Altelix NFC322412 Series User manual

Altelix LLC USA: 866-660-WIFI (9434) [phone] [email protected]om www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information.
IS0141-B
WARNING: READ ALL INSTRUCTION BEFORE USE. THIS ENCLOSURE IS DESIGNED TO BE
INSTALLED BY A TRAINED PROFESSIONAL INSTALLER.
NFC322412 Series RV4U NEMA Enclosure Instruction Sheet
1. Install M6 Cage Nuts into the square openings to provide an attachment point for the M6 Mounting
Screws.
a –From inside of the Mounting Rails, insert one of the flanges of the cage nut through the square opening.
Press against the side of the square opening.
b –Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square
opening. When the cage nut is properly installed, both flanges will protrude through the square opening and
will be visible on the outer surface of the mounting rail. Repeat steps 1a and 1b until all required cage nuts
are installed.
2. After installing the required cage nuts, use the included M6 Mounting Screws and M6 Washers to secure
your equipment. NOTE: The rack can hold up to 44 pounds evenly distributed.
The provided mounting feet can be used to mount the
enclosure to most surfaces or you can use the appropriate
Altelix pole or wall mount kit sold separately on our website.
To install the mounting feet, first drill through the 4 recessed
holes in the back of the enclosure. Be sure to follow proper
safety procedures when drilling. Once drilled, use the provided
M6 nuts and bolts to fasten the mounting feet to the back of
the enclosure.
Mounting Feet
Equipment Mounting

Altelix LLC USA: 866-660-WIFI (9434) [phone] [email protected]om www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information.
WARNING: INSTALLATION OF THIS PRODUCT NEAR POWERLINES IS DANGEROUS.
FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS
Under some conditions, this enclosure may not prevent electrocution. Users should keep enclosure
away from any overhead wires. If enclosure contacts a power line, any initial protection could fail at
any time. IF ENCLOSURE NEARS ANY OVERHEAD WIRES, IMMEDIATELY LET GO, STAY AWAY, AND CALL
UTILITY COMPANY
THIS ENCLOSURE IS DESIGNED TO BE INSTALLED ONLY BY A TRAINED PROFESSIONAL INSTALLER
Warning: To avoid electric shock, grounding must be installed by the installer as part of the installation.
The unit must be grounded and installed in accordance with National Electrical Codes (NEC) and any
local codes. Note that non-metallic enclosures do not provide grounding between conduit connections.
Warning: Enclosure must be secured using a pad-lock when energized to prevent unauthorized access
and shock hazard.
Important: Look over the site before beginning installation, and anticipate possible hazards.
Select a safe site to install the enclosure.
If you have power lines in the area, call your local electric utility for assistance.
NEVER work alone; always have someone near who can summon help.
Check weather conditions. Be sure that the area is not slippery and make sure that rain or
thunderstorms are not predicted for the day you install the enclosure.
If you need to use a ladder, make sure it is made of non-conductive (non-metallic) material
Enclosures improperly installed or installed to an inadequate structure are susceptible to wind
damage that can be very serious or even life threatening. Ensure that the installation is properly
grounded. Ensure that the enclosure is properly secured and structurally sound to support all
loads (weight, wind & ice).
Rooftop Installation Warning
DO NOT assume that just because you're on a roof, you're isolated from ground. You may still be
electrocuted or fall off the roof.