Amazone KG 4001-2 User manual

Operating manual
az
Soil tillage implement
Rotary cultivator
KG 4001-2
KG 5001-2
KG 6001-2
MG4372
BAH0060-5 12.17
Please read and follow this
operating manual before putting
the machine into operation.
Keep it in a safe place
for future use!
en

2 KG 4/5/6001-2 BAH0060-5 12.17
READING THE INSTRUCTION
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success one should go into
the mind of a thing or make himself familiar with
every part of the machine and to get acquainte
d
with its handling. Only this way, you would be
satisfied both with the machine as also with
yourself. To achieve this is the purpose of this
instruction manual.
Leipzig-Plagwitz 1872.

Identification data
KG 4/5/6001-2 BAH0060-5 12.17 3
Identification data
Please insert the identification data of the implement. The
identification data are arranged on the rating plate.
Implement ID No.:
(10-digit)
Type: KG 4/5/6001-2
Permissible system pressure (bar): Maximum 210 bar
Year of manufacture:
Basic weight (kg):
Permissible total weight (kg):
Maximum load (kg):
Manufacturer's address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 501-0
+ 49 (0) 5405 501-234
[email protected]
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number: MG4372
Compilation date: 12.17
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2014
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.

Foreword
4 KG 4/5/6001-2 BAH0060-5 12.17
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product
range of AMAZONEN-WERKE, H. DREYER GmbH & Co. KG. We
thank you for your trust in our products
On receiving the implement, check to see if it has been damaged
during transport or if parts are missing. Using the delivery note, check
that the implement has been delivered in full, including any special
equipment ordered. Damage can only be rectified if problems are
signalled immediately.
Before initial operation, read and observe this operating manual, and
particularly the safety information. Only after careful reading will you
be able to benefit from the full scope of your newly purchased
implement.
Please ensure that all the implement operators have read this
operating manual before they put the implement into operation.
Should you have any questions or problems, please consult this
operating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your implement.
User evaluation
Dear Reader
We update our operating manuals regularly. Your suggestions for
improvement help us to create ever more user-friendly operating
manuals. Send us your suggestions by fax.
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 501-0
+ 49 (0) 5405 501-234
[email protected]

Table of Contents
KG 4/5/6001-2 BAH0060-5 12.17 5
1User information..........................................................................................8
1.1Purpose of the document.........................................................................................................8
1.2Locations in the operating manual...........................................................................................8
1.3Diagrams..................................................................................................................................8
2General safety instructions.........................................................................9
2.1Obligations and liability ............................................................................................................9
2.2Representation of safety symbols..........................................................................................11
2.3Organisational measures .......................................................................................................12
2.4Safety and protective equipment ...........................................................................................12
2.5Informal safety measures.......................................................................................................12
2.6User training...........................................................................................................................13
2.7Safety measures in normal operation ....................................................................................14
2.8Danger from residual energy .................................................................................................14
2.9Maintenance and repair work, fault elimination .....................................................................14
2.10Design changes .....................................................................................................................15
2.10.1Spare and wear parts and aids..............................................................................................16
2.11Cleaning and disposal............................................................................................................16
2.12User workstation ....................................................................................................................16
2.13Warning symbols and other labels on the implement............................................................17
2.13.1Positions of warning symbols and other labels......................................................................24
2.14Dangers in case of non-observance of the safety instructions ..............................................25
2.15Safety-conscious working ......................................................................................................25
2.16Safety information for users...................................................................................................26
2.16.1General safety instructions and accident prevention instructions..........................................26
2.16.2Mounted implements..............................................................................................................30
2.16.3Hydraulic system....................................................................................................................31
2.16.4Electrical system ....................................................................................................................32
2.16.5PTO shaft operation...............................................................................................................32
2.16.6Cleaning, maintenance and repair.........................................................................................34
3Loading and unloading .............................................................................35
4Product description...................................................................................36
4.1Overview of assembly groups................................................................................................36
4.2Safety and protective equipment ...........................................................................................38
4.3Overview – Supply lines between the tractor and the implement..........................................39
4.4Transportation equipment ......................................................................................................40
4.5Proper use..............................................................................................................................41
4.6Danger areas and danger points ...........................................................................................42
4.7Rating plate and CE mark......................................................................................................43
4.8Noise production data ............................................................................................................43
4.9Technical data........................................................................................................................44
4.9.1Data for the calculation of tractor weights and tractor axle loads ..........................................44
4.10Necessary tractor equipment .................................................................................................45
4.11Gearbox – Transmission fluids and filling quantities .............................................................46
4.12Spur gear trough – oils and filling quantities..........................................................................47
5Layout and function...................................................................................48
5.1Threaded cartridge.................................................................................................................49
5.2Attachment category ..............................................................................................................50
5.2.1Coupling elements, tractor mount Cat. 3 ...............................................................................50
5.2.2Coupling elements, attachment category Cat. 4N .................................................................50
5.2.3Adapter frame Cat. 5 (optional)..............................................................................................51
5.3Three-point extension frame (optional)..................................................................................52

Table of Contents
6 KG 4/5/6001-2 BAH0060-5 12.17
5.4Tractor wheel mark eradicator (optional) .............................................................................. 53
5.5Rollers ................................................................................................................................... 54
5.5.1Cage roller SW ...................................................................................................................... 54
5.5.2Tooth packer roller PW ......................................................................................................... 55
5.5.3Wedge ring roller KW ............................................................................................................ 55
5.5.4CDW cracker disc roller ........................................................................................................ 55
5.6Drive ...................................................................................................................................... 56
5.6.1Gearbox/tractor PTO shaft speed/tine speed ....................................................................... 57
5.7Two-gear gearbox ................................................................................................................. 57
5.8Oil cooler (optional) ............................................................................................................... 58
5.9Universal joint shafts ............................................................................................................. 58
5.10Electronic drive monitor (optional)......................................................................................... 59
5.11Tool tines............................................................................................................................... 61
5.11.1Tool tine minimum length ...................................................................................................... 62
5.11.2Stone release ........................................................................................................................ 62
5.12Working depth of the soil tillage implement .......................................................................... 63
5.12.1Mechanical adjustment of the working depth........................................................................ 63
5.12.2Hydraulic adjustment of the working depth (optional) ........................................................... 63
5.13Side panel ............................................................................................................................. 64
5.13.1Soil guiding angle bracket (optional)..................................................................................... 64
5.14Levelling board ...................................................................................................................... 64
5.15Centre line eradicator (optional)............................................................................................ 65
5.16Track markers (optional) ....................................................................................................... 65
5.17Combination possibilities with other implements .................................................................. 66
6Initial commissioning................................................................................ 67
6.1Checking the suitability of the tractor .................................................................................... 68
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and load
capacities, as well as the minimum ballast ........................................................................... 69
6.2Securing the tractor/implement against unintentional start-up and rolling ............................ 73
6.3Attachment of the wheel mark eradicators............................................................................ 74
6.4Attaching the rollers (specialist workshop)............................................................................ 74
6.4.1Adjusting the length of the universal joint shaft to the tractor (specialist workshop) ............ 76
6.5Hydraulic hose lines .............................................................................................................. 77
6.5.1Coupling the hydraulic hose lines ......................................................................................... 77
6.5.2Uncoupling the hydraulic hose lines...................................................................................... 78
7Coupling and uncoupling the implement................................................ 79
7.1Coupling the implement to the tractor ................................................................................... 81
7.2Uncoupling the implement..................................................................................................... 85
8Settings...................................................................................................... 87
8.1Adjusting the working depth of the rotary cultivator .............................................................. 88
8.1.1Mechanical adjustment of the trailing roller........................................................................... 88
8.1.2Hydraulic adjustment of the trailing roller .............................................................................. 90
8.1.3Adjustment of the leading tyre packer................................................................................... 90
8.2Adjusting the side panels ...................................................................................................... 92
8.3Adjusting the tractor wheel mark eradicator.......................................................................... 93
8.4Adjusting the levelling board ................................................................................................. 94
8.5Adjusting the track marker .................................................................................................... 95
8.6Setting the speed of the tool tines......................................................................................... 96
8.6.1Gear lever adjustment........................................................................................................... 96
8.7Adjusting the cutting rail (optional, only with cracker disc roller) .......................................... 97
8.7.1Adjusting the spring force...................................................................................................... 97
8.7.2Readjusting worn blades....................................................................................................... 98
8.7.3Adjusting the response.......................................................................................................... 98
8.8Adjusting the roller scraper ................................................................................................... 99

Table of Contents
KG 4/5/6001-2 BAH0060-5 12.17 7
8.8.1Wedge ring roller....................................................................................................................99
8.8.2Tooth packer roller .................................................................................................................99
9Transportation .........................................................................................100
10Use of the implement...............................................................................103
10.1Unfolding/folding the implement booms...............................................................................105
10.1.1Unfolding the implement booms ..........................................................................................106
10.1.2Folding the implement booms..............................................................................................106
10.2Folding in the lighting system...............................................................................................108
10.3On the field...........................................................................................................................109
10.3.1Work commencement ..........................................................................................................109
10.3.2During the work....................................................................................................................109
10.3.3After use...............................................................................................................................111
11Faults........................................................................................................113
11.1Initial use of the tooth packer roller......................................................................................113
11.2Hall sensor on the gearbox..................................................................................................113
11.3Tool tines stopping when work is in progress ......................................................................114
12Cleaning, maintenance and repair..........................................................115
12.1Safety first ............................................................................................................................115
12.2Cleaning the implement .......................................................................................................116
12.3Adjustment work ..................................................................................................................117
12.3.1Switching the gear wheels in the two-gear gearbox (specialist workshop) .........................117
12.3.2Replacing the tool tines (specialist workshop).....................................................................118
12.4Lubrication specifications.....................................................................................................119
12.4.1Lubricants.............................................................................................................................119
12.4.2Greasing points – overview..................................................................................................120
12.5Maintenance schedule – overview.......................................................................................121
12.6Two-gear gearbox................................................................................................................123
12.7Angular gearbox...................................................................................................................124
12.8Spur gear trough ..................................................................................................................125
12.8.1Changing the oil filter in the cooling kit (specialist workshop) .............................................126
12.9Checking the upper and lower link pins ...............................................................................126
12.10Checking/cleaning/lubricating the ratchet clutch (specialist workshop)...............................127
12.10.1Installation instructions for the ratchet clutch.......................................................................127
12.11Hydraulic system..................................................................................................................128
12.11.1Labelling of hydraulic hose lines..........................................................................................129
12.11.2Maintenance intervals ..........................................................................................................129
12.11.3Inspection criteria for hydraulic hose lines...........................................................................129
12.11.4Installation and removal of hydraulic hose lines ..................................................................130
12.12Adjusting the speed of the implement booms during folding (specialist workshop) ............131
12.13Screw tightening torques .....................................................................................................132

User information
8 KG 4/5/6001-2 BAH0060-5 12.17
1 User information
The User Information section provides information on use of the
operating manual.
1.1 Purpose of the document
This operating manual
describes the operation and maintenance of the implement.
provides important information on safe and efficient handling of
the implement.
is a component part of the implement and should always be kept
with the implement or the towing vehicle.
must be kept in a safe place for future use.
1.2 Locations in the operating manual
A
ll the directions specified in the operating manual are always seen in
the direction of travel.
1.3 Diagrams
Instructions and responses
Activities to be carried out by the user are given as numbered
instructions. Always keep to the order of the instructions. The reaction
to the handling instructions is given by an arrow.
Example:
1. Instruction 1
→Implement response to instruction 1
2. Instruction 2
Lists
Lists without an essential order are shown as a list with bullets.
Example:
Point 1
Point 2
Item numbers in diagrams
Numbers in round brackets refer to the item numbers in the diagrams.
The first number refers to the diagram and the second number to the
item.
Example: (Fig. 3/6)
Figure 3
Item 6

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 9
2 General safety instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations.
have been trained in working with/on the implement.
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state.
to replace damaged warning symbols.
If you still have queries, please contact the manufacturer.
Obligations of the user
Before starting work, anyone charged with working with/on the
implement is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations.
to read and understand the "General safety information" section
of this operating manual.
to read the "Warning pictograms and other labelling on the
implement" section of this operating manual and to follow the
safety instructions of the warning pictograms when operating the
implement.
to get to know the implement.
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not possess the appropriate technical knowledge,
then they should report this fault to their superior (operator).

General safety instructions
10 KG 4/5/6001-2 BAH0060-5 12.17
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions to
the health and safety of the user or third parties,
the implement,
other property.
Only use the implement
for the purpose for which it was intended.
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement.
Improper installation, commissioning, operation and
maintenance of the implement.
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety equipment.
Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance.
Unauthorised design changes to the implement.
Insufficient monitoring of implement parts which are subject to
wear.
Improperly executed repairs.
Disasters due to the effects of foreign objects and force majeure.

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 11
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates a direct threat at high risk which will result in death or
most serious bodily harm (loss of limbs or long-term harm),
should it not be prevented.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity
required for proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.

General safety instructions
12 KG 4/5/6001-2 BAH0060-5 12.17
2.3 Organisational measures
The operator must provide the necessary personal protective
equipment as per the information provided by the manufacturer of the
crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operating manual
must always be kept at the place at which the implement is
operated.
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and
protection equipment must be properly attached and fully functional.
Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 13
2.6 User training
Only those people who have been trained and instructed may work
with/on the implement. The operator must clearly specify the
responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the
supervision of an experienced person.
Person
Activity
Person
specially trained
for the activity 1)
Trained
person 2)
Person with specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Initial commissioning X 
Set-up, tool installation X
Operation X 
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X

Legend: X..permitted ..not permitted
1)
A person who can assume a specific task and who can carry out
this task for an appropriately qualified company.
2) Instructed persons are those who have been instructed in their
assigned tasks and in the possible risks in the case of improper
behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and
measures.
3) People with specialist technical training shall be considered as a
specialist. Due to their specialist training and their knowledge of
the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained
from several years' experience in the relevant field.
If maintenance and repair work on the implement is additionally
marked "Workshop work", only a specialist workshop may carry out
such work. The personnel of a specialist workshop shall possess the
appropriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
implement in a way which is both appropriate and safe.

General safety instructions
14 KG 4/5/6001-2 BAH0060-5 12.17
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operating personnel. You can
find detailed information in the relevant sections of this operating
manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assemblies to lifting gear when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety devices.

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 15
2.10 Design changes
You may make no changes, expansions or modifications to the
implement without the authorisation of AMAZONEN-WERKE. This
also applies when welding support parts.
Any expansion or modification work shall require the written approval
of AMAZONEN-WERKE. Only use modification and accessory parts
approved by AMAZONEN-WERKE so that the type approval, for
example, remains valid in accordance with national and international
regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear.
increase the size of existing holes on the frame or the running gear.
weld support parts.

General safety instructions
16 KG 4/5/6001-2 BAH0060-5 12.17
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or the parts
cleared by AMAZONEN-WERKE so that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of non-approved spare and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment
and
when cleaning using solvents.
2.12 User workstation
The implement must be operated by only one person from the driver's
seat of the tractor.

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 17
2.13 Warning symbols and other labels on the implement
Always keep all the warning symbols of the implement clean and in a
legible state. Replace illegible warning symbols. You can obtain the
warning symbols from your dealer using the order number
(e.g. MD 075).
Warning symbols – structure
Warning symbols indicate danger areas on the implement and warn
against residual dangers. At these points, there are permanent or
unexpected dangers.
A warning symbol consists of two fields:
Field 1
is a symbol describing the danger, surrounded by triangular safety
symbol.
Field 2
is a symbol showing how to avoid the danger.
Warning symbols – explanation
The column Order number and explanation provides an explanation
of the neighbouring warning symbol. The description of the warning
symbols is always the same and specifies, in the following order:
1. A description of the danger.
For example: risk of cutting
2. The consequence of non-compliance with the risk avoidance
instructions.
For example: causes serious injuries to fingers or hands.
3. Risk avoidance instructions.
For example: only touch implement parts when they have come
to a complete standstill.

General safety instructions
18 KG 4/5/6001-2 BAH0060-5 12.17
Order number and explanation Warning symbols
MD 075
Risk of cutting or severing of fingers/hand
through direct contact with moving parts
involved in the working process!
This hazard can cause the most severe injuries
with loss of body parts.
Never reach into the danger area when the
tractor engine is running with the universal
joint shaft or hydraulic/electrical system
connected.
Wait until all moving parts of the implement
are at a standstill before reaching into the
danger area.
MD 076
Risk of drawing-in/entrapment for hand or
arm due to moving force-transmission parts!
This hazard can cause the most severe injuries
with loss of body parts.
Never open or remove protective equipment,
while the tractor engine is running with the
universal joint shaft or hydraulic/electronic
system connected.
if the ground wheel drive is moving.
MD 078
Risk of crushing of fingers/hand by
accessible, moving parts of the implement!
This hazard can cause the most severe injuries
with loss of body parts.
Never reach into the hazardous area while the
engine of the tractor with connected universal
joint shaft/hydraulics/electronic system is
running.

General safety instructions
KG 4/5/6001-2 BAH0060-5 12.17 19
MD 079
Risk of materials or foreign objects being
flung away from or out of the implement
when entering or remaining in the danger
area of the implement!
These dangers can inflict severe injuries on all
parts of the body.
Stay well clear of the danger area of the
implement.
Ensure that all persons maintain a sufficient
safety distance from the danger area of the
implement as long as the tractor engine is
running.
MD 081
Risk of crushing the entire body due to
necessary periods spent under unsecured
machine parts raised by lifting cylinders.
Causes serious, potentially fatal injuries
anywhere on the body.
Secure the lifting cylinder against inadvertent
lowering before entering the danger zone
beneath the raised implement components.
To do this, use the mechanical support device or
the hydraulic locking device for the lifting
cylinder.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.
Make sure that nobody is riding on the
implement.

General safety instructions
20 KG 4/5/6001-2 BAH0060-5 12.17
MD 084
Risk of crushing the entire body due to
standing in the swivel range when implement
parts are being lowered.
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to stand in the swivel range of
the implement when implement parts are
being lowered.
Instruct personnel to leave the swivel range
of any implement parts which can be
lowered before you lower the parts.
MD 086
Risk of crushing the entire body due to
necessary periods spent under raised,
unsecured machine parts.
Causes serious, potentially fatal injuries
anywhere on the body.
Before spending time in the danger area
underneath raised implement parts, secure the
raised parts to prevent them from being
accidentally lowered.
To do this, use the mechanical support device or
the hydraulic locking device.
MD 087
Risk of cutting or severing of toes or feet
through direct contact with moving parts
involved in the working process!
This hazard can cause the most severe injuries
with loss of body parts.
Stay well clear of the danger area when the
tractor engine is running with the universal joint
shaft or hydraulic/electrical system connected.