Alvarion BreezeACCESS II User manual

Radio
Frequency 2.4GHz ISM band
Radio Access Method FHSS CSMA/CA
Operation Mode Time Division Duplex
Standards ETSI ETS 300 328, FCC Part 15
Channel Bandwidth 1MHz
Output Power (at antenna port) SU-ID, AU-ID: 17dBm, 10dBm (ETSI)
SU-R: 26dBm (FCC)
SU-A/E, AU-A/E: 26dBm (HP) or 2dBm (LP), Control Range 20dB typical.
Antenna SU-A: 15dB, 20˚
AU-A: 16.5dBi, 60˚
Sensitivity Data Rate SU-ID, AU-ID SU-R SU-A/E, AU-A/E
(dBm at antenna port, BER 1E-6) 1 Mbps -81 -86 -87
2 Mbps -74 -80 -81
3 Mbps -66 -71 -73
Data Rate 3 Mbps max.
Modulation Multilevel GFSK
Outdoor Unit to Indoor Unit Communication
Intermediate Frequency (IF) 440MHz
IF Cable Impedance 50 ohm
Maximum IF cable Attenuation 15dB
Maximum IF cable DC Resistance 1.5 ohm
Voice Communication (DV series)
Protocol H.323 Voice over IP compliant
Compression G.723 6.3Kbps compression, G.729 8Kbps compression, G.711 64Kbps transparent
Echo Cancellation G.168, G.131
Configuration and Management
Local Management Via MON port, Monitor program using terminal emulation
Remote Management SNMP, Telnet, TFTP
Remote Management Access From the wired LAN or from the wireless link
SNMP agents MIB II, Bridge MIB, BreezeACCESS Private MIBs
Accounting Radius compatible client in subscriber units
Security Authentication, Filtering and Virtual LAN
Software upgrade TFTP download
Interfaces
RF (antenna) AU-ID, SU-ID: 2 x SMA jacks
AU-RE, SU-RE: N-Type jack, lightning protected
IF AU-RA/RE, SU-RA/RE outdoor units: TNC jack, lightning protected
SU-NI, AU-NI, BS-AU indoor units: TNC jack, lightning protected
Ethernet Indoor units: 10BaseT,(RJ 45) with 2 embedded LEDs
Telephone (DV series) RJ 11 (POTS)
Monitor Indoor units: 3-pin low profile
Power AU-RA/RE, SU-RA/RE outdoor units: 12VDC via the IF cable
SU-NI, AU-NI indoor units, SU-ID, AU-ID: DC power plug to the external power supply
BS-PS (Power Supply module of BS-SH): 4-pin DC power plug to a –48VDC power source
BS-PS-AC (Power Supply module of BS-SH-AC): 3-pin AC power plug to a 110/220VAC
power source
Electrical
SU-ID-xD (data only), AU-ID 5VDC / 1.5A from the external power supply
(supplied with the unit), 100-250 VAC, 47-63 Hz
SU-A/E, AU-A/E-NI, 12VDC / 2.5A from the external power supply
(supplied with the unit), 100-240 VAC, 47-63 Hz
BS-SH (modular base station shelf) -48VDC or 110/220 VAC, 200W for a fully equipped shelf.
25W each AU (outdoor unit plus indoor module)
Mechanical
SU-ID, AU-ID 13cm x 8.6cm x 3cm, 0.5 kg.
SU-RA 30cm x 30 cm x 7.2 cm, 3 kg.
AU-RE, SU-RE 30cm x 12 cm x 5 cm, 2.2 kg.
SU-NI, AU-NI 13cm x 8.6cm x 3cm, 0.5kg.
BS-SH 19”, 3U, depth 26cm, 6 kg. fully loaded
Environmental
Operating Temperature Indoor units and modules: 0˚C to 40˚C
Outdoor units: -40˚C to 60˚C
Operating Humidity 5% to 95% non-condensing. Outdoor units are weather protected.
Standards Compliance General
EMC EN 300-385, FCC Part 15
Safety EN 60950, UL 1950
Environmental ETS 300 019
811072 Rev.d
We're on your wavelength.
Affordable freedom
BreezeACCESS II is the ideal broadband wireless access system for
service providers operating in the unlicensed 2. GHz ISM band.
As a wireless alternative to wired access networks, BreezeACCESS II
leverages Frequency Hopping Spread Spectrum technology in Time
Division Duplex (TDD) mode to deliver reliable broadband data services,
reaching remote locations and bypassing unusable copper.
BreezeACCESS II provides an instant and independent infrastructure,
which is immediately deployable with lower infrastructure construction
and operating costs than any other solution on the market.
Specifications
BreezeACCESS™ II
We're on your wavelength.
www.alvarion.com
International Corporate
Headquarters
Tel: [phone]
Fax: [phone]
Email: [email protected]
North America Headquarters
Tel: [phone]
Fax: [phone]
Email: [email protected]
Latin America Caribbean
Tel: [phone]
Fax: [phone]
Email: [email protected]
Brazil
Tel: [phone]
Fax: [phone]
Email: [email protected]
China
Tel: [phone]
Fax: [phone]
Email: [email protected]
Czech Republic
Tel: [phone]
Fax: [phone]
Email: [email protected]
France
Tel: [phone]
Fax: [phone]
Email: [email protected]
Germany
Tel: [phone]
Fax: [phone]
Email: [email protected]
Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
Mexico
Tel: [phone]
Fax: [phone]
Email: [email protected]
Romania
Tel: [phone]
Fax: [phone]
Email: [email protected]
Russia
Tel: [phone]
Fax: [phone]
Email: [email protected]
U.K. Ireland
Tel: [phone]
Fax: [phone]
Email: [email protected]
Uruguay
Tel: [phone]
Fax: [phone]
Email: [email protected]
© Copyright 2004 Alvarion Ltd. All rights reserved.
Alvarion, BreezeCOM, WALKair, WALKnet, BreezeNET, BreezeMANAGE, BreezeACCESS, BreezeLINK, BreezePHONE, MGW, eMGW and/or
other products and/or services referenced here in are either registered trademarks, tradenames or service marks of Alvarion Ltd.
All other names are or may be the trademarks of their respective owners.
The content herein is subject to change without further notice.

BreezeACCESS II Base Station Equipment -
Core technology elemental strength
BreezeACCESS II provides a Base Station and three types of Access
Units, delivering superior flexibility in architecture and network
deployment.
All Access Units are connected to the subscriber's data equipment
via a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface.
Base Station Shelf
The 19" Base Station shelf
(BS-SH) can hold up to six
BS-AU modules, providing
reliable access to maximum
numbers of subscribers.
The BS-AU modules can be synchronized to ensure optimal utilization
of the available frequency spectrum.
In addition, the Base Station shelf includes up to two redundant power
supply modules, which are served by either a -48 VDC or a 110/220
VAC power source.
A GPS synchronization system allows accurate synchronization of
BreezeACCESS base stations located on different sites.
Indoor/Outdoor Access Units
The BreezeACCESS II indoor/outdoor
Access Unit configuration includes
an indoor module and outdoor unit
that contains the radio and antenna
units. Data, power, management
and control signals are transmitted
from the indoor unit to the outdoor
unit via a coaxial cable.
The indoor/outdoor Access Units are available
with either 26dBm (HP-High Power) or 2dBm (LP-Low Power)
output power at the antenna port.
The outdoor units feature two antenna options, as follows:
•AU-A-BS units: Comprise an indoor module and outdoor unit,
which contains a radio unit and integrated panel antenna.
•AU-E-BS units: Feature an indoor module and outdoor unit,
which contains a radio unit and an RF connector for a separate
external antenna.
Miniature Indoor Access Units
Optimized for indoor installations, the miniature
indoor units are designed to fit on a desktop
or mounted on the wall and are powered from
the mains (100-250 VAC).
The indoor Access Units (AU-ID) include two RF connectors for
detached diversity antennas.
Stand-Alone "Micro Cell" Access Units
The Micro Cell Access Units are stand-alone modules that connect
to the same outdoor units as described in the Indoor/Outdoor
Access Units configuration. The indoor units are designed to fit
on a desktop or mount on the wall and are powered from the
mains. Data, power, management and control signals are transmitted
from the indoor unit to the outdoor unit via a coaxial cable.
The outdoor units feature two antenna options, as follows:
•AU-A-NI units: Comprise an indoor module and outdoor unit,
which contains a radio unit and integrated antenna.
•AU-E-NI units: Feature an indoor module and outdoor unit,
which contains a radio unit and an RF connector for a separate
external antenna.
Demand-based build-out, easy installation and low cost
of ownership enables rapid market penetration, increased
subscription and enhanced value-added services.
Packet switching technology optimized for IP-based
applications and ”always on” connectivity.
Frequency Hopping Spread Spectrum (FHSS) radio
technology provides unlimited cell overlay capacity and
seamless integration between cells, eliminating capacity
planning or performance degradation when adding new
subscribers. In addition, FHSS is not susceptible to
interference from other technologies operating in the
same 2. GHz ISM band
Adaptive Circuit Switched Emulation (ACSE) air protocol
maintains the efficiency of IP transmission, while reserving
specific time slots for active voice call traffic.
Fast packet-based data transmission and toll quality for
delay and jitter sensitive telephony.
Highly cost effective infrastructure and customer premises
equipment.
Toll quality voice with integrated RJ11 voice ports in
subscriber units.
Advanced telephony features when used in conjunction
with a V5.1 gateway.
802.1P enables delay sensitive traffic to be prioritized in
the network.
802.1Q VLANs separate traffic into virtual private networks.
Independent uplink/downlink transmission settings for
CIR/MIR, enabling assured and differentiated QoS.
Carrier grade features including a rack mount chassis
base station with redundancy, hot swap capability and
UPS facilities.
Easy-to-use SNMP-based remote management system,
enabling simple unit configuration and multiple
simultaneous unit upgrading.
Product Highlights BreezeACCESS II System Components
BreezeACCESS II CPEs - Equipped to perform
The BreezeACCESS II series of Customer Premises Equipment
(CPE) features both data plus voice and data-only capabilities.
The BreezeACCESS II family of CPEs comprises two types of
subscriber unit configuration options, which enable service
providers to optimize their network architecture for greater
subscriber reach and satisfaction.
Both indoor and indoor/outdoor configuration options connect
to the subscriber's data equipment via a standard IEEE 802.3
Ethernet 10-BaseT (RJ 45) interface. Telephony services are
supported using a standard POTS (RJ 11) interface connected
directly to the subscriber's telephone.
Miniature Indoor Units
Optimized for indoor installations, the miniature
indoor units are designed to fit conveniently
on a desktop or mounted easily on the wall.
BreezeACCESS provides SU-ID or SU-R units
that feature two RF connectors for detached diversity antennas.
Indoor/Outdoor Units
The BreezeACCESS II indoor/outdoor option includes an indoor
desktop or wall-mountable unit and an outdoor antenna and
radio unit.
Data, power, management and control signals are transmitted
from the indoor unit to the outdoor unit via a coaxial cable.
The outdoor units feature two antenna options, delivering
enhanced network flexibility, as
follows:
• SU-A units: Comprise a radio
module and integrated flat panel
antenna.
• SU-E units: Include a radio
module and RF connector for a
separate external antenna.
Both types of outdoor units are
available with either 26dBm (HP-High Power) or 2dBm (LP-Low
Power) output power at the antenna port.
Subscriber units are available with single telephone line support
Unrestricted access unlimited choice.
BreezeACCESS II
BreezeACCESS II delivers a
comprehensive range of product
features, ensuring fast, consistent and
reliable data and voice service, including
Product Type Product Name Product Description
Miniature Indoor SU-ID-1D-2.4 Detached antenna - 1 data user
Subscriber Units SU-ID-BD-2.4 Detached antenna - full bridge
SU-R-1D-2.4 Detached antenna - 1 data user
SU-R-BD-2.4 Detached antenna - full bridge
Subscriber Units SU-A-1D-2.4 Integrated antenna - 1 data user
with an Outdoor SU-E-1D-2.4 Detached antenna - 1 data user
Radio Unit SU-A-BD-2.4 Integral antenna - full bridge
SU-E-BD-2.4 Detached antenna - full bridge
Product Type Product Name Product Description
Base Station Shelf BS-SH Base station chassis with
one DC power supply
BS-SH-AC Base station chassis with
one AC power supply
Outdoor Access AU-A-BS-2.4 Includes base station module and
Units for use outdoor unit with integrated antenna
with Base Station AU-E-BS-2.4 Includes base station module and
outdoor unit with connectors for
external antenna
Stand-alone AU-E-NI-2.4 Includes indoor unit and outdoor unit
Access Point with connectors for external antenna
Power Supply BS-PS Base station DC power supply
BS-PS-AC Base station AC power supply
GPS GU-A-BS Includes synchronization
Synchronization card and outdoor GPS radio
System unit with integrated antenna
SU-A-BD
SME/SOHO Residential
SU-A-1D1V

BreezeACCESS II Base Station Equipment -
Core technology elemental strength
BreezeACCESS II provides a Base Station and three types of Access
Units, delivering superior flexibility in architecture and network
deployment.
All Access Units are connected to the subscriber's data equipment
via a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface.
Base Station Shelf
The 19" Base Station shelf
(BS-SH) can hold up to six
BS-AU modules, providing
reliable access to maximum
numbers of subscribers.
The BS-AU modules can be synchronized to ensure optimal utilization
of the available frequency spectrum.
In addition, the Base Station shelf includes up to two redundant power
supply modules, which are served by either a -48 VDC or a 110/220
VAC power source.
A GPS synchronization system allows accurate synchronization of
BreezeACCESS base stations located on different sites.
Indoor/Outdoor Access Units
The BreezeACCESS II indoor/outdoor
Access Unit configuration includes
an indoor module and outdoor unit
that contains the radio and antenna
units. Data, power, management
and control signals are transmitted
from the indoor unit to the outdoor
unit via a coaxial cable.
The indoor/outdoor Access Units are available
with either 26dBm (HP-High Power) or 2dBm (LP-Low Power)
output power at the antenna port.
The outdoor units feature two antenna options, as follows:
•AU-A-BS units: Comprise an indoor module and outdoor unit,
which contains a radio unit and integrated panel antenna.
•AU-E-BS units: Feature an indoor module and outdoor unit,
which contains a radio unit and an RF connector for a separate
external antenna.
Miniature Indoor Access Units
Optimized for indoor installations, the miniature
indoor units are designed to fit on a desktop
or mounted on the wall and are powered from
the mains (100-250 VAC).
The indoor Access Units (AU-ID) include two RF connectors for
detached diversity antennas.
Stand-Alone "Micro Cell" Access Units
The Micro Cell Access Units are stand-alone modules that connect
to the same outdoor units as described in the Indoor/Outdoor
Access Units configuration. The indoor units are designed to fit
on a desktop or mount on the wall and are powered from the
mains. Data, power, management and control signals are transmitted
from the indoor unit to the outdoor unit via a coaxial cable.
The outdoor units feature two antenna options, as follows:
•AU-A-NI units: Comprise an indoor module and outdoor unit,
which contains a radio unit and integrated antenna.
•AU-E-NI units: Feature an indoor module and outdoor unit,
which contains a radio unit and an RF connector for a separate
external antenna.
Demand-based build-out, easy installation and low cost
of ownership enables rapid market penetration, increased
subscription and enhanced value-added services.
Packet switching technology optimized for IP-based
applications and ”always on” connectivity.
Frequency Hopping Spread Spectrum (FHSS) radio
technology provides unlimited cell overlay capacity and
seamless integration between cells, eliminating capacity
planning or performance degradation when adding new
subscribers. In addition, FHSS is not susceptible to
interference from other technologies operating in the
same 2. GHz ISM band
Adaptive Circuit Switched Emulation (ACSE) air protocol
maintains the efficiency of IP transmission, while reserving
specific time slots for active voice call traffic.
Fast packet-based data transmission and toll quality for
delay and jitter sensitive telephony.
Highly cost effective infrastructure and customer premises
equipment.
Toll quality voice with integrated RJ11 voice ports in
subscriber units.
Advanced telephony features when used in conjunction
with a V5.1 gateway.
802.1P enables delay sensitive traffic to be prioritized in
the network.
802.1Q VLANs separate traffic into virtual private networks.
Independent uplink/downlink transmission settings for
CIR/MIR, enabling assured and differentiated QoS.
Carrier grade features including a rack mount chassis
base station with redundancy, hot swap capability and
UPS facilities.
Easy-to-use SNMP-based remote management system,
enabling simple unit configuration and multiple
simultaneous unit upgrading.
Product Highlights BreezeACCESS II System Components
BreezeACCESS II CPEs - Equipped to perform
The BreezeACCESS II series of Customer Premises Equipment
(CPE) features both data plus voice and data-only capabilities.
The BreezeACCESS II family of CPEs comprises two types of
subscriber unit configuration options, which enable service
providers to optimize their network architecture for greater
subscriber reach and satisfaction.
Both indoor and indoor/outdoor configuration options connect
to the subscriber's data equipment via a standard IEEE 802.3
Ethernet 10-BaseT (RJ 45) interface. Telephony services are
supported using a standard POTS (RJ 11) interface connected
directly to the subscriber's telephone.
Miniature Indoor Units
Optimized for indoor installations, the miniature
indoor units are designed to fit conveniently
on a desktop or mounted easily on the wall.
BreezeACCESS provides SU-ID or SU-R units
that feature two RF connectors for detached diversity antennas.
Indoor/Outdoor Units
The BreezeACCESS II indoor/outdoor option includes an indoor
desktop or wall-mountable unit and an outdoor antenna and
radio unit.
Data, power, management and control signals are transmitted
from the indoor unit to the outdoor unit via a coaxial cable.
The outdoor units feature two antenna options, delivering
enhanced network flexibility, as
follows:
• SU-A units: Comprise a radio
module and integrated flat panel
antenna.
• SU-E units: Include a radio
module and RF connector for a
separate external antenna.
Both types of outdoor units are
available with either 26dBm (HP-High Power) or 2dBm (LP-Low
Power) output power at the antenna port.
Subscriber units are available with single telephone line support
Unrestricted access unlimited choice.
BreezeACCESS II
BreezeACCESS II delivers a
comprehensive range of product
features, ensuring fast, consistent and
reliable data and voice service, including
Product Type Product Name Product Description
Miniature Indoor SU-ID-1D-2.4 Detached antenna - 1 data user
Subscriber Units SU-ID-BD-2.4 Detached antenna - full bridge
SU-R-1D-2.4 Detached antenna - 1 data user
SU-R-BD-2.4 Detached antenna - full bridge
Subscriber Units SU-A-1D-2.4 Integrated antenna - 1 data user
with an Outdoor SU-E-1D-2.4 Detached antenna - 1 data user
Radio Unit SU-A-BD-2.4 Integral antenna - full bridge
SU-E-BD-2.4 Detached antenna - full bridge
Product Type Product Name Product Description
Base Station Shelf BS-SH Base station chassis with
one DC power supply
BS-SH-AC Base station chassis with
one AC power supply
Outdoor Access AU-A-BS-2.4 Includes base station module and
Units for use outdoor unit with integrated antenna
with Base Station AU-E-BS-2.4 Includes base station module and
outdoor unit with connectors for
external antenna
Stand-alone AU-E-NI-2.4 Includes indoor unit and outdoor unit
Access Point with connectors for external antenna
Power Supply BS-PS Base station DC power supply
BS-PS-AC Base station AC power supply
GPS GU-A-BS Includes synchronization
Synchronization card and outdoor GPS radio
System unit with integrated antenna
SU-A-BD
SME/SOHO Residential
SU-A-1D1V

Radio
Frequency 2.4GHz ISM band
Radio Access Method FHSS CSMA/CA
Operation Mode Time Division Duplex
Standards ETSI ETS 300 328, FCC Part 15
Channel Bandwidth 1MHz
Output Power (at antenna port) SU-ID, AU-ID: 17dBm, 10dBm (ETSI)
SU-R: 26dBm (FCC)
SU-A/E, AU-A/E: 26dBm (HP) or 2dBm (LP), Control Range 20dB typical.
Antenna SU-A: 15dB, 20˚
AU-A: 16.5dBi, 60˚
Sensitivity Data Rate SU-ID, AU-ID SU-R SU-A/E, AU-A/E
(dBm at antenna port, BER 1E-6) 1 Mbps -81 -86 -87
2 Mbps -74 -80 -81
3 Mbps -66 -71 -73
Data Rate 3 Mbps max.
Modulation Multilevel GFSK
Outdoor Unit to Indoor Unit Communication
Intermediate Frequency (IF) 440MHz
IF Cable Impedance 50 ohm
Maximum IF cable Attenuation 15dB
Maximum IF cable DC Resistance 1.5 ohm
Voice Communication (DV series)
Protocol H.323 Voice over IP compliant
Compression G.723 6.3Kbps compression, G.729 8Kbps compression, G.711 64Kbps transparent
Echo Cancellation G.168, G.131
Configuration and Management
Local Management Via MON port, Monitor program using terminal emulation
Remote Management SNMP, Telnet, TFTP
Remote Management Access From the wired LAN or from the wireless link
SNMP agents MIB II, Bridge MIB, BreezeACCESS Private MIBs
Accounting Radius compatible client in subscriber units
Security Authentication, Filtering and Virtual LAN
Software upgrade TFTP download
Interfaces
RF (antenna) AU-ID, SU-ID: 2 x SMA jacks
AU-RE, SU-RE: N-Type jack, lightning protected
IF AU-RA/RE, SU-RA/RE outdoor units: TNC jack, lightning protected
SU-NI, AU-NI, BS-AU indoor units: TNC jack, lightning protected
Ethernet Indoor units: 10BaseT,(RJ 45) with 2 embedded LEDs
Telephone (DV series) RJ 11 (POTS)
Monitor Indoor units: 3-pin low profile
Power AU-RA/RE, SU-RA/RE outdoor units: 12VDC via the IF cable
SU-NI, AU-NI indoor units, SU-ID, AU-ID: DC power plug to the external power supply
BS-PS (Power Supply module of BS-SH): 4-pin DC power plug to a –48VDC power source
BS-PS-AC (Power Supply module of BS-SH-AC): 3-pin AC power plug to a 110/220VAC
power source
Electrical
SU-ID-xD (data only), AU-ID 5VDC / 1.5A from the external power supply
(supplied with the unit), 100-250 VAC, 47-63 Hz
SU-A/E, AU-A/E-NI, 12VDC / 2.5A from the external power supply
(supplied with the unit), 100-240 VAC, 47-63 Hz
BS-SH (modular base station shelf) -48VDC or 110/220 VAC, 200W for a fully equipped shelf.
25W each AU (outdoor unit plus indoor module)
Mechanical
SU-ID, AU-ID 13cm x 8.6cm x 3cm, 0.5 kg.
SU-RA 30cm x 30 cm x 7.2 cm, 3 kg.
AU-RE, SU-RE 30cm x 12 cm x 5 cm, 2.2 kg.
SU-NI, AU-NI 13cm x 8.6cm x 3cm, 0.5kg.
BS-SH 19”, 3U, depth 26cm, 6 kg. fully loaded
Environmental
Operating Temperature Indoor units and modules: 0˚C to 40˚C
Outdoor units: -40˚C to 60˚C
Operating Humidity 5% to 95% non-condensing. Outdoor units are weather protected.
Standards Compliance General
EMC EN 300-385, FCC Part 15
Safety EN 60950, UL 1950
Environmental ETS 300 019
811072 Rev.d
We're on your wavelength.
Affordable freedom
BreezeACCESS II is the ideal broadband wireless access system for
service providers operating in the unlicensed 2. GHz ISM band.
As a wireless alternative to wired access networks, BreezeACCESS II
leverages Frequency Hopping Spread Spectrum technology in Time
Division Duplex (TDD) mode to deliver reliable broadband data services,
reaching remote locations and bypassing unusable copper.
BreezeACCESS II provides an instant and independent infrastructure,
which is immediately deployable with lower infrastructure construction
and operating costs than any other solution on the market.
Specifications
BreezeACCESS™ II
We're on your wavelength.
www.alvarion.com
International Corporate
Headquarters
Tel: [phone]
Fax: [phone]
Email: [email protected]
North America Headquarters
Tel: [phone]
Fax: [phone]
Email: [email protected]
Latin America Caribbean
Tel: [phone]
Fax: [phone]
Email: [email protected]
Brazil
Tel: [phone]
Fax: [phone]
Email: [email protected]
China
Tel: [phone]
Fax: [phone]
Email: [email protected]
Czech Republic
Tel: [phone]
Fax: [phone]
Email: [email protected]
France
Tel: [phone]
Fax: [phone]
Email: [email protected]
Germany
Tel: [phone]
Fax: [phone]
Email: [email protected]
Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
Mexico
Tel: [phone]
Fax: [phone]
Email: [email protected]
Romania
Tel: [phone]
Fax: [phone]
Email: [email protected]
Russia
Tel: [phone]
Fax: [phone]
Email: [email protected]
U.K. Ireland
Tel: [phone]
Fax: [phone]
Email: [email protected]
Uruguay
Tel: [phone]
Fax: [phone]
Email: [email protected]
© Copyright 2004 Alvarion Ltd. All rights reserved.
Alvarion, BreezeCOM, WALKair, WALKnet, BreezeNET, BreezeMANAGE, BreezeACCESS, BreezeLINK, BreezePHONE, MGW, eMGW and/or
other products and/or services referenced here in are either registered trademarks, tradenames or service marks of Alvarion Ltd.
All other names are or may be the trademarks of their respective owners.
The content herein is subject to change without further notice.