AMCI PressPro Genesis Installation and operating instructions

20 Gear Drive, Plymouth Industrial Park, Terryville, CT 06786 page: 1
Tel: [phone] Fax: [phone] Web: www.AMCI.com
PressPro Genesis Manual Addendum
The following document contains information that is not contained in the standard PressPro
Genesis manual.
Fault Stop Output
The fault Stop output is typically on. That is, the output will turn off when a fault condition is
detected. The following is the list of conditions that will cause the Fault Output to turn off.
¾If a fault condition is detected on one of the Die Monitoring inputs. This assumes that the
Die Monitoring input has been configured to use the Fault Stop output.
¾A fault is detected on the Brake Input
¾If a Transducer Fault is detected
Additional Configuration Parameters
Eight parameters can be programmed on Configuration Screen 4 of 4. These parameters, along
with their function and default values, are shown in the following tables.
C O N F I G U R E 4 O F 4
C L E A R F A U L T S N O
V I E W * * P : * * * S P M * * * *
To move from one parameter to the next, move the blinking cursor over the parameter and press
the SELECT key. When the desired parameter is reached, press the ENTER or ¾arrow key to
move the cursor to the next data field, where the SELECT key is used to select between NO and
YES.
Parameter Function Default
Clear Faults If “YES”, a user with an Operator Level access is allowed to clear
any faults that occur. NO
Select Tool # If “YES”, a user with an Operator Level is allowed to change
which program is currently running. NO
INC / DEC If “YES”, a user with an Operator Level is allowed to Increment
or Decrement the Limit Switch On/Off setpoints NO
Clear Counters
If “YES”, a user with an Operator Level access is allowed to clear
the Actual Batch and Total counters. Regardless of the setting,
only a user with Master or Setup level access are allowed to clear
the Tool and Stroke counters.
NO
Brake Monitor
If “YES”, it allows the Brake Monitoring functions to occur. Any
transitions on the Brake Input will be ignored if this parameter is
set to “NO.”
NO
Motion Detect If “YES”, it allows the Motion Detect operations to occur. Motion
detect errors will not be reported if this parameter is set to “NO.” NO
Latch Transd Err
If “YES”, the Genesis unit will remain in transducer fault until it is
cleared by the user. If set to “NO” the transducer fault will clear
as soon as the resolver signals become valid.
YES
Count Input 1
If “YES” the batch counter will increase whenever input 1
transitions. If “NO” the batch counter will increase when the
resolver’s position data passes through the zero point.
NO

20 Gear Drive, Plymouth Industrial Park, Terryville, CT 06786 page: 2
Tel: [phone] Fax: [phone] Web: www.AMCI.com
PressPro Genesis Manual Addendum
Solid State Outputs
There are two versions of the PressPro Genesis, one with Mechanical Relay Outputs, the GN3B1-
01A-00, and one with Solid State Relay Outputs, the GN3B1-01B-00. The standard user’s
manual covers only the Mechanical Relay output.
The functions of the PressPro Genesis with Solid State relays are the same as those of a unit with
Mechanical relays.
The following diagram shows the location of the inputs and outputs on the GN3B1-01B-00 Solid
State version.
Note: The solid state relays used with the GN3B1-01B-00 are not included with the unit and
must be ordered separately. The two options are KD-6 (DC relays) or KA-3 (AC relays).
Solid State Relay Wiring
Each Relay output has two terminals. One is labeled +and the other that shows the Output
Number or Function. Connect your power supply to the +terminal and your load to the other
terminal.
file: Genesis_press_pro_addendum
date: 1/25/06
+ 1 + 2 Out
p
ut Numbe
r
Power
Supply
+
COM
Load