Ambir ImageScan Pro 960u User manual

Ambir ImageScan Pro 960u
High Speed Document Scanner with
UltraSonic Misfeed Detection
®
User Guide
www.ambir.com
Ver 1.2p/n UG960u-1.2

Ambir ImageScanPro®960u
1.Scanner
2.USB Cable
3.AC Adapter
4.Paper Chute
5.Installation Guide
6.Calibration Sheet
7.Cleansing Cloth
Box Contents
Guide
Table of Contents
Box Contents
Installation and Setup
Loading Documents
Scanning
Calibration
Cleaning the ADF
Replacing the Pad Module
Clearing Paper Jams
Scanner Connection
LED Indication
Ultrasonic Sensor
2
3,4
5
6,7,8,9
10
10
11
11
12
12
12
8.Feed Pad
2
User
p/n UG960u-1.2

Ambir ImageScan Pro®960u
Installation and Setup
Step 1. Install the Paper Chute
1. Open the ADF cover by pulling the lever.
gnitresnidnagningilaybetuhcrepapehtllatsnI.2
the tabs of the paper chute into their slots on the
scanner.
nwodkcabtignihsupybrevocFDAehtesolC.3
until it snaps back into place.
Step 2. Connecting the Scanner to
Your Computer
1. Plug the AC adapter into the scanner’s power
rotpecer .
2. Plug the other end of the AC adapter into a
.teltuorewopCAdradnats
elbacBSUdedulcniehtfodneerauqsehtgulP.3
to the USB port at the rear of the scanner.
4. Plug the rectangular end of the USB cable to an
available USB port on your computer.
3
GuideUser
p/n UG960u-1.2

Ambir ImageScanPro®960u
Installation and Setup (Continued)
Step 3. Installing the Software
Visit www.ambir.com/900u-series-set to download your scanner driver
and AmbirScan ADF software.
>
4
GuideUser
p/n UG960u-1.2

Ambir ImageScan Pro 960u
5
1. Load the documents, and face down, toward the
center of the ADF paper chute and all the way into the ADF
until touching the bottom.
For single-sided scans, load the documents face down so
that the side to be scanned faces towards the paper chute.
For double-sided scans, load the desired page order of
documents face down so that the side to be scanned faces
towards the paper chute.
If you wish to scan both sides of a single page, the page need
only pass through the ADF once – you will need to set the
scan type to “Duplex.”
3. Adjust the paper width slider for the paper size
you are using. The paper width slider should be
gently touching both sides of the documents.
Attention
DO NOT load more than 100 sheets of paper (70 g/m2, 18 lb.) to the ADF.
Paper scanned from the ADF must be a minimum of 5.08 x 5.08 cm (2” x 2”, W x L).
Make sure there are no gaps between the document stack and the paper-width slider; otherwise,
the scanned images can be skewed.
,
they should never be wedged in so tightly that the process of feeding them through the scanner
is strained.
Do not load additional paper into the ADF while the unit is feeding and scanning.
LOADING DOCUMENTS
2. If you need to scan longer documents, pull
out the paper chute extension and stacker to
provide further support for the documents.
>
®GuideUser
p/n UG960u-1.2

Ambir ImageScanPro 960u
6
Scanning
There are three different ways to operate the scanner:
1. By acquiring images from the scanner through our TWAIN interface within any TWAIN-
compliant application programs.
2. By scanning from the buttons on the Scanner’s front panel.
3. By scanning from AmbirScan ADF’s Execute menu on the screen.
Scanning via TWAIN Interface
Select the Scan Source:
If you have more than one scanner or other imaging devices installed on your computer, you
need to set this scanner as the default scanning source before you acquire image data/scan
using a TWAIN compliant program.
®GuideUser
p/n UG960u-1.2

Ambir ImageScan Pro 960u
7
Scanning from the Scanner’s Front Panel
Completing scanning projects using the scanner buttons is easy and convenient. The number
assigned to a scanning task displayed on the scanner’s front panel is through AmbirScan
ADF. AmbirScan ADF offers you quick access to the most frequently-used scanning functions. They
are especially useful when you need to repeatedly scan with the same settings and send images to
the same destination. Before performing your scan via scanner buttons, the button
settings with your preferences.
Scan with Scanner Buttons
1. Place the document or images into the scanner.
2. Press the UP or DOWN button to select the desired task.
3. Press the Scan button.
The scanner starts to scan immediately and carry out the corresponding action according to settings in
the Button window.
Scanning (Continued)
®GuideUser
p/n UG960u-1.2

Ambir ImageScanPro 960u
8
Within the “Button window, you can a row of icons running through the left side of
the window. Each icon represents a scanning task, and the number underneath corresponds to the
function number displayed on the scanner front panel.
Nine (9) frequently-used scanning tasks are for your convenience. You may, however,
customize the settings of the nine tasks to best meet your needs and preferences.
Follow the steps below:
1. Do one of the following to open the Button window:
Double-click the icon in the Windows system tray.
Right-click the icon in the Windows system tray, and then choose
in the pop-up menu that opens.
2. Select a task number by clicking on the icon.
3. Select the desired function from the drop-down list of Button Template and adjust
button settings.
Click the Help button within the Button window for more information about the button settings.
Scanning (Continued)
GuideUser
®
p/n UG960u-1.2

Ambir ImageScan Pro 960u
9
View Button Settings
There are two ways to view the button settings:
1. Double-click the icon in the Windows system tray.
2. Right-click the icon in the Windows system tray, and then choose “Button
in the pop-up menu that opens.
Scanning from the AmbirScan ADF On-screen Execute Menu
You may also use AmbirScan ADF’s on-screen Execute menu to perform the same scanning tasks.
This program provides a quick and convenient way to perform various scanning functions.
Follow the steps below:
1. Place the document or images onto the scanner.
2. Right-click the icon in the Windows system tray, and then choose Execute in the pop-up menu
that opens.
3. Click the desired button function item in the pop-up menu. The scanner starts to scan
immediately and carries out the corresponding action according to the button you set.
Scanning (Continued)
®GuideUser
p/n UG960u-1.2

Ambir ImageScanPro 960u
10
Calibrate the scanner if colors appear in areas that should be white,
or colors of the scanned image and the original vary a lot. This allows
you to adjust and compensate for variations that can occur in the optical
component over time by its nature.
The following describes how to calibrate the scanner:
ehthtiw,rennacsehtfoFDAehtotniteehSnoitarbilaClaicepsehttresnI.1
arrow pointed toward the scanner buttons.
noitarbilaC>emanledomrennacsruoY>smargorPllA>tratSkcilC.2
Wizard.
etarbilaCkcilcneht,puspoptahtdraziWnoitarbilaCehtmorftxeNkcilC.3
Now....
.ssecorpnoitarbilacehtnigebotnottubtratSehtnokcilC.4
hcihw,rennacsehthguorhtteehsnoitarbilacehtslluprennacsehT.5
completes thecalibration process. After the calibration is complete, click
OK and then click Finish.
Calibration
Cleaning the ADF
1. Open the ADF cover by pulling the lever.
htiwdenepmadhtolcehthtiwsaeragniwollofehtepiwyltneG.2
the cleaner. Be careful NOT to scratch their surfaces.
Clean Feed Roller:
Wipe the Feed Roller from side to side and then rotate it. Repeat
this until its entire surface is cleaned.
Clean Pad Module:
Wipe the Pad Module from top to bottom (in the direction of
arrow shown in below picture). Be careful not to damage the
pick springs of the pad.
1. Wait for cleaned areas to dry completely.
spanstilitnunwodkcabtignihsupybrevocFDAehtesolC.2
back into place.
Have the following cleaning materials ready to clean the scanner:
soft, dry, lint-free cloth
DO NOT USE WATER
non-abrasive cleaner fluid: Isopropyl
rubbing alcohol(95%)
®GuideUser
p/n UG960u-1.2
taegderehtienoworranahtiwdekram,teehSnoitarbilaCdedulcniehT
960u.
®

Ambir ImageScan Pro 960u
11
1. Open the ADF cover by pulling the cover open lever.
dapehtfosedishtobgnihcnipybeludomdapehtevomeR.2
module. Pull it out.
ehtnosbatehtgnitresniybeludomdapwenehtllatsnI.3
module onto their slots on the scanner.
spanstilitnunwodkcabtignihsupybrevocFDAehtesolC.4
back into place.
Replacing the Pad Module
Clearing Paper Jams
If a paper jam in the ADF happens, please perform the following
steps:
1. Remove any unjammed documents still loaded into the ADF.
2. Open the ADF cover by pulling the cover open lever.
Try to avoid creasing or wrinkling the documents.
spanstilitnunwodkcabtignihsupybrevocFDAehtesolC.4
back into place.
®
p/n UG960u-1.2
GuideUser

Ambir ImageScanPro 960u
12
troubleshooting connection
problems with your scanner is
to check all physical connections.
The icon , located on
the Windows system tray,
indicates if the scanner software
is properly launched and the
scanner and computer are
communicating with each other.
Scanner Connection
LED Indication
The Power/Power
Saving LED and Warning
LED indicate different
scanner status.
When scanning a stack of documents by ADF, the ultrasonic
sensor detects multifeeds by checking paper overlap (i.e.,
2 or more pages stuck together when being fed through the
ADF). Clean the ultrasonic sensor lightly with a dry cloth if it is
necessary.
Ultrasonic Sensor
Appearance Status
The program has been successfully launched and
the scanner is connected with the computer, ready to
scan images.
The scanner is not connected with the computer, or the
scanner power is not switched on.
No Display You have chosen to terminate the program. The scanner
may or may not be connected to the computer.
Warning
LED Light
Power / Power
Saving LED Light Status
Off White The scanner is turned on, ready to
scan images.
Off Orange The scanner is in standby mode (sleep
mode) if it is idle for 10 minutes.
Red Blinking White The ADF cover is opened.
Blinking
Red White Paper jam.
Blinking
Red Off An internal component of the scanner may have malfunctioned.
Off Off
The scanner is off, either because the
power is not turned on, or because the
AC adapter is not properly plugged
into an AC power outlet.
®GuideUser
p/n UG960u-1.2

www.ambir.com
p/n UG960u-1.2