Alvin MiniMaster MM36-3-WBR User manual

MiniMaster™Drawing Table
Tools required: Phillips screwdriver.
Assembly Instructions
Parts Included:
A 2pcs Leg Frame
B 1pc Table Top
F 2pcs
Front
Extension
Tubes
To Assemble:
Unpack and inspect contents to confirm that you have all parts
listed above.
Screw floor glides (G) or casters (H), whichever you prefer, into
bottom tubes of left and right leg frames (A).
Place back panel (C) on a bench or table (at least 20" high) with
ends hanging over the edge and threaded holes facing up.
Hang left leg frame (A) on top of back panel (C) as shown in
Figure 1. Align holes in steel flange with holes in back panel and
install ½" Allen bolts (K). Be sure ends of back panel are pushed
flush against steel tubing and tighten bolts securely.
Repeat step 4for right leg frame (A).
Carefully remove base assembly from table/bench and place
upright on floor. Use care not to overstress back panel connections
at this time.
Place shelf (D) with pre-drilled holes facing down onto the steel
shelf flanges. Attach with ½" Allen bolts (K) from below. Be sure
ends of shelf panel are pushed flush against steel tubing and
tighten bolts securely.
Insert front and rear extension tubes (Eand F) into base assembly.
Pay close attention to correct orientation of attachment brackets
on left and right rear tubes, as shown in Figure 2. Install height
adjustment knobs (J) in each leg and set each extension tube in
the third hole for the time being.
Extension tube holes align with height adjustment knobs when
half of the hole above is showing, as shown in Figure 3. Set base
assembly aside.
1
2
3
4
Colored surface both sides
C 1pc Back Panel
Colored surface one side only
D 1pc Shelf Left Right
Left Right
E 2pcs Rear
Extension
Tubes
G 4pcs
Floor Glides
H 4pcs
Casters M 1pc Pencil Ledge
J 4pcs
Height
Adjustment
Knobs
K 8pcs
½" Allen
Bolts
L 10pcs
5⁄8" Wood
Screws
5
6
7
8
Hint
Adjustment
Knob
Front
Extension
Tube Rear Extension Tube
½" Allen
Bolt
Figure 2
Floor Glides
½" Allen
Bolts
Figure 1
For MM36-3-WBR and
MM36-5 purchased after April 2008

©2008 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722
Phone: [phone] • Toll-Free: 800-444-2584 • Fax: [phone] • Toll-Free Fax: [phone] www.alvinco.com
LIT-A7424 1/08
Place table top (B) on carpeted or protected floor with pre-drilled
side up. Carefully turn table assembly upside down and place on
table top. Align holes in rear leg extension brackets (E) with pre-
drilled holes in table top. Connect using 5⁄8" wood screws (L) and
tighten firmly. Use care not to over tighten and strip.
Carefully return table assembly to the upright position.
Attach pencil ledge to front edge of table top using two screws (L)
as shown in Figure 5. Pencil ledge prevents materials from sliding
off of a tilted surface and the slotted connection allows for easy
adjustment from flush to elevated position.
9
10
11
12
Figure 3
Figure 4
5⁄8
"Screws
Flush Position Elevated Position
Figure 5
Table is now ready to use. Adjust table top to desired height
and angle using the height adjustment knobs and enjoy!
Send us your
comments and
suggestions and
we’ll send you
free Drafting Dots!
Alvin Drafting Dots (#DM123) work well to tape
your paper and other media to the tilted table
surface. To receive a free roll of Drafting Dots,
simply visit the “Contact Us” page on our website
www.alvinco.com and submit your comments
and suggestions about our MiniMaster table. We
are constantly working on product improvements
and look forward to hearing from you.
Extension tube holes
align with height
adjustment knobs
when half of the hole
above is showing.
Hint
5⁄8
"Screws Pencil Ledge