Altelix NP17AV User manual

Altelix Audio/Video Enclosures
Installation Guide

NP17AV Installation Guide
Installing a Device in the NP17AV
Page-1
The NP17AV has three adjustable brackets used for securing the equipment inside
the enclosure. The brackets can be adjusted for width, length and height
Width and Height Adjustable Brackets
Length Adjustable Mounting Bracket
The following illustration shows the minimum and maximum size devices that can
be installed inside the enclosure.
SONOS® is a trademark or registered trademark of SONOS, Inc.
IS0107 Rev A 04/05/19
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Width Length Height
Maximum Size:
9.25”(W) x 9.00”(L) x 3.50”(H)
Minimum Size:
3.00”(W) x 2.25”(L) x 0.50”(H)

Page-2
1. Position the device to be installed into the NP17AV enclosure as shown. Be sure
to orientate it so that any connections or ports are easily accessible. Once
positioned, secure the adjustable brackets to the back plate using the supplied
screws.
Mounting Brackets
Back Plate
2. Once the mounting brackets are attached to the back plate, secure the
device using the height adjustment brackets.
Height Adjustment Brackets
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Shown with Sonos Amp
Not included
Shown with Sonos Amp
Not included
SONOS® is a trademark or registered trademark of SONOS, Inc.
NP17AV Installation Guide
IS0107 Rev A 04/05/19

Page-3
Self-Adhesive Cable Tie
Wiring the NP17AV
A rubber cable grommet is provided on the enclosure which allows speaker,
Ethernet or any other types of cables to be connected to the device mounted
inside the enclosure. An internal 120VAC power outlet can be used to deliver
power to the installed device. To provide power to the enclosure, simply plug the
enclosure’s 5 foot power cord into a 120VAC outlet. Self-adhesive wire ties are
included with the NP17AV and can be attached to the back plate to help with
cable management.
5 Foot Power Cord
Cable Grommet
Outdoor Version Shown
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Shown with Sonos Amp
Not included
SONOS® is a trademark or registered trademark of SONOS, Inc.
NP17AV Installation Guide
IS0107 Rev A 04/05/19

Page-4
1. Using a ¼” drill bit, drill two holes into the rear of the enclosure at the locations
shown. Drill Locations
Mounting the NP17AV Enclosure
The NP17AV enclosure can be either wall mounted using the supplied hardware
or pole mounted using the optional NMK-0001 poll mounting kit available from
www.ALTELIX.com.
2. Using the included drilling template, place
in the desired mounting location and drill wall
as required.
3. Included with the enclosure are (4) Rubber
Bonded Washers and (4) Screws with Wall
Anchors.
4. Place Rubber Bonded
washers onto the screws
as shown.
5. (4) Holes in each corner of the metal back
plate provide access to the mounting holes in
the enclosure. When mounting, ensure the
rubber bonded washers complete cover the
enclosure mounting holes to provide a water-
tight seal.
Top of Enclosure
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Back Plate
Access Hole
Enclosure
Mounting Hole
NP17AV Installation Guide
IS0107 Rev A 04/05/19