Amaircare ET Annual Filter User manual

Amaircare® ET Annual Filter Kit Super Standard Installation Instructions for Models 2500 and 3000 (2016) NA
ANNUAL FILTER
KIT - SUPER STANDARD
Installing ET Style replacement filters in Models 2500
and 3000
Open the cabinet
1. Turn the unit o and unplug it.
2. Unscrew the 4 lid screws with a No. 2 Phillips screw driver. Once all
screws are out, remove the metal lid.
3. Bracing the unit so it does not move, gently press down on the
HEPA Cartridge and turn counterclockwise until it unlocks, then li
the HEPA Cartridge out of the Air Filtration System.
Carbon Prefilter
1. Remove the aluminum clips from the used carbon prefilter,
unwrap it from the HEPA Cartridge and discard.
2. Remove plastic packaging from the new Carbon Prefilter.
3. Wrap the new Carbon Prefilter around the HEPA Cartridge and
secure in place with the aluminum clips.
4. Slide the HEPA Cartridge with new Carbon Prefilter back in the
center of the unit.
5. Gently press down on the HEPA Cartridge and turn clockwise until
it locks into place.
Carbon Inner Blanket
1. Remove the used Carbon Inner Blanket by curling one end of the
filter to the inside. Carefully slide the blanket out from the center
of the HEPA Cartridge.
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
1
2
34
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER

Amaircare® ET Annual Filter Kit Super Standard Installation Instructions for Models 2500 and 3000 (2016) NA
2. Remove the plastic packaging from the new Inner Carbon
Blanket.
3. In the opposite direction to which it was rolled in the package,
roll the new Carbon Inner Blanket into a cylinder.
4. Slide the rolled filter into the center of the HEPA Cartridge and
lightly press the Carbon Inner Blanket into place against the
inside of the HEPA Cartridge.
5. Remove the old O-Ring/Gasket from the Venturi inside the unit.
Replace with the new O-Ring provided in the Annual Kit.
6. Slide the HEPA Cartridge with new Carbon Inner Blanket back in
the center of the unit.
7. Gently press down on the HEPA Cartridge and turn clockwise
until it locks into place.
Close the cabinet
1. Position the hexagonal lid on the unit with the centered hole at
the rear of the unit.
2. To replace the lid screws, press down firmly on the lid to align
the holes and then insert and fasten screws.
3. Plug the unit in and turn it on.
4. To set the Filter Monitors, press and hold the corresponding
buttons on the control pad until the blue LEDs illuminate.
Need help? Call us!
1-800-268-7732
www.amaircare.com Made in Canada
Americair Corporation 770 Gana Court, Mississauga, Ontario, Canada
Amaircare is a registered trade mark of Americair Corporation in the
United States and Canada.
PREFILTER
HEPAFILTER
VOC BLANKET
VOC CANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER
PREFILTER
HEPAFILTER
VOCBLANKET
VOCCANISTER