Altronix Trove T1PDK7F24 User manual

T1PDK7F24

24 Door Kit

Fully assembled kit includes:

- Trove1 enclosure with TPD1 Altronix/PDK backplane

- One (1) eFlow104NB - Power Supply/Charger

Rev. 040419

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of this Trove kit are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Access & Power Integration

- 2 - T1PDK7F Installation Guide

Overview:

Altronix T1PDK7F24 Trove PDK kit is pre-assembled and consists of Trove1PD1 enclosure/backplane with factory installed Altronix power supply/

charger. T1PDK7F24 kit also accommodates up to three (3) PDK 8DEE modules for up to twenty-four (24) doors in a single enclosure.

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the

wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the position

of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes

over the three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent)

in desired location, opposite hinge. Slide the tamper switch bracket onto the edge

of the enclosure, approximately 2” from the right side (Fig. 1, pg. 2).

Connect tamper switch wiring to the Access Control Panel input or the

appropriate UL Listed reporting device. To activate alarm signal

open the door of the enclosure.

4. Mount PDK 8DEE modules to TPD1 backplane, refer to page 3.

5. Refer to the eFlow Power Supply/Charger Installation Guide for

further installation instructions.

Hardware:

Nylon Spacer | 5/16” Pan Head Screw | Lock Nut

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

T1PDK7F Installation Guide - 3 -

Configuration of PDK 8DEE Modules:

1. Fasten spacers (provided) to pems that match the hole pattern for PDK 8DEE modules (Fig. 2, pg. 3).

2. Mount boards to spacers utilizing 5/16” pan head screws (provided) (Fig. 2, 2a, pg. 3).

Note: PDK 8DEE modules have one (1) RJ45 jack each.

Please make sure that they are mounted correctly, as shown in Fig. 2 below.

4. Fasten TPD1 backplane to Trove1 enclosure utilizing hardware (provided).

Fig. 2

Altronix

eFlow104NB

– DC +– BAT +

L G N

PDK

8DEE

PDK

8DEE

PDK

8DEE

RJ45 Jack RJ45 Jack

RJ45 Jack

Pem

Spacer

PDK

8DEE module Backplane

Pan Head

Screw

Fig. 2a

- 4 - T1PDK7F Installation Guide

Trove1 Enclosure Dimensions (H x W x D approximate):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

4.5” (114.3mm) 4.5” (114.3mm) 2.75”

(69.9mm)

1.115” (28.3mm)

1.36” (34.5mm)

1.25” (31.8mm) 1.25” (31.8mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

4.5” (114.3mm)

13.0” (330.2mm)

0.6” (15.2mm)

14.5” (321.3mm)

1.45” (36.8mm)

7.25” (184.2mm)

1.95” (49.5mm)

1.1” (27.9mm)

0.6” (15.2mm)

0.57” (14.5mm)

18.0” (457.2mm)

1.25” (31.8mm)

Altronix is not responsible for any typographical errors.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––