Altronix NetWay Series User manual

More than just power.TM
DOC#: NetWaySPLWPX Rev. 103118
™
Embedded
Hardened Ethernet over Fiber PoE+ Switch
with Optimized Lithium Iron Phosphate
Battery Charger
Installation Guide
Models include:
NetWaySP3LWPX
- Includes one (1) Fiber Optic SFP 1G Link,
3-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates one (1) 12V LiFePO4battery.
NetWaySP4LWPX
- Includes two (2) Fiber Optic SFP 1G Links,
4-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates one (1) 12V LiFePO4battery.
NetWay4ELWPX
- Includes one (1) Fiber Optic SFP 1G Link,
4-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates one (1) 12V LiFePO4battery.
NetWaySP8LWPX
- Includes two (2) Fiber Optic SFP 1G Links,
8-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates one (1) 12V LiFePO4battery.

- 2 - NetWaySPLWPX Series
Table of Contents:
Overview .................................................................................................pg. 3
Features .......................................................................pg. 3
Configuration Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3
Enclosure Mounting and Installation...............................................pg. 4
Installation Instructions..........................................................pg. 4-5
Port Configurations .............................................................pg. 4
Recommended Altronix SFP Modules ..............................................pg. 5
Configuring Units for Network Connection .........................................pg. 5
Factory Default Settings ........................................................pg. 5
Network Settings ..............................................................pg. 5
Static .......................................................................pg. 5
DHCP.......................................................................pg. 6
Factory Reset Option ............................................................pg. 6
Typical Application Drawings
NetWaySP3LWPX ............................................................pg. 7
NetWaySP4LWPX ............................................................pg. 7
NetWay4ELWPX .............................................................pg. 8
NetWaySP8LWPX ............................................................pg. 8
Wall Mount Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 11
Pole Mounting Using Optional Pole Mount Kit ......................................pg. 11
Mechanical Drawings and Dimensions .............................................pg. 12

NetWaySPLWPX Series - 3 -
Overview:
Altronix Hardened Ethernet over Fiber PoE+ Switches with Optimized Lithium Iron Phosphate Battery Charger
provide one (1) or two (2) 1Gb SFP (Fiber) ports, three (3), four (4) or eight (8) PoE (up to 15W) or two (2) PoE+
(up to 30W) ports passing data for PoE/PoE+ compliant devices. Outputs are also configurable for a single Hi-PoE
(60W) port. These units are designed to support a single 12V LiFePO4(Lithium Iron Phosphate) battery for high
storage and charge/discharge cycle life reliability.
Features:
Input:
• 115VAC, 60Hz, 2.5A or 230VAC, 50/60Hz, 1.3A.
Power Output:
• See Configuration Chart below for output ports.
• IEEE 802.3at (30W) and IEEE 802.3af (15W)
compliant.
• 75W total power.
• Integral surge protection.
Fiber Port:
• One (1) or two (2) Gigabit SFP ports.
• Use with SFP module 1000Base-X (1Gb),
compliant to Class 1 laser product (not included).
Ethernet Ports:
• 10/100/1000 Mbps ports.
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or better structured cable.
• Distance: up to 100m.
• Speed: 10/100/1000 Mbps, half/full duplex,
auto negotiation.
Battery Backup:
• Built-in charger for 12V LiFePO4
(Lithium Iron Phosphate) battery.
Caution: Do not use lead acid or gel type batteries.
• Automatic switch over to stand-by battery
when AC fails.
LINQ Technology:
• Remote network management allows for camera/
device reset and monitoring.
• Provides local and/or remote access to critical
information via LAN/WAN.
• Email and Windows Dashboard Alert notifications
report real-time diagnostics.
• Event log tracks history.
LEDs:
• Individual PoE On LEDs for each port.
• Individual IP Link status, 10/100Base-T/active
LEDs for each port.
• ALOS LED indicates fiber connection for SFP port.
• Heartbeat LED indicates proper operation of the unit.
Applications:
• Provides PoE / PoE+ / Hi-PoE for cameras/devices.
Environmental:
• Operating Ambient Temperature:
60W: –40ºC to 75ºC (–40ºF to 167ºF);
75W: –40ºC to 70ºC (–40ºF to 158ºF);
• Relative Humidity: 85%, +/– 5%
• Storage Temperature:
–40ºC to 85ºC (–40ºF to 185ºF).
• Operating Altitude: –304.8 to 2,000m.
Mechanical:
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Accommodates one (1) 12V LiFePO4
(Lithium Iron Phosphate) battery.
• Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67”
(445.3mm x 388.6mm x 169.4mm).
• Product Weight: 15 lbs. (6.8 kg)
• Shipping Weight: 17.5 lbs. (7.9kg)
Accessories:
NetWaySP1A
• Ethernet over Fiber Media Converter/Repeater - for
applications requiring an additional SFP (Fiber) port.
P1MM
• SFP multi-mode transceiver (distances up to 550m).
P1SM10
• SFP single mode transceiver (distances up to 10km).
P1AB2K
• SFP single strand single mode transceiver kit
(distances up to 2km).
P1GCE
• SFP Copper Transceiver for use with CAT5e or
better (distances up to 100m).
PMK2
• Pole Mount Kit for outdoor enclosures.
BTL125
• 12VDC 4.5AH Lithium Iron Phosphate Battery.
Configulration Chart:
Altronix Model Number SFP Ports PoE and PoE+ Ports
(up to 30W)
Hi-PoE Ports
(up to 60W)
NetWaySP3LWPX 1 3 1
NetWaySP4LWPX 2 4 Up to 2*
NetWay4ELWPX 1 4 1
NetWaySP8LWPX 2 8 Up to 2*
*Note: Units provide a total of 75W power. Thus, at any time, only one designated port can provide full 60W
output. Please see Port Configurations (pg. 4) for details.

- 4 - NetWaySPLWPX Series
Enclosure Mounting and Installation:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. All units should be installed by a trained service personnel.
1. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.
2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings
to be used are 0.5”. Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.
3. Clean out the inside of enclosure before remounting circuit board.
4. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pg. 12):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom holes
of the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws and anchors; bolts and
locking nuts, etc.) that are compatible with mounting surface and are of sufficient length/construction to
ensure a secure mount (Fig. 9, pg. 11).
Pole Mount: Refer to Figs. 10-14, pg. 11.
5. Mount backplane in enclosure with hardware.
6. To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable.
Installation:
1. Secure cabinet to earth ground. Connect AC power from overcurrent protective
device circuit breaker (20A @ 115VAC, 60Hz; 16A @ 230VAC, 50/60Hz) to
the terminals marked [L, N] on power supply board (Fig. 1, pg. 4).
Use 14AWG or larger for all power connections (Battery, DC output, AC input).
Connect ground lug to earth or green branch wire (12AWG min.).
Keep power-limited wiring separate from non power-limited wiring by
utilizing separate knockouts/ inlets. Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before
installing or servicing equipment. There are no user serviceable parts inside.
Refer installation and servicing to qualified service personnel.
2. Port Configurations (Fig. 2, pg. 4; Fig. 6a, 7a, 8a, pg. 7-8):
NetWaySP4LWPX
Jumper
Jumper
Position
Structured Cable Ports
1234
PORT 2 30W 30W and Data –
PORT 3 30W – 30W and Data
PORT 2 60W Data Only 60W and Data –
PORT 3 60W – 60W and Data Data Only
NetWay4ELWPX
Jumper
Jumper
Position
Structured Cable Ports
1234
PORT 2 30W 30W and Data –
PORT 4 30W – 30W and Data
PORT 2 60W Data Only 60W and Data –
PORT 4 60W – Data Only 60W and Data
NetWaySP8LWPX
Jumper
Jumper
Position
Structured Cable Ports
1 2 3 4 5 6 7 8
PORT 4 30W 30W and Data –
PORT 6 30W – 30W and Data
PORT 4 60W Data Only 60W and Data –
PORT 6 60W – Data Only 60W and Data Data Only
LG N
30W 60W
PORT 2
Fig. 1
Fig. 2

NetWaySPLWPX Series - 5 -
4. Connect structured cables from port marked [Port 1], [Port 2]... on NetWaySP board to PoE compliant
cameras/edge devices (Fig. 5-8, pg. 7-8).
Note: All interconnected devices must be UL Listed.
5. Insert SFP module into port(s) marked [SFP], then connect cable to the SFP module on NetWaySP board
to the corresponding input of an SFP switch (Fig. 5-8, pg. 7-8).
6. Battery Backup (if desired): Connect one (1) 12V LiFePO4
(Lithium Iron Phosphate) battery to terminals marked [+ BAT –]
(Fig. 3, pg. 5), carefully observing polarity.
Use Altronix BTL125 12V/4.5AH Lithium Iron Phosphate battery.
Note: When battery is not used, a loss of AC will result in the
loss of output voltage.
CAUTION: Do not use lead acid or gel type batteries.
7. Please ensure that the cover is secured with security bolt.
Recommended Altronix SFP Modules:
Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily
usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.
P1AB2K - For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE - For use with CAT5e or better for distances up to 100m.
Configuring Units for Network Connection
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Please be sure to visit altronix.com for latest
firmware and installation instructions
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Factory Default Settings
• IP Address: 192.168.168.168
• User Name: admin
• Password: admin
1. Set the static IP address for the laptop to be used for programming to the same network IP address as the
NetwaySP. The default address of the NetwaySP is 192.168.168.168, E.I. 192.168.168.200.
2. Connect one end of the network cable to the network jack on the NetwaySP and the other to the network
connection of the laptop.
3. Open a browser on the computer and enter “192.168.168.168” into the address bar.
A dialog box Authentication Required will appear requesting both user name and password.
Enter the default values here. Click on the button labeled Log In.
4. The status page of the NetWaySP will appear. Click on the tab labeled Network Settings.
This will open the Network Setting screen. In this screen the MAC Address of the NetWaySP module
will be found along with the Network Settings and Email Settings.
Network Settings:
In the IP Address Method field select the method that the IP Address for the NetWaySP will be obtained
(STATIC or DHCP), then follow the appropriate steps.
Static:
A. IP Address: Enter the IP address assigned to the NetWaySP by the network administrator.
B. Subnet Mask: Enter the Subnet of the network.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
Gateway configuration is required to properly receive emails from the device.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not
encrypted and unsecure. Even though HTTP can be used for remote access, it is recommended primarily
for use with LAN connections.
E. HTTPS Port: Enter the HTTPS port number assigned to the NetWaySP module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
F. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
– DC ++ BAT –
To Stand-by
Battery
To Switch
Board
Fig. 3

- 6 - NetWaySPLWPX Series
DHCP:
A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
Next, click on the button labeled Reboot Server. After rebooting the NetWaySP will be set in the DHCP
mode. The IP address will be assigned by the router when the NetWaySP is connected to the network.
It is recommended to have the assigned IP Address reserved to ensure continued access
(see the network administrator).
B. Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP module by the network administrator
to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and
unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with
LAN connections.
Secure Network Setup (HTTPS):
In order to setup HTTPS for a Secure Network Connection, a Valid Certificate and Key must be used.
Certificates and Key should be in a “.PEM” format. Self Certifications should only be used for testing
purposes as no actual authentication is being performed. In a Self-Certified mode, the connection will still
state that it is unsecure. How to upload Certificate and Key to setup HTTPS:
1. Open Tab Labeled “Security”
2. Select Tab Labeled “Email/SSL”
3. Scroll to bottom under “SSL Settings”
4. Click “Select Certificate”
5. Browse and select valid Certificate to upload from server
6. Click “Select Key”
7. Browse and select valid Key to upload from server
8. Click “Submit Files”
Once the Certificate and Key is uploaded successfully you can proceed with setting up
HTTPS in Network Settings.
A. HTTPS Port: Enter the HTTPS port number assigned to the NetWay4E module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
B. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
Factory Reset Option:
1. Power the unit down. Allow approximately 30 seconds
for the unit to power down completely.
2. Depress Factory Reset button on NetWaySP board while
reapplying power to the unit (Fig. 4, pg. 6).
Continue holding the button until the LEDs on board go
through the start up cycle, then release the button.
3. The unit returns to the original factory settings.
Fig. 4
Factory Reset
Factory Reset
Altronix Cor
Brooklyn, NY US
www.altronix.com
NetwaySP4B

NetWaySPLWPX Series - 7 -
Typical Application:
NetWaySP3LWPX
Fig. 5
Typical Application:
NetWaySP4LWPX
Fig. 6
Note: No limit to quantity of daisy-chained units.
Daisy chaining only limited to total bandwidth of 1Gbps.
IP PoE/PoE+
or Hi-PoE Device
From Power Supply
(factory installed)
IP PoE/PoE+
or Hi-PoE Device
SFP
Spd
Spd
PoE_Data
PoE_SPR
PoE_SPR
Factory Reset
PoE_Data
Spd
Input:
48V-56VDC
PORT3 (Uplink)
Spd: 10/100/1000
PoE: 30W
Altronix Cor
Brooklyn, NY US
www.altronix.com
PORT1
Spd: 10/100/1000
PoE: 30W/60W
PORT2
Spd: 10/100/1000
PoE: 30W/60W
Link
3.3V PWR
Link
Link
+
NetwaySP3B
–
PoE
ALOS
IP PoE/PoE+
Device or NetWaySP1A
Fiber to Switch
PoE/PoE+
or Hi-PoE Device
Fiber to Switch
PoE/PoE+
or Hi-PoE Device
Factory Reset
PoE1
Altronix Corp.
Brooklyn, NY US
www.altronix.com
10/100/1000
PWR NetwaySP4B
PoE2
PORT1
1000
100
PORT3
1000
100
PORT2
PORT4
SFP2
ALOS
Input:
48V-56VDC
+–
PORT 1
PORT 2
PoE3
PoE4
PORT 3
PORT 4
PORT 2PORT 3
30W
60W
30W
60W SFP Port
SFP2
ALOS
SFP Port
Fiber to the next
Netway Spectrum
Hardened PoE Switch
60W 30W
Operation
IP PoE/PoE+
Device
IP PoE/PoE+
Device
From Power Supply
(factory installed)
Fig. 6a

- 8 - NetWaySPLWPX Series
Typical Application:
NetWay4ELWPX
Fig. 7
Typical Application:
NetWaySP8LWPX
Fig. 8
NetWay4EB
Factory Reset
PORT 1
30W
PORT 2
30W / 60W
PORT 3
30W
PORT 4
30W / 60W
SFP
+ INPUT ---
30W 60W
30W 60W
30W
60W
Operation
PORT 4
PORT 2
IP PoE/PoE+
Device
IP PoE/PoE+
Device
PoE/PoE+
or Hi-PoE Device
PoE/PoE+
or Hi-PoE Device
Fiber to Switch
From Power Supply
(factory installed)
IP PoE/PoE+ Device
IP PoE/PoE+ Device
PoE/PoE+
or Hi-PoE Device
PoE/PoE+
or Hi-PoE Device
Factory Reset
PoE1 PORTS 4, 6 = 10/100/1000
PORTS 1, 2, 3, 5, 7, 8 = 10/100
PWR
NetwaySP8B PoE3
PoE2
PORT1
1000
100
PORT3
1000
100
1000
100
1000
100
PORT2
PORT4
PORT5
PORT7 SFP2
ALOS
SFP1
ALOS
PORT6
PORT8
PoE4
PoE5
PoE7
PoE6
PoE8
Input:
48V-56VDC
+–
PORT 1
PORT 3
PORT 2
PORT 4 (1G)
PORT 4PORT 6
30W
60W
30W
60W
PORT 5
PORT 7
PORT 6 (1G)
PORT 8
SFP Port
SFP Port
60W 30W
Operation
Fiber to the next
Netway Spectrum
Hardened PoE Switch
Fiber to Switch
From Power Supply
(factory installed)
Fig. 8a
Fig. 7a
Note: No limit to quantity of daisy-chained units.
Daisy chaining only limited to total bandwidth of 1Gbps.

- 9 - NetWaySPLWPX Series
Notes:

- 10 - NetWaySPLWPX Series
Notes:

- 11 - NetWaySPLWPX Series
Wall Mount Installation
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 9, pg. 11).
Fig. 9
Pole Mounting Using Optional PMK2 Pole Mount Kit:
This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK2 outdoor pole mount kit is designed to simplify the installation of Altronix outdoor rated power supplies and
accessories housed in WP2 NEMA rated enclosures. PMK2 can be mounted on 2” to 8” (50.8mm to 203.2mm)
diameter round or 5” (127mm) square poles. Brackets are designed for use with the Wormgear Quick Release
Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 10, pg. 11).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 11, pg. 11 and Fig. 13, pg. 11).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 12, pg. 11).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket
(Fig. 10, pg. 11).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 12, pg. 11).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 11, pg. 11).
7. Clip excess straps.
Fig. 10 Fig. 11 Fig. 12
Fig. 13
Fig. 14
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 14a
5” (127mm) square pole

- 12 - NetWaySPLWPX Series
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IINetWaySPLWPX Series F17S MEMBER
FRONT VIEW COVER REMOVEDRIGHT SIDE VIEWFRONT VIEW
END VIEW
SECTION A-A
AA
316 STAINLESS STEEL
PADLOCK LATCH ATTA CHED
WITH RIVETS. Ø.375 PADLOCK EYE
17.36”
441 mm
12.00”
304.8mm
6.41”
162.8mm
10-32 X .250
BRASS INSERT
4 PLCS.
14.54” (369.3mm)
16.74”
425.2mm
0.125” (3.2mm)
14.25”
362mm
14.00” (355.6mm)
12.23” (310.6mm)
17.53”
445.3mm
16.00”
406.4mm
1.67”
42.4mm
5.00”
127mm
16.73”
425mm
15.3”
388.6mm
6.67”
169.4mm
4.94”
125.5mm
5.77”
146.6mm
0.75”
19.1mm
MOUNTING PLATE
Ø.32” (8.1mm)
WALL MOUNTING HOLE X 4
Mechanical Drawing and Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)