Amana ARR6400 Series Manual

Amana Technical Information Electric Range
ARR6400 P1142670N, Pi143415N, P1143432N, P1143457N, P1143607N, P1143640N,
P1143653N, P1143674N
ART6510 P1143460N, P1143469N, P1143482N, P1143611N, P1143630N, P1143657N
•Due to possibilityof personal injuryor property damage, always contact an authorized technician for servicingor
repair of this unit.
•This technical sheet replaces RT2320003 Rev. 8.
•Refer to Service Manual RS2320004 for detailed installation, operating, testing, troubleshooting, and disassembly
instructions.
• Refer to Parts Manual RP2320040 for part number information.
CAUTION
MI safety information must be followed as provided in Service Manual RS2320004. I!
[WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
II
Models I ARR6400 IART6510
I Power Source
Electrical rating 240/208 V 240V
13.8 kW/10.4 kW 12,9 kW
50 Amp max. 50 Amp max.
60Hz 60Hz
Amperage
Frequency
Element Wattage @ 240/208 v
6 inch ribbon radiant
7 inch ribbon radiant
8 inch ribbon radiant
9 inch ribbon radiant
Two 6 inch coils
Two 8 inch coils
Oven Wattage @ 240/208 V
Bake
Broil
Oven Interior ,Dimensions In. (cm)
Height
Width
Depth
Product Exterior Dimensions In. (cm)
Height overall
Width
Depth oven door dosed with handle "
Clearance oven door
Height of cooktop
Weight Ibs. (kg)
Approximately shipping wel'ght
Cook'top Surface -Upswept
Recessed porcelain
Lilt-up cooktop with support rods
Interior oven light
La_e window frameless glass door
Removable fullwidth storage drawer
Two oven racks 5 - positions
Porcelain burner bowie
Porcelain coated baek_luard
Glass back_luard
S_llsaver TM cooktop
Touchmatic ERC
1,500/*
2,600/*
1,200
tr500
2_000
2,500
2t500/* 2r500
3000/* 3r000
16 (41} 16 (41)
2"3(58) 23 (58)
t7 1/2 (45) 17 1/2 (45)
47(119) 47(110)
s0_76) 30(76)
20 1/4{72) 28 1/4('/2)
22(56) 22(56)
36(91) 36(91)
171 (78) 171 _78)
X
X
x
X
x
X
X
X
X
X
X
X
X
X"
X
X
"- Rating of 208 VAC is approximately 80% of 240 VAC value.
April 1999 1 RT2320003 Rev. 9

Component Testing Procedures
f WARNING
testing requires it.
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
nlustration
31823701
31722801
301491
Component
Oven light socket
Oven indicator light
and
Surface indicatorlight
Rocker switch
Test Procedure
Test continuityof receptacle
terminals.
Remove one lead fromswitch
terminal and measure resistance
acrossterminals.
Measure voltage at indicatorlight.
Measure continuityofswitch
positions:
Closed
Open
Test continuityofterminals.
Results
Indicates continuitywith bulbscrewed in.
If notreplace.
Switchclosed: 0
Switchopen: Infinite resistance
]f voltage is present and lightdoes not
operate. Replace light.
If no voltage is present at indicatorlight
checkwidng.
Continuity, if not replace.
Intinife,if not replace.
Continuity, if notreplace.31734602--1500 W Coil surface elements
31734606--2600 W6" and 8"
31730101 Coil surface terminal Remove element and turn surface
block element on and test for voltage at 240 VAC
terminal block.
31794701-1200 W Ribbon radiant Remove one wire lead from element Continuity,if not replace.
31794601-1500 Welements and measure resistanceof the 1200W: 45 to 51
31794501-2000 W element, t50OW: 36 to 41
31794801-2500 W 200OW: 27 to 31
2500W: 21 to 25
Ribbon surface
thermal limiter/hot
lightswitch
I Bake element
Broil element
31846201
059552
Tum surface element on and test for
voltage. See wiringdiagram and
schematic.
la-2a 240 VAC
lb-2b 120 VAC
Disconnect leads and measure
resistanceon the following:
la-2a roomtemperature-continuity
lb-2b room temperature-infinite
Disconnectwire leads toelement and
measure resistance ofterminals.
Measure voltage at bake element.
Disconnectwire leads toelement and
measure resistance ofterminals.
Measure voltage at broilelement.
Measure resistance.
Remove wiringfromterminals H1 and
H2. Connect Volt ohms meter to
H1 and H2.
Measure the followingfor voltages at
LO, MED, HI:
H1 to H2
061732
314907
31891202
Oven temperature
sensor
Infinite switch
240 VAC
Etectmv_
Continuity,approximately 23 Q,
ifnot replace.
240 VAC, see wiringdiagram forterminal
identification.
Ifno voltage is presentat bake element
check widng.
Continuity, approximately 19 £_,
if notreplace.
240 VAC, see wiring diagram for terminal
identification.
If novoltage is present at broilelement
checkwidng.
Approximately1100 _at room
temperature 75°F.
Time On Time Off
LO 5% 95%
MED (4-5) 50% 50%
HI 100% 0%
240 VAC, if not replace switch.
'1
RT2320003 Rev. 9 2 Apd11999

Component Testing Information
I I WARNING
To avoid risk of electrical shock, personal injury, or death, diSconnect power to oven before servicing, unless
testing requires iL
I
Illustration
053584
31715201--LH
31715202--RH
065780
305797
31797301
Component Test Procedure Results
Control limit Normally Closed
Verify proper operation.
Closed 245°F Continuity
Open 275°F Infinite
If open at roomtemperature, replace.
Hinge
Door lock switch
Door plunger switch
Autotatch assembly
withdoor plunger
switch
Carefully open the hinge fully,and
insert a wooden dowelor screwdriver
bitintoopening.
Remove top and bottom screws
:securing hinge.
Slide hinge top towards rear ofunit
and guide hinge outthrough frame
opening or storage drawer.
Switch connectionin following
positions:
Unlooked
Looked
;et ERC to Clean
Remove switchfrom unitand measure
the following points:
C-NC
CNO
Disconnect wires and test for
continuityper diagram
I4_ CAUTION II
Do not placehands in hinge area when I
Ovendooris removed. Hinge can snap
closed and pinch hands or fingers.
COM-NO=Open, COM-NC=Closed
COM-NO=Clceed, COM-NC--Open
Lock LED should flash
LookLED and Oven LED should
illuminate,If LockLED doesnot
illuminate,check switch and widng.
Plunger ininfinite,Plunger out continuity.
Plunger incontinuity,Plunger out infinite.
NC NC
__, ,_
,:....a_H.__.....___.o_ _.. ;
April 1999 3 RT2320003 Rev 9

Component Testing Procedures
I L WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it. '1
IllustraUon Component
ERC3 -Touchmatic
electronic range
control
Test Procedure
F1---Shorted pad button.
F2---Oven cavityover temperature.
F3---Open circuitinoven temperature
sensor circuit.
F4_Shorted circuitin oven
temperature circuit.
F5--Defective watchdog circuitin
contmL
F"/-_Failure ofdoor lockswitchsensing
with door looked.
Fg--Failure of door lockswitching
sensingwith door unlocked.
DOOR--Look statusis notsensed
within 20 seconds ofenergizing door
lookrelay.
Push BAKE pad.
Push SLEWpad untilan oven
temperature greaterthan 500°F
displays.
IImmediately pushand hold BAKEpad
until"00" displays,approximately 5
seconds.
To decrease oventeroperatara (for a
cooler oven), Push SLEWpad until
negative numbersappear, Oven can be
adjustedfrom -05 ° to -35°ower. To
avoid over adjustingoven move
temperature -5°each time.
To increase oven temperature (for a
warmer oven), PushSLEWped until
positive numbersappear. Oven can be
adjusted from 5" to 35° higher.To avoid
over adjustingoven move temperature
5° each time.
Push OVEN CANCEL button.
Temperature adjustmentwillbe
retained even through a powerfailure.
Controlwillautomaticallycancel any
cookingoperationand remove all relay
ddves 12 hoursafter the last pad touch.
Controlinputfeatures willbe disabled
and displaywill indicate"OFF", when
BAKE and CLOCK are pushed
simultaneouslyand heldfor 5 seconds.
Controlwill returntonormal operat on
by repeatingthe procedure.
Bake
Broil
ERC3 Controlled
ERC3 Controlled
ERC3 Controlled
ERC3 Controlled
Oven temperature
adjustment
Twelve hour off
Child lock out
Drive requirements
Based on a 60
second cycle.
Clean
Stage 1
Stage 2
Lock light
Results
Verify actuatoroperation.
Check sensorwidng, sensor, and
temperature limiter,
Check sensor resistanceand wiring.
Check sensor resistanceand widng.
Replace ERC3.
Check latchswitchand door motor.
Check latch switchand door motor.
Vedfy operationof door latchswitches.
While increasingor decreasing oven
temperature, this does notaffect self-
cleaningtemperature.
100% bake 10°1,broil
0O,_,bake 100% broil HI
0% bake 93% broil 5
0% bake 87% broil 4
0% bake 80% broil 3
0% bake 73% bmil 2
0% bake 57"/,,broil 1
Time controlled15 minutes 0% bake
100% broil.
Time controlled100% bake 10o/obroil.
On at the startof the clean cycle.
Off at approximately 400°F + 25°F.
RT2320003 Rev. 9 4Apd11999

Wiring Diagram and Schematic
[ WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
I
I[NPERATURE CO. 9BIN 9SOCKET
SENSOR PLUG CAP
Lr SI IlK
B PIN I_C
ILOCK
u J\ $ I L
WB BU \ " II
RU 2SOCKET
CIR OR
_L
BOON
lATCH $I
VT VT
5TERNCONNECTOR
RELAY CONNECTIONS
(BR) (LI) (BA)
ELECTRONICRANGE
CONTROL(E.R,C.)
J4- IOIERN CONNECTOR
OVENHIGHLIMIT
NO
YL 2SOONBAKE
16
CA
UOO0t
BROtL
COLOR COLOR '
REO KO ROUGE
OR
SURFAC[ ELEg [BES
R.F. R,R.
CA
K2
SWITCH
R.R.
12 LI
SUHUACEELEKENTS
L,R. L.F.
18 IB 16 I
CA CA Ok C
BU YL
(,,TG,K'
L_F_
! El P
_6CA RD _
16CA BK
MAINTOP
IOH1 A
IFACE Vl
EOR H
_H CBASS]SCNO
LE'T
SURFACE
BACKCUARO IUOA NEON
10 HASSIS
_GROUNO
BE
ORANC_O_
YElLO_ Y L JAUN_
GREE_ O_ VEBI
BLUE eu BLEU_U
WOL_) V T v_OlEl
BLACK BK NOIR
Re0H_ e_
NOTES:
CLEFL [NO $ RICHI ENO $FLUOR,
FLUOR. FLUOR. LIGHT
LIC HE LlOHT SW IICH
UALLASE
BU_WH
IALLINT[RNALN(RESAR_ 1BGA,)SB "C XLUNLESSOIBER()S[ NOTEO
2ALLREPLAC[MENFIVIB[S MUSE HAVE SANE BALING AS
OBIG IKAI W liE[S,
_S[[ S[BIAIPLAI[ FORINPUIVOLFAC[_AIIAO[ RATING,
40_NOT[BOPIlONAIEOUIPMEKIANDBELAI[OIVIRING ROE
SUPPII[O ON SOME MOO[IS
5,[LEN[NT WAFIAC[SVARY BYIIOOEL. REPLKCENENIELEMENTS
NUSI HAVE sag[ NKEIAG[ AS ORIGINALELEKENIS.
U.FOR RANGL INSTALLAIION,USECOPPER glUE ONLY.
).GROUNDSIRAPN01 US[G BOB FOUR VIIR[ INSIALLAEIOKS,
]
(,,,.r_,, L,.', -ELECIRICALSHOCKHAZARO
I/_x wAKI_III_b DISCONNECTPOWERAIMAIN
i/LJ\ FUSE ORC_RCUII BREAKER BEFORE SERVICING
J/-JI_FAILURE TO DO SO COULD RESULI INSERIOUS
INJURY OR DEATH
-RSOUE DE CHOC ELECIRQUE
DANGER _)EBRANCHERL'ALIMENIATIONELECTRIQUE.
AVANT DI"NIRETENIR CETTE UNITE.
LEIRANQUE DE RESPECI DECETTE CONSIGNE POURRAIT
AVOIRCOI,II_ERESULTAT UNF BLESSURE GRAVE OU uORIELLE
ARFI6400
April 1999 5 RT2320003 Rev. 9

Wiring Diagram and Schematic
I_lb WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
SUR[AC[
RED
ELI) _E_ {SUREAOENEOR
(NOIE _)
II
2600W
_TJan
RF I
L_ IL2 I
_OVEN
LIGHT
SWITCH
WH J440
J4_
!500W
KK I
tl IL2 I
2600R
E
L_
1500W
FLUOR.
LIGHTS¥ _ TLUOR.LIGHT _ BALLAST
E_] YL (SURFACE) =
,'0 T;o
$STARTER OVEN
:_ LIGHT
40W
BOOR
SWITCH _e
oJ2
CIRCUIT
WHEN LINE
BREAKNOI USED
BLACK
(L2)
WHITE
(N)
;REEN
Or
BARE
CHASS{S
GRBUNO
(FOUR W IRE
INSTALLATIONS
ONLY)
DRI
_GROUND
SERAR
DOOR LOCK
wHMOTOR GROUND STRAP
NOT USEDFOR
RD FOUR"NIRE
tNSTALLATtORS
J2-S
Vl BOOR LATCH
SWITCH
J2,4
G_I RANGE
CONDIIIONS
SHOWN:
"J2-5
{LEUENTSOTF
_)OOR UNLA[CHEB
AND CLOSEO
SCHEMATIC
35-51890601 49
ARR6400
RT2320003 Rev. 9 6 Apd11999

Wiring Diagram and Schematic
[WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
RD
[[_PE_T_E PIN g SOCKET st2 _2
_I60R DOOR CAP
SW BK OR SF? VT SF2
T
I4GA GN
OULEUR
JAUNE
BLEU
NOIR
BLAN_ ,
NOTES :
ALL INTERNAL W[RES ARE IBGA, 150"rC XL UNL[$S
O/HERWISE NOTED• SF2 IS SEW-2/SF2 2OO'rC.
2. ALL REPLACEktENT WIRES MUST HAVE SAME RATING AS
)LIGHT
3R_(OVEN
(N)wH I
BK 14GA t_ !
(N
x
OR]G[NAL WIRES. MAIN /
3. SEE SERIAL PLAIE FOR INPUT VOUAGE/_/ATTACE RA]ING. TERMINAL I
• _OR (--)DENOTES OPTIONAL EQUIPMENT AND RELATED WIRING NOT BLOCK
SUPPLIED ON SOME MODELS.
5_LEMENT WATTAGES VARY BY MODEL REPLACEMENT ELEMENTS
MUST HAVE SAME WATIAGE AS ORIGINAL ELEMENTS. _ POWER CO
6FOR RANO_ ]NSIALLAT]ON, USE COPPER WIRE ONLY" _nIAGRAFA
7GROUND STRAP NO1 USED FOR FOUR WIRE INSTALLATIONS
RO
(NOIE 7)
GROUND
STRAP
F--j_
/
CHASSIS
GND
WARN I NC -ELECTRICAL SHOCK HAZARO - RISQUE DE CHOC EL_CTRIQUE
DISCONNECT POWER AT MAIN DAN_ER- DEBRANCHER L'AL[MZNTATION ELECTRIQUE_
AVANT D'ENIRETENIR CETTE UNITE.
FUSE OR CIRCUIT BREAKER BEFORE SERVICING.
FAILURE TO DO SO COULD RESULT IN SERIOUS LE MANQUE DE RESPECT DE CETIE CONSIGNE P0URRAIF
INJURY OR DEATH AVOIR COMME RESULTAT UNE BLESSURE GRAVE 0U MORTELLE.
ART6510
April 1999 7 RT2320003 Rev. 9

Wiring Diagram and Schematic
I _k WARNING II
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless
testing requires it.
RED
(L1) (SEE NOTE 5)
RD
SURf
NEON (
RF
2500W
"LFLF
R
LI
LR
2OOOW
H1 q
LF
120_
PLI[L2
FLUOR. LIGHT
(SURFACE)
STARTER
_OVEN
LIGHT 40W
DOOR
SWITCH
WH
RESISTER
_cuI1 WHEN tlNE
BR[AKNOT USED
LOCK _GROUND
STRAP :
GROUND STRAP
SENSOR ROT USED FOR
FOUR WIRE
INSTALLATIONS
X_
EN
J2-3 BARE
DOOR LATCH
SWITCH CHASSIS
GROUNO
(FOUR WIRE
INSIALLAT IONS
ONLY)
RANGE
CONDITIONS
SHOWN:
-ELEMENTS OF,:" AND AT
ROOM TEMPERATURE
-DOOR UNLATCHED
AND CLOSED
SCHEMA1- I C
ART6510
RT2320003 Rev, 9 8 Apn11999