Altronix NetWaySP41BT Series User manual

NetWaySP41BTWP
- 4-port Hardened 802.3bt 4PPoE Switch
and Power Supply/Charger
- NEMA4/4X, IP66 rated Outdoor enclosure.
NetWaySP41BTWPX
- 4-port Hardened 802.3bt 4PPoE Switch
and Power Supply/Charger
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates up to four (4)
12VDC/4AH batteries.
NetWaySP41BTWPN
- 4-port Hardened 802.3bt 4PPoE Switch
(uses external power supply).
- NEMA4/4X, IP66 rated Outdoor enclosure.
NetWaySP41BTX
- 4-port Hardened 802.3bt 4PPoE Switch and
Power Supply/Charger
- NEMA1 rated Indoor enclosure.
NetWaySP41BTPL
- 4-port Hardened 802.3bt 4PPoE Switch
and Power Supply/Charger
- Backplane version.
NetWaySP41BTB
- 4-port Hardened 802.3bt 4PPoE Switch
- Board Only.
DOC#: NetWaySP41BT Rev. 031723 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
NetWaySP41BT Series
4-port Hardened 802.3bt
4PPoE Switches (Layer 2)
Models Include:
Fiber Solution

- 2 - NetWaySP41BT Series Installation Guide
Overview:
Altronix NetWaySP41BT Series Hardened 802.3bt 4PPoE Layer 2 Switches are equipped with two (2) 1Gb SFP
ports and four (4) 802.3bt compliant Ethernet ports rated at 90W each, limited to 240W or 320W total power,
depending on a model.
Features:
Agency Listings:
• CE European Conformity.
Input
• NetWaySP41BTWP/NetWaySP41BTWPX/
NetWaySP41BTPL/ NetWaySP41BTX:
115VAC, 60Hz, 1.8A or 230VAC, 50/60Hz, 1A.
• NetWaySP41BTB/NetWaySP41BTWPN:
48-56V UL Listed ITE power supply.
Output
• NetWaySP41BTWP/NetWaySP41BTWPX/
NetWaySP41BTPL/ NetWaySP41BTX:
Four (4) 10/100/1000 Mbps Ethernet ports rated at
90W each (limited to 240W total power).
• NetWaySP41BTB/NetWaySP41BTWPN:
Four (4) 10/100/1000 Mbps Ethernet ports rated at
90W each (depending on the power supply
employed, limited to 320W total power).
• IEEE 802.3af, 802.3at, 802.3bt compliant.
SFP Ports:
•Two (2) Gigabit SFP ports.
Ethernet Ports:
• Four (4) 10/100/1000 Mbps ports.
•Connectivity: RJ45, auto-crossover.
•Wire type: 4-pair CAT5e or higher structured cable.
•Speed: 10/100/1000 Mbps, half/full duplex,
auto negotiation.
Battery Backup:
• NetWaySP41BTWP/NetWaySP41BTWPX/
NetWaySP41BTPL/ NetWaySP41BTX:
• 24VDC charging circuit charges
LiFePO4(Lithium Iron Phosphate) or
sealed lead acid* or gel type* batteries.
• Automatic switch over to stand-by battery
when AC fails.
Indicators (LED)
•Individual PoE On LEDs for each port.
•Individual IP Link status, 10/100/1000
Base-T/active LEDs for each port.
•ALOS LED indicates fiber connection for SFP port.
•Heartbeat LED indicates proper operation of the unit.
Mechanical:
NetWaySP41BTB:
• Dimensions (L x W x D approx.):
5.625” x 4.5” x 0.625”
(158.8mm x 142.9mm x 15.9mm).
NetWaySP41BTPL:
• Dimensions (H x W x D approx.):
10.75” x 8.875” x 2.375
(273.1mm x 225.4mm x 60.3mm).
NetWaySP41BTWP, NetWaySP41BTWPN:
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59”
(338.1mm x 287.3mm x 142mm).
NetWaySP41BTWPX:
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Accommodates sealed lead acid or gel type
or LiFePO4(Lithium Iron Phosphate) 12VDC batteries*.
• Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67”
(445.3mm x 388.6mm x 169.4mm).
NetWaySP41BTX:
• NEMA1 rated indoor enclosure
• Dimensions (H x W x D approx.):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 83mm).
*CAUTION: When using lead acid or gel type batteries, enclosure must be properly ventilated.

NetWaySP41BT Series Installation Guide - 3 -
Recommended Altronix Power Sourcing Equipment:
NetWaySP4P Ethernet to Fiber Media Converter with Integral Power Supply/Charger.
Four (4) 56VDC non power-limited outputs up to 120W max. full power per port
(240W total power). Four (4) 1Gb SFP ports.
NetWaySP4PX Ethernet to Fiber Media Converter with Integral Power Supply/Charger.
Four (4) 56VDC non power-limited outputs up to 120W max. full power per port
(480W total power). Four (4) 1Gb SFP ports.
NetWaySP4P2 Ethernet to Fiber Media Converter with Integral Power-Limited Power Supply/Charger.
Four (4) 56VDC power-limited outputs up to 60W max. full power per port
(240W total power). Four (4) 1Gb SFP ports.
WayPoint562 High Current Outdoor Power Supply/Charger. 56VDC/120W output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
Vertiline563 EIA 19” 1U Rack Mountable Dual Independent Power Supply/Charger.
56VDC @ 3A each output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
PoE240 Power Supply/Charger Board. 56VD/240W output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
Recommended Altronix SFP Modules:
Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily
usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 For use with Single-Mode Fiber for distances up to 10km.
P1AB2K For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE For use with CAT5e or better for distances up to 100m.

- 4 - NetWaySP41BT Series Installation Guide
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. All units should be installed by a trained service personnel.
Mounting Instructions:
NetWaySP41BTB:
1. Mount board in the desired location/enclosure
with hardware supplied.
Note: For proper earth ground connections on
NetWaySP41BTB fasten metal spacers (provided) to
threaded studs at indicated board mounting holes
(shown on the right). This is recommended for better
environmental immunity.
2. Connect external 48V-56V UL Listed ITE power power source to terminal marked [+] and [–], carefully
observing correct polarity (Fig. 2, pg. 6).
NetWaySP41BTWPN/NetWaySP41BTWP/NetWaySP41BTWPX:
1. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.
2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings
to be used are 0.5”. Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable.
3. Clean out the inside of enclosure before remounting circuit boards/backplane.
4. NetWaySP41BTWPN: Connect external 48V-56V UL Listed ITE power power source to terminal marked
[+] and [–], carefully observing correct polarity (Fig. 2, pg. 6).
5. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pg. 11-12):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom
hole of the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws
and anchors; bolts and locking nuts, etc.) that are compatible with mounting surface and
are of sufficient length/construction to ensure a secure mount (Fig. 4, pg. 8).
Pole Mount: Refer to Fig. 5 - 9, pg. 8.
6. Mount backplane in enclosure with hardware.
NetWaySP41BTX:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two (2) upper fasteners and screws in the wall with the screw heads protruding.
Place the enclosure’s upper keyholes over the two (2) upper screws; level and secure. Mark the position of
the lower two (2) holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the
enclosure’s upper keyholes over the two (2) upper screws. Install the two (2) lower screws and make sure
to tighten all screws (Enclosure Dimensions, pg. 9). Secure enclosure to earth ground.
NetWaySP41BTPL:
1. Mount backplane in the desired enclosure with hardware supplied (Backplane Dimensions, pg. 10).
Power Connection:
For NetWaySP41BTWP, NetWaySP41BTWPX, NetWaySP41BTX, and NetWaySP41BTPL:
1. Secure cabinet to earth ground. Connect AC power from overcurrent protective device circuit breaker
(20A @ 115VAC, 60Hz, 16A @ 230VAC, 50/60Hz) to the terminals marked [L, N] on power supply board
(Fig. 3, pg. 7). Use 14AWG or larger for all power connections (Battery, DC output, AC input).
Connect ground lug to earth or green branch wire (12AWG min.).
Keep power-limited wiring separate from non power-limited wiring by utilizing separate knockouts/
inlets. Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing
equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified
service personnel.
NetWaySP41BTB
Altronix Corp.
Brooklyn, NY US
www.altronix.com
Input:
48V-56VDC
+–
PoE3
PoE4
PORT 4
Metal Spacers
Fig. 1

NetWaySP41BT Series Installation Guide - 5 -
Input/Data Connections:
1. Connect structured cables from port marked [Port 1] to [Port 4] on NetWay unit to PoE compliant
cameras/edge devices (Fig. 2, pg. 6).
2. Insert SFP module into port(s) marked [SFP], then connect cable to the SFP module on NetWaySP41BTB to
the corresponding input of an SFP switch (Fig. 2, pg. 6).
Battery Backup (if desired):
NetWaySP41BTWP/ NetWaySP41BTWPX/NetWaySP41BTX/NetWaySP41BTPL:
1. Connect two (2) 12VDC batteries wired in series or one (1) 24V battery to terminals marked [– BAT +]
(Fig. 3, pg. 7), carefully observing polarity. When use of stand-by batteries is desired, they can be LiFePO4
(lithium iron phosphate), lead acid or gel type.
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
Note: When using two 12V LiFePO4(lithium iron phosphate) batteries, check with manufacturer
specifications that batteries can be connected in series.
For outdoor battery backup, battery enclosure must have sufficient ventilation.
Security:
Please ensure that the cover is secured with:
Key lock and screws for NetWaySP41BTX, Security Bolt for NetWaySP41BTWP(X) and NetWaySP41BTWPN.
Technical Specifications:
Parameter Description
Number of
Ports
Four (4) 10/100/1000 Mbps Ethernet ports rated at 90W each.
IEEE 802.3af, 802.3at, 802.3bt compliant. Two (2) Gigabit SFP Ports.
Input Power
Requirements
NetWaySP41BTWP/NetWaySP41BTWP/NetWaySP41BTPL/NetWaySP41BTX:
115VAC, 60Hz, 1.8A or 230VAC, 50/60Hz, 1A.
NetWaySP41BTB/NetWaySP41BTWPN: 48-56V UL Listed ITE power supply.
Environmental
Conditions
Operating Ambient Temperature:
240W: – 40ºC to 55ºC (– 40ºF to 131ºF)
180W: – 40ºC to 65ºC (– 40ºF to 149ºF)
150W: – 40ºC to 75ºC (– 40ºF to 167ºF)
Relative Humidity: 85%, +/– 5%
Storage Temperature: – 30ºC to 85ºC (– 22ºF to 185ºF)
Operating Altitude: – 304.8 to 2,000m
Weights
(approx.)
Model Product Weight Shipping Weight
NetWaySP41BTWP
NetWaySP41BTWPX
NetWaySP41BTWPN
NetWaySP4X
NetWaySP4PL
NetWaySP41BTB
10.5 lb. (4.76 kg)
15 lb. (6.8 kg)
9.5 lb. (4.3 kg)
6.85 lb. (3.11 kg)
2.6 lb. (1.18 kg)
0.4 lb. (0.18 kg)
11.9 lb. (5.4 kg)
17.5 lb. (7.9kg)
10.9 lb. (4.9 kg)
7.75 lb. (3.51 kg)
4.0 lb. (1.81kg)
0.75 lb. (0.34 kg)

- 6 - NetWaySP41BT Series Installation Guide
Fig. 2 - NetWaySP41BTB/NetWaySP41BTWPN – Typical Application with Composite Cable
Powering Cable Distance Chart
Power
Requirements
Power
Cabling
AWG
Maximum
Distance (ft./m)
Power
Requirements
Power
Cabling
AWG
Maximum
Distance (ft./m)
15W 12/2 11,162’ / 3,403m 15W 16/2 4,415’ / 1,346m
30W 12/2 5,581’ / 1,702m 30W 16/2 2,207’ / 673m
45W 12/2 3,767’ / 1,148m 45W 16/2 1,490’ / 454m
60W 12/2 2,739’ / 835m 60W 16/2 1,083’ / 330m
75W 12/2 2,249’ / 686m 75W 16/2 889’ / 271m
90W 12/2 1,872’ / 571m 90W 16/2 740’ / 226m
105W 12/2 1,607’ / 490m 105W 16/2 635’ / 194m
120W 12/2 1,408’ / 429m 120W 16/2 557’ / 170m
180W 12/2 180W 16/2
Estimated distances based on starting voltage of 56VDC and accounts for a 10 volt drop.
All distances are per IEEE 802.3at standard for device power requirements of minimum 44VDC and leave an
approximate 2 volts for safety and exibility.
Carefully
observe
polarity
Fiber to the next
Netway Spectrum
Hardened PoE Switch
PoE1
Altronix Corp.
Brooklyn, NY US
www.altronix.com
PWR NetwaySP41BTB
PoE2
PORT1
1000
100
PORT3
1000
100
PORT2
PORT4 SFP2
ALOS
Input:
48V-56VDC
+–
PORT 1
PORT 2
PoE3 PoE4
PORT 3
PORT 4
SFP Port
SFP2 ALOS
SFP Port
Carefully observe polarity
Composite
Cable
48-55V UL Listed
ITE Power Supply
Fiber Switch
IEEE 802.3bt
PoE/PoE+/Hi-PoE
Device
IEEE 802.3bt
PoE/PoE+/Hi-PoE
Device
PoE/PoE+,
Hi-PoE or
BT Device

NetWaySP41BT Series Installation Guide - 7 -
Fig. 3 - NetWaySP41BTX/NetWaySP41BTWP/NetWaySP41BTWPX/NetWaySP4BL –
Typical Application with Factory Installed Power Supply
Fiber to the next
Netway Spectrum
Hardened PoE Switch Fiber to Switch
PoE1
Altronix Corp.
Brooklyn, NY US
www.altronix.com
PWR NetwaySP41BTB
PoE2
PORT1
1000
100
PORT3
1000
100
PORT2
PORT4 SFP2
ALOS
Input:
48V-56VDC
+–
PORT 1
PORT 2
PoE3 PoE4
PORT 3
PORT 4
SFP Port
SFP2 ALOS
SFP Port
IEEE 802.3bt
PoE/PoE+/Hi-PoE
Device
IEEE 802.3bt
PoE/PoE+/Hi-PoE
Device
PoE/PoE+,
Hi-PoE or
BT Device
115/230VAC
Input
LGN
5A 250VA
– DC 56V +– BAT 24V +
To 24V Stand-by
Batteries

- 8 - NetWaySP41BT Series Installation Guide
Wall Mount Installation
1. Place unit at desired location and secure with mounting
screws (not included) (Fig. 4, pg. 8).
Fig. 4
Pole Mounting Using Optional Pole Mount Kit
PMK1 (NetWaySP41BTWP) or PMK2 (NetWaySP41BTWPX):
This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK1 and PMK2 outdoor pole mount kits are designed to simplify the installation of Altronix outdoor rated
power supplies and accessories housed in models WP1, WP2, WP3 and WP4 NEMA rated enclosures. PMK1
and PMK2 can be mounted on 2” to 8” (50.8mm to 203.2mm) diameter round or 5” (127mm) square poles.
Brackets are designed for use with the Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 5, pg. 8).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 6, pg. 8 and Fig. 8, pg. 8).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 7, pg. 8).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket
(Fig. 5, pg. 8).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 7, pg. 8).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 5, pg. 8).
7. Clip excess straps.
Fig. 5 Fig. 6 Fig. 7
Fig. 8
Fig. 9
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 9a
5” (127mm) square pole

NetWaySP41BT Series Installation Guide - 9 -
NetWaySP41BTX
Mechanical Drawing and Dimensions (H x W x D approx.):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)

- 10 - NetWaySP41BT Series Installation Guide
NetWaySP41BTPL
Mechanical Drawing and Dimensions (H x W x D approx.):
10.75” x 8.875” x 2.375” (273.1mm x 225.4mm x 60.3mm)
10.75” (273.1mm) 10.25” (260.3mm)
8.875” (225.4mm)
8.25” (209.5mm)
0.25” (6.4mm)

NetWaySP41BT Series Installation Guide - 11 -
NetWaySP41BTWP and NetWaySP41BTWPN
Mechanical Drawing and Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59” (338.1mm x 287.3mm x 142mm)
5.59” (142mm)
PADLOCK LATCH ATTACHED
WITH RIVETS (Ø 0.375” (9.5mm) PADLOCK EYE)
Ø 0.32 (8.1mm)
MOUNTING HOLE
TYP. 4 PLACES
8.00” (203.2mm)
STAINLESS STEEL PIANO HINGE
10.75” (273.1mm)
10.00” (254mm)
8.25” (209.6mm)
10.25” (260.4mm)
12.00” (304.8mm)
13.50” (342.9mm)
10-32 X 0.25” (6.4mm)
BRASS INSERT (X2)
1.61” (40.9mm)
3.96” (100.6mm)
12.75” (323.9mm)
11.31” (287.3mm)
13.31” (338.1mm)
10-32 X 0.375” (9.5mm)
BRASS INSERT (X4)
FRONT VIEW
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEW
END VIEW

- 12 - NetWaySP41BT Series Installation Guide
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEWFRONT VIEW
END VIEW
SECTION A-A
AA
316 STAINLESS STEEL PADLOCK LATCH
ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE
17.36” (441 mm)
12.00” (304.8mm)
6.41” (162.8mm)
10-32 X 0.250 BRASS INSERT 4 PLCS.
14.54” (369.3mm)
16.74” (425.2mm)
0.125” (3.2mm)
14.25” (362mm)
14.00” (355.6mm)
12.23” (310.6mm)
17.53” (445.3mm)
16.00” (406.4mm)
1.67” (42.4mm) 5.00” (127mm)
16.73” (425mm)
15.3” (388.6mm)
6.67” (169.4mm)
4.94” (125.5mm)
5.77” (146.6mm)
0.75” (19.1mm)
MOUNTING PLATE
Ø 0.32” (8.1mm)
WALL MOUNTING HOLE X 4
NetWaySP41BTWPX
Mechanical Drawing and Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IINetWaySP41BT Series C17W MEMBER