Altronix Trove1BL1R User manual

Rev. TBLR102418
Trove1BL1R
- Trove rack enclosure with universal blank backplane (TBL1R)
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Access & Power Integration

- 2 - Trove1BL1R
Overview:
Altronix Trove1BL1R can be customized to accommodate various combinations of access control and power supply boards and accessories
for access control systems. TBL1R backplane is blank, which allows for ultimate flexibility in configuration.
Specifications:
Assembling and Attaching Z Bracket Wire Management Accessory (included):
Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Ten (10) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware (included)
(Fig. 1, pg. 2).
2. Attach arms to each other using bolts and
lock nuts (Fig. 1a, pg. 2).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on Fig. 1b, pg. 2.
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts (included) (Fig. 2, 2a, pg. 2).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).
Agency Listings:
• CE European Conformity.
Trove1BL1R
Trove1R rack mount enclosure with
TBL1R universal blank backplane.
• Black enclosure with ample knockouts for convenient access.
• Includes: tamper switch, cam lock.
• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.
• Dimensions (H x W x D): 3.25” x 19.0” x 26.5”
(82.6mm x 482.6mm x 673.1mm).
TBL1R
Universal blank backplane.
• 16 Gauge backplane.
• Includes mounting hardware.
• Dimensions (H x W x D): 18.5” x 15.25” x 0.05”
(469.9mm x 387.4mm x 1.3mm).
Optional Accessories:
• RE2: Rack Mount Battery Enclosure accommodates up to four (4)
12VDC/7AH batteries
• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).
• LC3: 6 ft. three-wire line cord.
Fig. 1a
Two (2)
Fig. 1
Fig. 2
Fig. 2a
Fig. 1b

Trove1BL1R - 3 -
Installation Instructions for Trove1R:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112
or equivalent) turn the enclosure upside down. Punch out the knockout in designated
location, on the back of the unit, from outside of the drawer (Fig. 3, pg. 3).
Insert the tamper switch into the knockout from outside of the drawer
with the button facing outwards and spaded connectors inside the drawer.
Connect tamper switch wiring to the Access Control Panel input or the appropriate
UL Listed reporting device. To activate alarm signal open the rack drawer.
3. Slide the Trove rack enclosure into an open 2U location in the rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the
proper fasteners.
6. Mounting Boards and Accessories to TBL1R:
a. Carefully plan the boards’ layout and mark their place(s) on backplane.
b. Drill the backplane in the marked spots using appropriate tools.
c. Attach mounting hardware for the boards and mount boards according to
their specifications.
d. Make all wire connections between boards prior to mounting backplane into
Trove rack.
e. Ensure all internal cofigurations (voltage selection, switch settings, etc.) are
completed before mounting backplane back into Trove rack enclosure.
7. After all components are mounted on the backplane, fasten backplane into Trove rack
utlizing supplied mounting hardware.
Fig. 3
Tamper Switch mounting location
Back of the drawer,
viewed from outside.

- 4 - Trove1BL1R
Trove1BL1R Enclosure Dimensions (H x W x D):
3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.
3.25”
82.3mm
26.5”
673.1mm
19” (482.6mm)
2.4”
61mm
4.57”
116.1mm
11.175” (283.8mm)
R 1.27” (32.3mm)
1” (25.4mm)
0.55” (14mm)
3.62”
92mm
0.1”
2.5mm
1.5”
38.1mm
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IITrove1BL1R L11R
MEMBER