Altelix NP17AV-YBT2 User manual

NP17AV-YBT2
Installation Guide
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2023 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Wyebot® is a trademark or registered trademark of Wyebot, Inc.
IS0195 Rev A 06/01/23

NP17AV-YBT2 Installation Guide
Installing the WIS4200 in the NP17AV-YBT2
Page-1
The WIS4200 mounting bracket kit included with
the NP17AV-YBT2 contains (3) brackets for
securing the device into the enclosure. The (7)
screws included in the kit are used to attached
the brackets to the aluminum back plate.
Mounting Bracket Kit
1. The two adjustable brackets shown are used to secure the WIS4200 to
the back plate. Adjust the height of each bracket as shown by
loosening the two adjustment screws on each bracket.
1-7/8” 1-7/8”
Height
Adjustment
Screws
Height
Adjustment
Screws
IS0195 Rev A 06/01/23

Page-2
Back Plate
Adjustable Mounting Brackets
2. Install the two mounting brackets to the back plate as shown using the (4) #6-32
screws supplied in the kit.
Note the location of the brackets on the back plate.
3. Run Ethernet cable (not included)
into the enclosure via the cable
gland as shown.
Cable Gland
NP17AV-YBT2 Installation Guide
IS0195 Rev A 06/01/23

Page-3
4. Attach Ethernet cable to the WIS4200 and slide unit under the two adjustable
mounting brackets as shown.
Adjustable
Mounting
Brackets
5. Installed the bottom
bracket onto the back
plate as shown using (3)
#6-32 screws included in
the kit.
Bottom Bracket
NP17AV-YBT2 Installation Guide
IS0195 Rev A 06/01/23

Page-4
6. Once the WIS4200 is secured inside the enclosure, use the included cable
management straps to secure any loose cables.
Cable Management Straps
Got Questions?
We are here to help.
Contact us at:
[e-mail]
USA &Canada:866-660-9434
International: [phone]
NP17AV-YBT2 Installation Guide
IS0195 Rev A 06/01/23

Page-5
Drill Locations
Mounting the NP17AV-YBT2 Enclosure
The NP17AV-YBT2 enclosure can be either wall mounted using the supplied
hardware or pole mounted using the optional pole mounting kits available from
www.ALTELIX.com.
To wall mount the NP17AV-YBT2
enclosure, two of rear mounting feet
need to be drilled.
Using a ¼” drill bit, carefully drill
through the mounting feet in
locations shown.
3. When mounting the enclosure, ensure the rubber sealing washers completely cover
the enclosure mounting holes to provide a water-tight seal. Silicone sealant can
also be added to enhance the seal.
Mounting the Enclosure
2. Secure the enclosure
to the wall using the
(4) Screws.
1. Place (4) Rubber Sealing
Washers into (4) mounting
holes as shown.
Rubber Sealing
Washer
Mounting Hole Mounting Screw Rubber Sealing
Washer
Mounting Screws &
Wall Anchors
Rubber Sealing
Washers
Note: Back plate not shown for clarity.
NP17AV-YBT2 Installation Guide
IS0195 Rev A 06/01/23

Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2023 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
WARNING: INSTALLATION OF THIS PRODUCT NEAR POWERLINES IS DANGEROUS.
FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS
Under some conditions, this enclosure may not prevent electrocution. Users should keep enclosure away from
any overhead wires. If enclosure contacts a power line, any initial protection could fail at any time. IF ENCLOSURE
NEARS ANY OVERHEAD WIRES, IMMEDIATELY LET GO, STAY AWAY, AND CALL UTILITY COMPANY
THIS ENCLOSURE IS DESIGNED TO BE INSTALLED ONLY BY A TRAINED PROFESSIONAL
INSTALLER
Warning: To avoid electric shock, grounding must be installed by the installer as part of the installation. The unit
must be grounded and installed in accordance with National Electrical Codes (NEC) and any local codes. Note that
non-metallic enclosures do not provide grounding between conduit connections.
Warning: Enclosure must be secured using a pad-lock when energized to prevent unauthorized access and shock
hazard.
Important: Look over the site before beginning installation and anticipate possible hazards.
Select a safe site to install the enclosure.
If you have power lines in the area, call your local electric utility for assistance.
NEVER work alone; always have someone near who can summon help.
Check weather conditions. Be sure that the area is not slippery and make sure that rain or thunderstorms are not
predicted for the day you install the enclosure.
If you need to use a ladder, make sure it is made of non-conductive (non-metallic) material.
Enclosures improperly installed or installed to an inadequate structure are susceptible to wind damage that can
be very serious or even life threatening. Ensure that the installation is properly grounded. Ensure that the
enclosure is properly secured and structurally sound to support all loads (weight, wind & ice).
Rooftop Installation Warning
DO NOT assume that just because you're on a roof, you're isolated from
ground. You may still be electrocuted or fall off the roof.
IS0195 Rev A 06/01/23
NP17AV-YBT2 Installation Guide