Ambirad TORNADO User manual

WARNINGS
1 This appliance must only be installed by a competent person in accordance with
the requirements of the Codes of Practice or the rules in force.
2 All external wiring MUST comply with the current IEE wiring regulations.
3 Warning this appliance must be earthed.
TORNADO
GAS FIRED MOBILE HEATER
REMOTE THERMOSTAT & DUCTING OPTIONS
Instruction Manual.
INDEX
Introduction ---------------------------------------------------------------------- 1
Options Available --------------------------------------------------------------- 2
Fitting Instructions -------------------------------------------------------------- 3
Section

This document describes the fitting of the ducted
options and remote thermostat option available for
the Tornado heater.
This instruction is intended for sole purpose of
use as indicated.
The information contained within this instruction
sheet is for use with Ambi-Rad products within the
country of use and in accordance with the rules in
force and by a competent person based on cur-
rent HSE guidelines.
Introduction.
PLEASE READ this document prior to installation
and operation to familiarise yourself with the com-
ponents and any tools you require at the various
stages of assembly.
The manufacturer reserves the right to alter
specifications without prior notice.
This appliance must be installed in accordance
with such regulations as are in force.
This appliance conforms to IP44 of IEC 34-5.
Subject to compliance to clearance distances,
ventilation and flue requirements detailed in these
instructions the heater can be used inside mar-
quees.
Only use in a well ventilated area.
The heater is not for domestic use.
The heater is designed for space heating only.
Do not use the heater in basements or below
ground level.
This appliance is fitted with a hose and regulator.
These instructions must be given to the user.
Observe the cool down period and never handle
the heater when hot.
Never place any objects, particularly combustible
materials on top of the heater and always ensure
that flues are not obstructed.
For your own safety we recommend the use of
personal protective equipment when fitting any of
the options described in this document.
Bend knees when lifting the product via the han-
dles for wheeling.
Important, please read.
Options available.
There are four ducting options and a remote
thermostat option available, as follows:
1: Flue duct kit, 5m long, Ambirad part No.
200584.
2: Ducted air kit, 5m long, Ambirad part No.
201847.
3: Air delivery duct kit, 10m long, Ambirad part
No. 201848.
4: Flue duct extension kit, 5m long, Ambirad part
No. 200594.
5: Remote thermostat kit c/w cable and mounting
bracket, Ambirad part No. 200587.

Fitting Instructions.
Spigot
100mm tubing
Fig.1
Fig.2
Fig.3
1: Flue duct kit (Fig.1).
Fit flue duct spigot into tube and tighten hose
clip as shown in Fig.2.
Push spigot firmly into flue duct outlet on the
right hand side of the heater as shown in Fig.3.
IMPORTANT: Ensure the heater is switched off
and cooled sufficiently before removing flue
duct after use.
Fig.4
Spigot
150mm tubing
2: Ducted air kit (Fig.4).
Fig.5
Fit air inlet duct spigot into tube and tighten hose
clip as shown in Fig.5.
Push spigot firmly into the air inlet hole on the
left side of the heater as shown in Fig.6.
Fig.6

Fitting Instructions cont.
3: Air delivery duct kit (Fig.7).
Fig.7
Fig.8
Slide the BLACK end of the air delivery duct with
clip over the air outlet of the heater as shown in
Fig.8.
Fig.9
Secure the air delivery duct using the quick
release clip as shown in Fig.9.
IMPORTANT: Ensure the heater is switched off
and cooled sufficiently before removing air deliv-
ery duct after use.
4: Flue duct extension kit (Fig.10).
Fig.10
Fig.11
Fit the coupler into the end of the flue duct and
tighten the hose clip as shown in Fig.11
Fig.12
-
Fit the extension duct onto the other end of the
coupler and tighten the hose clip as shown in
Fig.12
IMPORTANT: Ensure the heater is switched off
and cooled sufficiently before removing flue
duct extension after use.

Fig.13
5: Remote thermostat kit (Fig.13).
Fig.14
Fig.14 shows the remote thermostat socket and
selector switch on the rear panel of the heater.
Socket
Selector switch
Fig.15
Fit the remote thermostat plug into the socket
on the rear panel as shown in Fig.15. The
selector switch should now be moved to the
“remote stat” position. The thermostat can now
be sited and the desired operating temperature
set.
Fitting Instructions cont.

Notes.

Notes.

Notes.
AmbiRad Limited Fens Pool Avenue
Brierley Hill West Midlands DY5 1QA
United Kingdom.
Telephone [phone]
Facsimile 01384 489707
Email [email protected]
Website www.ambirad.co.uk
Technical Support www.s-i-d.co.uk
AmbiRad is a registered trademark of AmbiRad Limited. Because of continuous product
innovation, AmbiRad reserve the right to change product specification without due notice
Document reference number GB/TOR/175/1107