you have any questions and/or problems, please contact the retail store you pur-
chased this fountain.
•If your pump fails to run
• Check the circuit breaker or try a different outlet to make sure the pump is
receiving electrical power.
• Check the pump discharge and tubing for any kinks and/or obstructions
• Any buildup obstructing the water ow can be ushed with a garden hose
• Check the rotor by removing the front cover & plate to access the impellor area.
Turn the rotor and make sure that the rotor is not jammed or broken
•If your pump “spews”
• Check the water level to make sure the pump is completely submerged and there
if enough water in the basin to operate your fountain. Not having enough water will
cause your pump to spew
•If your pump is making abnormal loud noises
•Disconnect the pump from the electrical power supply and remove the front cover
& plate
• Carefully grip the impeller and gently pull the impeller/rotor assembly out of the
pump housing
• Rinse the impeller/rotor assembly and clean the cavity with clean water. If break
age or damage is found, contact your local retailer for part
•Fountain Care
•We recommend to use Alpine’s all natural cleansing formula toeliminate foam,
lime scale and calcium buildup, ght mineral deposits, leave water crystal clear,
help prevent staining, remove organic contaminants and treat discolored water.
This formula will help prevent pump damage due to hard water build up.
i.For small sized fountains holding water up to 7liters of water, we
recommend Alpine Item # PPL100
ii.For larger sized fountains holding water over 7liters of water, we
recommend Alpine Item # PPL102
iii. For more information please visit www.alpine4u.com
•Caution
o Always unplug the pump from the electrical outlet before cleaning &
handling
o Uses with clean water only, do not place the fountain and/or parts in any
other liquid.
o Periodically change water & clean the pump to keep free from
micro-organisms
o Disconnect and store the unit in a dry place if not in use for an extended
period of time
o Do not operate with water above 90°F or 30°C
o Do not lift, carry or pull the pump by the power cord
o Do not exceed the maximum voltage & wattage on transformer
o NEVER LET THE PUMP RUN DRY
u
v