Altronix Trove Series User manual

Overview:
Trove2KA2 accommodates various combinations of Keyscan boards with or without Altronix power supplies and accessories for
access systems.
Specifications:
Backplane Accommodates a Combination of the Following:
• Two (2) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, or eFlow104NB.
• One (1) T16100, ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6.
• One (1) CA250B, CA4500B, CA8500B, one (1) DPS-15, one (1) CIM and two (2) OCB8.
Installation Instructions for Trove2:
1. Remove backplane from enclosure prior to mounting (do not discard hardware).
2. Mark and predrill holes in the wall to line up with the top keyholes in the enclosure. Install the upper fasteners and screws in the wall
with the screw heads protruding. Place the enclosure’s upper keyholes over the screws; level and secure. Mark the position of the
lower holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the enclosure’s upper keyholes over the
upper screws. Install the lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 4).
3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 1).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount Altronix/Keyscan boards to backplane, refer to Page 2.
Hardware:
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
Enclosure
Honeywell
model # 112
Tamper Switch
or equivalent
(provided)
Fig. 1
All registered trademarks are property of their respective owners.
Trove2KA2
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane.
• Includes: tamper switch, cam lock, lock nuts and
mounting hardware.
• 16 Gauge grey enclosure with ample knockouts for
convenient access.
Enclosure Dimensions (H x W x D):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm).
TKA2
- TKA2 Altronix/Keyscan backplane.
• 16 Gauge backplane.
• Includes mounting hardware.
Dimensions (H x W x D):
25.375” x 19.375” x 0.3125” (644.6mm x 492.1mm x 7.9mm).
TKA2_Rev. 042816
Snap On Standoff | Metal Standoff
5/16” Pan Head Screw | Lock Nut
Access & Power Integration
Trove2KA2 TKA2
- Trove2 enclosure with - Altronix/Keyscan backplane only
Altronix/Keyscan backplane (TKA2)
Installation Guide

- 2 - Trove2KA2
Altronix
Power Supply
Altronix
Power Supply or
Sub-Assembly
Altronix
T16100
Metal Standoff Placement
Snap on Standoff Placement
Metal Standoff Placement
Keyscan
CA250B,
CA4500B
CA8500B
Keyscan
DPS15
Keyscan
CIM
Keyscan
OCB8
Keyscan
OCB8
Locknut
Snap on Standoff Placement
TKA2: Configuration of Altronix Power Supply
and/or Sub-Assembly Boards and Keyscan Boards
1. Fasten metal and snap on standoffs (provided) to pems which match the hole pattern for Altronix Power Supply/Chargers or Altronix
Sub-Assembly boards (Fig. 2, 2a, pg. 2). Note: Please fasten metal and snap on standoffs in the proper locations (Fig. 2, pg. 2).
2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, pg. 2).
3. Mount Altronix T16100 transformer to backplane using two locking nuts (Fig. 2, pg. 2).
4. Mount appropriate Keyscan boards into the correct positions (Fig. 2, pg. 2) by postioning standoffs over appropriate holes on the
backplane and depress down on board to secure standoff to the backplane (Fig. 2b, pg. 2).
5. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).
Fig. 2
Plastic Standoff
pre-mounted into
Keyscan modules
Insert into
TKA2 backplane
Snap on or
Metal
Standoff
Sub-Assembly
Backplane
Pem
Fig. 2a
Fig. 2b

Trove2KA2 - 3 -
7.5”
(190.5mm)
7.5”
(190.5mm)
7.5”
(190.5mm)
25.375”
(644.6mm)
19.375”
(492.1mm)
12.625”
(320.7mm)
0.45”
(11.4mm)
1.0” (25.4mm)
1.0” (25.4mm)
9.2”
(
233.7mm
)
8.5”
(215.9mm)
16.25”
(412.8mm)
0.156”
( 3.96mm)
9.2”
(
233.7mm
)
7.5”
(190.5mm)
0.45”
(11.4mm)
TKA2 Dimensions (H x W x D):
25.375” x 19.375” x 0.3125” (644.6mm x 492.1mm x 7.9mm)

- 4 - Trove2KA2
Trove2 Enclosure Dimensions (H x W x D approximate):
27.25” x 21.75” x 6.5” (692.15mm x 546.1mm x 165.1mm)
G
1.25”
(31.75mm)
1.25”
(31.75mm)
6.25”
(158.75mm)
6.25”
(158.75mm)
6.75”
(171.45mm)
8.25”
(209.54mm)
8.00”
(203.2mm)
1.5”
(38.1mm)
1.25”
(31.75mm)
0.85”
(21.59mm)
0.85”
(21.59mm)
1.00”
(25.4mm)
2.00”
(50.8mm)
1.25”
(31.75mm)
2.00”
(
50.8mm
)
2.00”
(
50.8mm
)
5.25”
(
133.35mm
)
5.25”
(
133.35mm
)
7.00”
(
177.79mm
)
2.00”
(50.8mm)
2.00”
(50.8mm)
27.00”
(685.8mm)
3.50”
(88.9mm)
0.5625”
(14.29mm)
2.415”
(61.34mm)
0.685”
(17.399mm)
1.77”
(44.96mm)
3.50”
(88.9mm)
21.50”
(546.1mm)
19.80”
(502.92mm)
5.25”
(133.35mm)
5.25”
(133.35mm)
0.885” (22.479mm)
1.125” (28.32mm)
Knockouts
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IITrove2KA2 I10R
MEMBER