Altelix NF141206-T01 User manual

IS0192 Rev A 02/09/23
Altelix LLC USA: 866-660-WIFI(9434) International: [phone] [e-mail] www.altelix.com
Copyright (C)2023 AltelixLLC. Allrights reserved. Altelixand the Altelixlogo are Trademarks and/or RegisteredTrademarks of AltelixLLC.
Specificationsare subjectto changewithout notice.See www.altelix.com for mostcurrent information
IS0192 Rev A 02/09/23
Altelix LLC USA:866-660-WIFI (9434) International: [phone] [e-mail] www.altelix.com
Copyright (C)2023AltelixLLC. All rights reserved. Altelixand the Altelixlogo areTrademarks and/or RegisteredTrademarks of Altelix LLC.
Specificationsare subjectto changewithout notice.See www.altelix.com for mostcurrent information
Note the NF141206-T01 is
shipped with the phone
jack plate removed to
facilitate wiring.
1. Remove the (4) screws
securing the aluminum
plate.
NF141206-T01 Phone Box Installation Guide
Wiring the NF141206-T01 Phone Box
Page-1
Phone Cable Gland
Phone Cable
(not included)
Mounting Plate Screws (4)
Aluminum Plate
2. Once the aluminum
plate is removed, run
your phone cable into
the box through the
cable gland.
NF141206-T01 Phone Box Installation Guide
Page-4
WARNING: INSTALLATION OF THIS PRODUCT NEAR POWERLINES IS
DANGEROUS. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS
Under some conditions, this enclosure may not prevent electrocution. Users should keep
enclosure away from any overhead wires. If enclosure contacts a power line, any initial
protection could fail at any time. IF ENCLOSURE NEARS ANY OVERHEAD WIRES,
IMMEDIATELY LET GO, STAY AWAY, AND CALL UTILITY COMPANY
THIS ENCLOSURE IS DESIGNED TO BE INSTALLED BY A LICENSED
ELECTRICIAN OR QUALIFIED INSTALLER
Warning: To avoid electric shock, grounding must be installed by the installer as part of the
installation. The unit must be grounded and installed in accordance with National Electrical
Codes (NEC) and any local codes. Note that non-metallic enclosures do not provide
grounding between conduit connections.
Warning: Enclosure must be locked when energized to prevent unauthorized access and
shock hazard.
Important: Look over the site before beginning installation, and anticipate possible
hazards. Select a safe site to install the enclosure.
If you have power lines in the area, call your local electric utility for assistance.
NEVER work alone; always have someone near who can summon help.
Check weather conditions. Be sure that the area is not slippery and make sure that rain or
thunderstorms are not predicted for the day you install the enclosure.
If you need to use a ladder, make sure it is made of non-conductive (non-metallic)
material.
Enclosures improperly installed or installed to an inadequate structure are susceptible to
wind damage that can be very serious or even life threatening. Ensure that the installation
is properly grounded. Ensure that the enclosure is properly secured and structurally sound
to support all loads (weight, wind & ice).
Rooftop Installation Warning
DO NOT assume that just because you're on a roof, you're isolated from ground. You may
still be electrocuted or fall off the roof.

IS0192 Rev A 02/09/23
Altelix LLC USA: 866-660-WIFI(9434) International: [phone] [e-mail] www.altelix.com
Copyright (C)2023AltelixLLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specificationsare subjectto changewithout notice.See www.altelix.com for mostcurrent information
IS0192 Rev A 02/09/23
Altelix LLC USA:866-660-WIFI (9434) International: [phone] [e-mail] www.altelix.com
Copyright (C)2023AltelixLLC. All rights reserved. Altelixand the Altelixlogo areTrademarks and/or RegisteredTrademarks of Altelix LLC.
Specificationsare subjectto changewithout notice.See www.altelix.com for mostcurrent information
NF141206-T01 Phone Box Installation GuidePage-3
NF141206-T01 Phone Box Installation Guide
Page-2
Pin Number Wire Lead Color
3 Black
4 Red
5 Green
6 Yellow
3. Run the phone cable behind the aluminum
plate and up through the back of the RJ11
phone jack.
Back of Phone Jack
4. Strip individual phone wires
approximately ¼” and attach to
screw terminals as shown. See
below for jack pinout:
Phone Cable
(not included)
Phone Cable
(not included)
Note: Standard telephone lines will
typically use pins 4 & 5.
Front of Phone Jack
5. Secure aluminum plate to
the enclosure using the (4)
screws ensuring phone
cable is beneath the
aluminum plate.
6. Install phone jack cover by
snapping into place.
Phone Jack Cover
Got Questions?
We are here to help.
Contact us at:
[e-mail]
USA & Canada Customers: 866-660-9434
International Customers: [phone]
Pin 4
Pin 3
Pin 5
Pin 6
Screw
Terminals
Screw
Terminals
Mounting the NF141206-T01 Phone Box
The NF141206-T01 phone box can be either wall mounted using the supplied
hardware or pole mounted using the optional NMKS-300-08 pole mounting
kit available from www.ALTELIX.com.
Mounting Feet
The (4) steel mounting feet included in the hardware kit can be
used to mount the enclosure to most surfaces.
(4) Threaded inserts are provided on the rear of the enclosure. Using
the included screws, secure the (4) mounting feet to the enclosure
as shown.