Ambient TOUCH LIGHT Operating instructions

50D0093 Rev 3 May 2005 Page 1 of 11 Ambient Technologies
ADivision Of
TLT
TOUCH LIGHT™ Thermostatic On/Off Remote Control
INSTALLATION AND OPERATING INSTRUCTIONS
This wireless thermostatic on/off/ remote control – system provides a safe, reliable, and user-friendly remote control
for millivolt valve gas appliances. The system can be thermostatically or manually turned on and off with the
transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding
accessory installation before connecting this remote control system.
Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the
dealer from whom you purchased the kit. Do not attempt to install any part of the kit unless all parts are in good
condition. Please keep this booklet for future reference.
CONTENTS OF KIT
Description Qty
Touch Light Transmitter 1
Battery Alkaline AA (for Transmitter and receiver) 6
Receiver (Assembly) consists of : 1
Receiver Box
Slide Button-Black (On/RS/Off)
L-Bracket (Floor Mount)
Wall Cover Plate-Black 1
Wall Cover Plate-White 1
Slide Button-White (On/RS/Off) 1
Screws (for Wall Cover Plate) 2
Plug-In Wiring Assembly – 18” Inches 1
Velcro (Loop and Hook) 1
Wall Anchor Screws 2
Wall Anchor 2
Installation Instructions
Screws (for fireplace system control covers)
Wall Bracket
1
2
1
FEATURES/SPECIFICATIONS
•Contemporary Ergonomic Table Top or Wall Mount Transmitter with Large LCD Display
•Easy Access Thermostatic Control
•Battery Powered Transmitter and Receiver
•Easy Access Battery Door
•Pre-Programmed for Quick Installation
•Low battery Indication
•Child Proof Lock-out
•16 Security Codes
•2 hour Shut Down (Optional)
•Thermal Safety Shutdown (Transmitter Only)
•Quick Disconnect Wiring Assembly
•Reset Button
WARNING

50D0093 Rev 3 May 2005 Page 2 of 11 Ambient Technologies
ADivision Of
Important Safety Information
•Read this manual thoroughly prior to installing, programming or operating any remote control.
•This remote control system is designed for use with a millivolt gas valve system. Do not use this remote
control system on applications with voltages above 24 Volts DC and 1 amp current.
•This remote control system requires two (2) “AA” alkaline batteries for the transmitter and four (4) “AA”
alkaline batteries for the receiver.
•Wiring must conform to appliance requirement and building codes/ordinances as required by local and
national code authorities having jurisdiction.
•Do not short (or jumper) across the gas valve terminals to test the remote control installation. This could
damage the unit and void the warranty.
•This remote control system should only be used as described in this manual. Any other use is not
recommended and will void the warranty.
NOTE
Due to the sensitive temperature monitoring components in the transmitter, it is necessary to
allow the transmitter to stabilize to room temperature before accurate room temperatures are
displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for
accurate temperature readings to appear on the LCD.
WARNING
Turn appliance OFF and allow to cool before installing or servicing. DO NOT connect
110-120 VAC wiring to the milli-volt gas control valve. The remote operator must be installed
exactly as outlined in these instructions. Read all instructions completely before attempting
installation. Follow instructions carefully during installation. Any modification of
components will void the warranty and may cause a fire hazard.
WARNING
Turn appliance OFF (at the appliance or remote receiver) if you are away from your house for
a long period of time. Never leave anything on top of the surface on the touch light
transmitter.
INSTALLATIONS

50D0093 Rev 3 May 2005 Page 3 of 11 Ambient Technologies
ADivision Of
L-Bracket
Slide Switch
Batter
y
Door
Remote Receiver:
The remote receiver may be wall mounted or installed in the appliance per the
appliance homeowner’s manual. Refer to the Homeowner’s Manual for special
installation instructions. If wall mounted, the remote receiver must be installed in a
junction box with cover plate provided. Failure to follow the installation instructions
found in the appropriate Homeowner’s Manual will void the warranty and may cause
a fire hazard.
Installing Batteries:
The remote receiver uses four (4) “AA”- size batteries. To install batteries,
1. Remove the slide switch by gently pulling straight out.
2. Use your thumb and index finger to gently pull down the L-bracket.
3. Open the battery door by pressing the two tabs located on the door.
4. Install the batteries as indicated in the receiver cover.
5. Close the battery door until the door tab snaps in place.
6. To install the receiver into a wall junction box, install the receiver with the
screws provided .
7. If you decided to install the receiver into the appliance, reinstall the L-
bracket.
8. Gently, install the slide switch back to the receiver stem.
9. The batteries should be replaced at least once every 6 months or when the battery indicator flashes.
Connecting the Receiver to your appliance:
This system comes with an 18 inch wire assembly. Insert the white terminal to the back of the receiver. The
terminal wire block can only be installed one way. Do not force the terminal plug onto the receiver.
Connect the wiring terminal two (2) _” female spade terminals to the appliance. Refer to the appropriate
Homeowner’s Manual for proper wiring connections to the appliance. Your appliance may have other options to
connect wiring from receiver. For applications longer than 18 inches, use 18 gauge wire, 105ºC rated, with no
splices. Connect to the two (2) 1/4“ female spade wiring terminals. Wire can be no longer than 20 feet.
WARNING
Make sure that the wires do not contact the appliances any place other than at the terminals.
Exposure to temperatures higher than 105C (250ºF) may cause the receiver to malfunction or
fire hazard.
Touch Light Transmitter:

50D0093 Rev 3 May 2005 Page 4 of 11 Ambient Technologies
ADivision Of
Installing Batteries:
The Touch Light transmitter uses two (2) “AA”- size batteries. To install
batteries,
1. Press down the battery door tab and lift up and remove the
battery door.
2. Install the battery.
3. Close the battery door by snapping in place.
4. Repeat the above step for the other battery.
5. When both batteries are installed, the transmitter will
initialize for 10 seconds and then is ready for use.
6. The batteries should be replaced at least once every 6
months or when the battery icon indicator flashes.
Setting Privacy (DIP) Switch on Receiver and Transmitter:
The remote receiver and transmitter privacy (DIP) switches are preset at the factory. In the event of activation or
interference from other nearby transmissions, reset the code using the following procedure:
1. Slide the code switches on the transmitter or receiver to your choice of ON or OFF position. Switches #1
to #4 are preset to “ON” for both the transmitter and receiver.
2. The switches on the transmitter and receiver must match in order for the system to work.
3. To check, touch the transmitter groove surfaces for at least 1 second and, the transmitter will emit a beep,
and the receiver indicator light will blink. If not repeat step 2.
4. The system is now ready to operate.
WARNING
Do not use two (2) or more remote control systems in the same area with the same dip switch
settings, as they will communicate with each other. This may cause the appliances to
malfunction.
Optional Auto Shutdown:

50D0093 Rev 3 May 2005 Page 5 of 11 Ambient Technologies
ADivision Of
1. The Touch Light transmitter comes preset from the factory with a 2 hour shutdown from its last ON
operation. This is done to prevent the appliance from continuing to run if unattended.
2. You may disable this feature if you wish. To disable, change the Touch Light transmitter privacy (DIP)
switch #1 ONLY to the OFF position (by sliding the switch towards the battery door.) Make sure the
receiver privacy (DIP) switches are set the same. Follow the instructions on how to set the privacy (DIP)
switch setting.
3. By disabling this feature, your appliance may continue to run unattended.
Reset Button:
1. The reset button can be used to reset the transmitter if transmitter is not working properly. The reset
button is located behind the battery door cover. Using a paper clip, press the reset button and the transmitter
will reset and initialize for 10 seconds before it can be used.
Where to place Touch Light Transmitter?
1. The Touch Light transmitter is recommended to be placed on a
non metal table top or wall mount. Make sure there is no direct
contact of metal parts to the body of the transmitter.
2. If wall mount, choose a mouting location about 5 feet above the
floor in an area with good air circulation and away from the
following:
a. Air ducts
b. Radiant heat from the sun and appliances
c. Concealed pipes and chimneys
3. Align the wall bracket to the desired location. Mark two (2) holes
using the wall bracket as template.
4. Drill two (2) holes and insert the plastic anchors until they are flush
with the wall.
5. Fasten securely the wall bracket to the wall with the two (2) screws.
6. Refer to the figure on how to install the transmitter to the wall bracket.
OPERATIONS:

50D0093 Rev 3 May 2005 Page 6 of 11 Ambient Technologies
ADivision Of
Transmitter:
General:
The TLT has two operating modes. It can used as manual or thermostatic On/Off remote control system.
The transmitter will operate the remote receiver from 1foot to a maximum of 20 feet. The operational range is
reduced when batteries are low or when the receiver is inside a metal enclosure.
Initial start up:
1. After initial power up or reset button is pressed, the transmitter is reset.
2. During transmitter reset, all segments of the LCD will be turned on. After ten (10) seconds, the LCD will
be initialized and operational. You will hear a beep during this time.
3. After reset, only the room temperature will be displayed on the LCD display.
Manual Mode- On or Off Operation:
1. Since Touch Light transmitter is touch sensitive equipment, we recommend to use only your index finger to
touch. Do not use any metal object to contact or touch the surface. The transmitter will recognize a valid
touch if either side of the surface area are covered more than 10% for a period of at least 1 second
2. To activate a signal, you need to touch either side of the groove surfaces for at least 1 second and then
release your finger. If the touch is valid, it will beep once and a signal will be sent to the receiver. During
this time you will see the transmission icon on the LCD display for a brief time. No other command can
be given until the transmission is completed.

50D0093 Rev 3 May 2005 Page 7 of 11 Ambient Technologies
ADivision Of
Thermostatic Mode Operation:
1. Push down on the flip door button to access the thermostatic control.
2. Press the AUTO button to enter the thermostatic mode (Beep Once). “TSTAT” and SET temp icon will
appear on the lower LCD screen
3. In thermostatic mode, press the UP πbutton or θDOWN button to set the desired set temperature.
4. Once the setting is completed, the transmitter will automatically turn on the fireplace when the room
temperature is below the set temperature and turn off the appliance when the room temperature is above
the set temperature within 1 degree.
5. There will be a slight delay in the response of the unit (on/off) to a temperature. Room temperature is
monitored every 3 minutes.
6. All the manual on/off touch will be disabled the the transmitter is in thermostatic mode.
7. Press the Auto button to exit the thermostatic mode (beep once). The “TSTAT” and SET temp icon will
disappear on the lower LCD display. The transmitter will be in the manual on/off mode
Child-proof protection:

50D0093 Rev 3 May 2005 Page 8 of 11 Ambient Technologies
ADivision Of
1. Touch both sides of the groove surface with your two index fingers simultaneously for at least 3 seconds to
enter child-proof mode. Once you hear two (2) beeps and the child proof icon appears on the LCD display,
the child proof mode is activated. You will not able to turn the appliance on or off in this mode.
2. Always place both fingers on the middle of the groove surfaces to ensure a proper touch.
3. Child-proof protection is not available in Thermostatic mode.
4. To deactivate child proof, repeat step 1. You will hear two (2) beeps and the child proof icon will
disappear.
Safety Touch Auto Shut Off:
1. If a metal object, (i.e. car key) or your hand is resting continuously for more than ten (10) seconds on either
side or both side of the groove surfaces , the transmitter will emit three (3) beeps and send an off signal to
turn off the appliance. Once the object is removed from the groove surfaces, the transmitter will remain
in the off state until your next valid touch. Never leave anything on top of the surface of the touch light
transmitter to prevent undesirable operation.
2. This feature will be disabled in Thermostatic mode.

50D0093 Rev 3 May 2005 Page 9 of 11 Ambient Technologies
ADivision Of
Low-battery detection:
1. Battery voltage is checked once
a minute. When the battery
voltage drops to a certain level,
the low-battery warning will
come on, and the transmitter
will emit three (3) beeps and
send signals to turn off the
appliance. The transmitter will
not function anymore until new
batteries are installed. If the
battery is too low, the three (3)
beeps may not be heard.
2. When the batteries are low, the
LCD shows a blinking low
battery indicator.
3. Change the battery every six
months before the battery is too
weak for normal operation. TURN THE UNIT OFF BEFORE REPLACING BATTERIES.
Touch Light Transmitter Thermal Shutdown:
1. If transmitter measures a room temperature
exceeding 99 degrees Fahrenheit, the LCD will
display “HI”, emit three (3) beeps and send an
off signal to turn off the appliance.
2. Transmitter will not function until the room
temperature has dropped below 99 degree
Fahrenheit.
3. If transmitter measures a room temperature less
than 40 degrees Fahrenheit, the LCD will
display “LO”, and no signals will be sent to
turn on the appliance.
Receiver:
Slide Switch:
1. ON position: the system will remain on until the slide switch is placed in the OFF or RS position.
2. RS position: the system will only operate if the remote receiver receives a signal from the transmitter.
3. OFF position, the system is off. The slide switch should be placed in the OFF position if you will be
away for an extended period of time. If the remote receiver is mounted out of children’s reach, the OFF
position also functions as a safety device by both turning the system off and rendering the receiver
inoperable.
TESTING YOUR NEW REMOTE CONTROL SYSTEM
1. Light your gas appliance following the appliance lighting instructions that came with the appliance.
Confirm that the pilot light is on; it must be in operation for the remote control to operate the main gas
valve. Appliance control knob must be in the ON position. Appliance ON/OFF switch must be in OFF
position.
2. Slide the 3 position button on the remote receiver to the ON position. The main gas flame should ignite.

50D0093 Rev 3 May 2005 Page 10 of 11 Ambient Technologies
ADivision Of
3. Slide the button to OFF. The flame should extinguish (the pilot light will remain on).
4. Slide the button to RS (the center position), then touch the transmitter to turn the system to ON. The main
gas flame should ignite.
5. Touch the transmitter to turn the system to OFF. The flame should extinguish (the pilot light will remain
on).
TROUBLESHOOTING
Symptom Causes Action
1. LED light on
receiver blinking or
battery icon on LCD
on transmitter.
2. LCD display is
blank
3. LCD display shows
“funny” display
1. Low Battery 1. Replace batteries. Change
batteries every 6 months.
2. Check battery installation and
replace batteries.
3. Press Reset button at the back of
the transmitter.
4. Appliance does not
come on after a valid
touch (beep)
1. Wiring / Electrical Connections 1. Slide the switch to ON, if
appliance comes ON, wiring is not
the cause.
2. If appliance does not come on,
check wiring connections.
2. Privacy (DIP) switch setting on transmitter
does not match receiver
1. Make sure the transmitter and
receiver have the same DIP switch
settings.
3. Transmitter measures temperature exceeding
99 degrees Fahrenheit and shows “HI” on LCD
1. Move transmitter to a cooler
place and wait until temperature
drops below 99 degree.
4. Distance between the transmitter and receiver
is more than 20 feet
1. Make sure the operating distance
is less than 20 feet
5. Receiver cannot
receive signal.
1. Receiver is installed in an enclosure 1. Make sure the receiver is not
located inside an enclosure.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.

50D0093 Rev 3 May 2005 Page 11 of 11 Ambient Technologies
ADivision Of
WARRANTY
This warranty gives you specific legal rights and you may also have other rights that vary from
state to state or province to province. Answers to any questions regarding our limited warranty may be obtained by
writing our corporate offices.
Ambient Technologies warrants each new Ambient Technologies remote control against any defects that are due to
faulty material or workmanship to the original owner, for a period of five years after the original date of purchase.
This warranty and our liability does not apply to batteries, nor does it include damage to merchandise or the remote
control resulting from accident, alteration, neglect, misuse, improper installation or any other failure to follow
Ambient Technologies installation and operating instructions.
Ambient Technologies agrees to repair or replace at its option any Ambient Technologies remote control under
warranty provided it is returned postage prepaid to our warranty facility in a padded carton within the warranty
period, with proof of the original date of purchase and a brief description of the malfunction. This limited warranty
does not include the cost of removal or re-installation.
Ambient Technologies
149 Cleveland Drive
Paris KY 40361
FOR TECHNICAL SUPPORT
CALL 800-398-6195