AME 14461 User manual

2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: [phone] Toll Phone: [phone]AME (4263)
Fax: [phone] E-mail: [email protected] www.ameintl.net
INSTRUCTION MANUAL
& PARTS BREAKDOWN
Read this manual and follow all the safety rules and operating instructions before using this product.
# 14461
20 TON LOW PROFILE AIR
HYDRAULIC BOTTLE JACK

2
WARNING!!
FAILURE TO READ THESE
WARNINGS MAY RESULT IN
PROPERTY DAMAGE AND
OR PERSONAL INJURY.
Use as lifting device only.
Use only on hard, level surface.
Support load by appropriate means after
lifting.
Do not exceed rated capacity.
Do not modify jack.
Center load on the jack.
Only use attachments and/or adapters
supplied with or sold specially for the
jack.
Only lift areas of the vehicle designed by
the vehicle manufacturer.
Failure to comply with all of these warnings
may result in loss of load, damage to
jack, and/or failure resulting in
personal injury or property damage.
Owner/Operator Responsibility
It is the owner/operator responsibility to properly use and maintain this
equipment and the legibility of all warnings and instruction labels.
Carefully read and understand the instructions and warnings in this
manual before operating this equipment. Keep this manual in a safe
location for future reference.
Warranty of this unit will be void on any part if the unit subjected to
misuse due to overloading, abuse, lack of maintenance and unauthorized
modifications. No warranty – verbal, written or implied – other than the
official, published AME new machinery and equipment warranty will be
valid with this unit. In addition, it is your responsibility to be aware of
existing Federal, State and Local codes and regulations governing the
safe use and maintenance of this unit.
Inspection
Prior to each use, visually inspect for leaking hydraulic oil, damaged,
loose or missing parts. If jack is worn or damaged, remove from
service and contact your nearest service center for repair.
Maintenance
Check oil level. With the jack in an upright position and the ram
completely retracted, open the release valve (turn counter-clockwise) and
remove the filler plug. The oil level should be just up to the hole. Fill if
necessary with clean hydraulic jack oil.
Lubricate internal components. With the release valve open, pump the
jack for a while. Purge the hydraulic system of air. During transit the unit
may become “air-bound”, causing a spongy ram action. To purge the
system, close the release valve (turn clockwise). Pump the jack to full
height. Open the release valve and push down on the ram. Repeat these
steps if necessary to completely purge the system.
Keep the jack clean. Occasionally lubricate the handle socket pivot
point, extension screw, release screw thread, and air valve to prevent
corrosion.
INSTRUCTION MANUAL
Lifting Capacity
(Ton)
Max. Height
(mm)
Min. Height
(mm)
Gross Weight
(kg)
Net Weight
(kg)
Air Pressure
(Mpa)
Package Size
(mm)
20 259 148 11 10 0.7-1.0 355X165X165

3
USE JACK FOR LIFTING ONLY. LOAD MUST BE
SUPPORTED IMMEDIATELY BY OTHER APPROPRIATE MEANS.
1. Jack operation is controlled by external air pressure. Connect
to an external air pressure source (clean connections prior to
assembly).
2. To raise the jack, turn the release valve clockwise until tight
and while connected to an air supply depress the air valve.
3. To lower the jack turn the release valve counter-clockwise
slightly and very slowly. Be careful not to turn valve quickly or
more than twice, otherwise, dangerous sudden lowering may
occur.
INSTRUCTION MANUAL

4
INSTRUCTION MANUAL

5

6
INSTRUCTION MANUAL
Service: Contact your nearest authorized service center for repairs and/or replacement parts.
2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: [phone] Toll Phone: [phone]AME (4263)
Fax: [phone] E-mail: [email protected] www.ameintl.net