probst SDH-H-15 User manual

5480.0002
V5
GB
Operating Instructions
Translation of original operating instructions
Hydraulic Manhole Cover Lifter SDH-H
SDH-H-15

Bitte beachten Sie, dass das Produkt ohne vorliegende Betriebsanleitung in Landessprache nicht
eingesetzt / in Betrieb gesetzt werden darf. Sollten Sie mit der Lieferung des Produkts keine
Betriebsanleitung in Ihrer Landessprache erhalten haben, kontaktieren Sie uns bitte. In Länder der
EU / EFTA senden wir Ihnen diese kostenlos nach. Für Länder außerhalb der EU / EFTA erstellen wir
Ihnen gerne ein Angebot für eine Betriebsanleitung in Landessprache, falls die Übersetzung nicht
durch den Händler/Importeur organisiert werden kann.
Please note that the product may not be used / put into operation without these operating
instructions in the national language. If you did not receive operating instructions in your national
language with the delivery of the product, please contact us. In countries of the EU / EFTA we will
send them to you free of charge. For countries outside the EU / EFTA, we will be pleased to provide
you with an offer for an operating manual in the national language if the translation cannot be
organised by the dealer/importer.

Contents
2 / 15
5480.0002
V5
GB
Contents
1EC-Declaration of Conformity ............................................................................................................................... 3
2Safety...................................................................................................................................................................... 4
2.1 Safety symbols................................................................................................................................................4
2.2 Safety Marking................................................................................................................................................4
2.3 Definition skilled worker / specialist ..............................................................................................................4
2.4 Personal safety requirements ........................................................................................................................ 5
2.5 Protective equipment..................................................................................................................................... 5
2.6 Accident prevention ....................................................................................................................................... 5
2.7 Function Control............................................................................................................................................. 5
2.7.1 General ....................................................................................................................................................... 5
3General.................................................................................................................................................................... 6
3.1 Authorized use................................................................................................................................................6
3.2 Survey and construction ................................................................................................................................ 7
3.3 Technical Data................................................................................................................................................. 7
3.4 Accessories .....................................................................................................................................................8
4Operation ............................................................................................................................................................... 9
4.1 Attaching Variants ..........................................................................................................................................9
4.2 Device Operating ........................................................................................................................................... 11
5Maintenance and care .......................................................................................................................................... 13
5.1 Maintenance ..................................................................................................................................................13
5.1.1 Mechanical .....................................................................................................................................................13
5.2 Repairs ...........................................................................................................................................................13
5.3 Safety procedures .........................................................................................................................................14
5.4 Hints to the type plate...................................................................................................................................15
5.5 Hints to the renting/leasing of PROBST devices ..........................................................................................15

EC-Declaration of Conformity
3 / 15
5480.0002
V5
GB
1EC-Declaration of Conformity
Description:
Type:
Order number:
Hydraulic Manhole Cover Lifter SDH-H
SDH-H-15
5480.0002
Manufacturer:
Probst GmbH
Gottlieb-Daimler-Straße 6
71729 Erdmannhausen, Germany
[email protected]
www.probst-handling.de
The machine described above complies with the relevant requirements of the following EU directives:
EC-machinery directive 2006/42/EC
The following standards and technical specifications were used:
DIN EN ISO 12100
Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
DIN EN ISO 13857
Safety of machinery - safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
Authorized person for EC-documentation:
Name: J. Holderied
Address: Probst GmbH; Gottlieb-Daimler-Straße 6; 71729 Erdmannhausen, Germany
Signature, information to the subscriber:
Erdmannhausen, 19.07.2018..........................................................................
(M. Probst, Managing director)

Safety
4 / 15
5480.0002
V5
GB
2Safety
2.1 Safety symbols
Danger to life!
Identifies imminent hazard. If you do not avoid the hazard, death or severe injury will result.
Hazardous situation!
Identifies a potentially hazardous situation. If you do not avoid the situation, injury or damage to property
can result.
Prohibition!
Identifies imminent a prohibition. If you do not avoid the prohibition, death and severe injury, or damage to
property will result.
Important informations or useful tips for use.
2.2 Safety Marking
WARNING SIGN
Symbol
Meaning
Order-No.:
Size:
Danger of squeezing the hands.
2904.0221
2904.0220
2904.0107
30 mm
50 mm
80 mm
REGULATORY SIGN
Symbol
Meaning
Order-No.:
Size:
Each operator must have read and understood the operating
instructions (and all safety instructions).
2904.0665
2904.0666
30 mm
50 mm
2.3 Definition skilled worker / specialist
Only skilled workers or specialists are allowed to carry out the installation-, maintenance-, and repair work on this device!
Skilled workers or specialists must have for the following points (if it applies for
this device), the necessary professional knowledge.
for mechanic
for hydraulics
for pneumatics
for electrics

Safety
5 / 15
5480.0002
V5
GB
2.4 Personal safety requirements
Each operator must have read and understood the operating instructions (and all safety instructions).
Only qualified, authorized personal is allowed to operate the device and all devices which are connected
(lifting device/carrier).
The manual guiding is only allowed for devices with handles.
2.5 Protective equipment
The protective equipment must consist, according to the safety regulations
of the following parts:
Protective clothing
Safety gloves
Safety shoes
2.6 Accident prevention
The workplace has to be covered for unauthorized persons, especially children.
Take care in case of thunderstorm!
The workplace has to be sufficiently illuminated.
Take care with handling wet, dirty and not solidified components.
The working with the device in case of atmospheric editions under 3 °C (37,5 °F) is forbidden!
Because the goods could be fall down caused by dampness or freezing.
2.7 Function Control
2.7.1 General
Before using the device check the functions and the working condition.
Maintenance and lubrication are only permitted when device is shut down!
Do not use the device, until all faults which can cause safety hazards are removed.
If there are any cracks, splits or damaged parts on any parts of the device, immediately stop using it.
The operating instructions must be available at the workplace every time.
Do not remove the type plate of the machine.
Unrecognisable information signs (such as regulatory or prohibition signs) must be replaced.

General
6 / 15
5480.0002
V5
GB
3General
3.1 Authorized use
The device (SDH-H) is exclusively suitable to lift and move all common sizes of covers.
The pulling force of covers is enough up to maximally 1500 kg (3,300 lbs).
Various keys and spreader bars are accessories.
The pulling force of 1,500 kg (3,300 lbs) of the device (SDH-H) may not be exceeded!
The device is only designed for the use specified in this documentation.
Every other use is not authorized and is forbidden!
All relevant safety regulations, corresponding legal regulations, especially regulations of the declaration
of conformity, and additional local health and safety regulations have to be observed.
Prior to every operation the user must ensure that:
The equipment is suited to the intended operation, the functioning and the working condition of the
equipment is examined, and the load is suitable to be handled.
Any doubts about instructions should be raised with the manufacturer prior to use.
NOT ALLOWED ACTIVITIES:
Unauthorized alterations of the device and the use of any self-made additional equipment could cause
danger and are therefore forbidden!
Never exceed the carrying capacity and the nominal width/nominal size of the device.
All unauthorized transportations with the device are not allowed:
Transportation of people and animals.
Transportation of other loads and materials than described in this manual.
Never suspend any goods with ropes, chains or similar at the device.

General
7 / 15
5480.0002
V5
GB
3.2 Survey and construction
SDH-H
3.3 Technical Data
Type
Max. wheel span
Hook centres
min./max.
Lifting height
Pulling force
Dead weight
SDH-H-15
1,050 mm (41“)
260/950 mm
(10¼/37½″)
310 mm (12¼″)
1,500 kg (3,300 lbs)
36 (80 lbs)
Handle
Hook for
covers
Support wheel
Holder of
support wheel
Hydraulic hand
pump
Main grider
Cross grider
Eyeybolt
Lifting rod at hydraulic
hand pump

General
8 / 15
5480.0002
V5
GB
3.4 Accessories
Key A
Key B
Key C
Spreader bar „small“
Spreader bar „large“
Type
Description
Order-No.
Keys and spreader bars
Key A
44800019
Key B
44800020
Key C
44800017
Spreader bar „small“
44800008
Spreader bar „large“
44800018
Set of keys and spreader bars UK
2 keys A, 2 keys B, 4 keys C, 1 Spreader bar „small“, 2
Spreader bars „large“
54800004
Tool and Equipment Box WZK
Size 1.200 x 550 x 630 mm to stow the complete
device(SDH-H) including all accessories.
42200107
There are always two keys necessary for lifting.

Operation
9 / 15
5480.0002
V5
GB
4Operation
4.1 Attaching Variants
Depending upon form, kind and execution of the covers, the suitable hooks (A or B) , and/or spreader bars(variant I or II) must
be selected.
HOOK A HOOK B
Hook A (2x44800019)
Hook B (2x44800020)
VARIANT I
Spreader bar „small“ (44800008)
Spreader bar „small“ (44800008) + Hook C (44800017)
+ 
Hook C (4x44800017)

Operation
10 / 15
5480.0002
V5
GB
VARIANT II
Spreader bar „large“ (2x44800018)
Spreader bar „large“ (44800017) + Hook C (44800017)
+ 
Hook C (4x44800017)

Operation
11 / 15
5480.0002
V5
GB
4.2 Device Operating
Prepare spreader bars and/or hooks suitably the cover,
which is to be raised.
Drive with the device (SDH-H) over the cover and hang
up the hooks (A or B) into the hooks at the device (SDH-
H).
Use the lifting rod at hydraulic hand pump to pump the
device highly
ATTENTION: Bring hands and feet out of the danger area of
the device (SDH-H)!
Hook C
Spreader bar „large“
Spreader bar „large“
Hook C
Haken A / B
Spreader bar „large“

Operation
12 / 15
5480.0002
V5
GB
The device (SDH-H) can now be driven with the lifted cover carefully to the place of destination.
In order to discharge cover again, rotate by hand the lifting rod at hydraulic hand.
ATTENTION: Bring hands and feet out of the danger area of the device (SDH-H)!
Hook C
Hook A / B
Spreader bar „small“

Maintenance and care
13 / 15
5480.0002
V5
GB
5Maintenance and care
5.1 Maintenance
To ensure the correct function, safety and service life of the device the following points must be executed in
the maintenance interval.
Used only original spare parts, otherwise the warranty expires.
All operations may only be made in closed state of the device!
5.1.1 Mechanical
SERVICE INTERVAL
Maintenance work
First inspection after
25 operating hours
Control and tighten all screws and connections.
(The implementation is only allowed by an expert).
All 50 operating hours
Tighten all screws and connections (take care that the tightening torques according to
the property class of the screws are observed).
Check all existing safety elements (such as linchpins) for perfect function and replace
defective safety elements. 1)
Check all joints, bolts, guidance’s and gears for correct function, if necessary adjust or
replace it.
Check all grippers (if available) for signs of wear.
Grease all slidings (if available) when the device is in opened position with a spatula.
Grease all grease nipples (if available) with a grease gun.
Minimum 1x per year
(at rough conditions shorten the
interval)
Check of all the suspension parts, bolts and straps. Check for corrosion and safety by an
expert.
1)
5.2 Repairs
Only persons with the appropriate knowledge and ability are allowed to repair the device.
Before the device is used again, it has to be checked by an expert.

Maintenance and care
14 / 15
5480.0002
V5
GB
5.3 Safety procedures
It is the contractor’s responsibility to ensure that the device is checked by an expert in periods of
max. 1 year and all recognized errors are removed (see BGR 500).
The corresponding legal regulations and the regulations of the declaration of conformity have to be
observed!
We recommend that after checking the device, the badge “Safety checked” is put on the device.
(Order-No.: 2904.0056+inspection sticker with date).
You can receive these badges from us.
The check by an expert must be proved!
Device
Year
Date
Expert
Company

Maintenance and care
15 / 15
5480.0002
V5
GB
5.4 Hints to the type plate
Type, serial-number and production year are very important for the identification of your device. If you need
information to spare-parts, warranty or other specific details please refer to this information.
The maximum carrying capacity/working load limit (WLL) is the maximum load which can be handled with
the device. Do not exceed this carrying capacity/working load limit (WLL).
If you use the device in combination with other lifting equipment (Crane, chain hoist, forklift truck,
excavator) consider the deadweight of the device.
Example:
5.5 Hints to the renting/leasing of PROBST devices
With every renting/leasing of PROBST devices the original operating instructions must be included
unconditionally (in deviation of the users country's language, the respective translations of the original
operating instructions must be delivered additionally)!

min. 260
max. 956 Hakenabstand
min. Radabstand 351
max. Radstand 1053
1220
max. wheelbase
max. hook distance
min. wheelbase
max. 408
1145
125
min.
122
478
kg /
Product Name:
Eigengewicht / Dead Weight:
Tragfähigkeit / Working Load Limit WLL:
kg /
lbs
lbs
1500
36
3300
79
Hydraulic Manhole Cover Lifter SDH-H15
4
3
C
B
A
B
D
F
7 5
1 3 5 7
F
4
2 6
8
E
D
8 6
C
E
1 2
A
Zust.
Gepr.
Erst.
Name
von
Blatt
Ers. f.
Ers. d.
Urspr.
Artikelnummer/Zeichnungsnummer
Benennung
© all rights reserved conform to ISO 16016
1
16.9.2003
24.1.2003 Kirkamm
Kirkamm
Schachtdeckelheber SDH-H15
D54800002
1
1
Datum

20100006
44800015
21800003
33507479
20000070
44800014
30080004
20000072
21800004
20100006
20100003
44800016
20000069
33507480
20400004
33507481
20000012
20400027
20100004
44800013
20100008
20100006 20100008
30080004
44800011
44800010
44800012 44800009
21600005
20400004
22600080
20020151
20020030
20400050
20400050
4
3
C
B
A
B
D
F
7 5
1 3 5 7
F
4
2 6
8
E
D
8 6
C
E
1 2
A
Zust.
Gepr.
Erst.
Name
von
Blatt
Ers. f.
Ers. d.
Urspr.
Artikelnummer/Zeichnungsnummer
Benennung
© all rights reserved conform to ISO 16016
2
1
25.1.2017
9.7.2002 Kirkamm
R.Wolff
Schachtdeckelheber SDH-H15
E54800002
1
1
Datum

Erstellt/Created:
11.04.2017 / Krasnikov, Igor Zuletzt geändert/Last changed: 11.04.2017 / Krasnikov, Igor
A54800002+0006 SDH-H-15(-UK)
Blatt / Sheet: 1 / 1
Einige der Abbildungen sind möglicherweise optionales Zubehör des Gerätes/Some of pictures may be optional equipment of the device.
29040221
Auf beiden Seiten/
On both sides
29040056
29040665

Proof of maintenance
Warranty claim for this machine only apply for performance of the mandatory maintenance works (by an
authorised specialist workshop)! After each completed performance of a maintenance interval the
included form must be fill out, stamped, signed and send back to us immediately 1).
1) via e-mail to [e-mail] / via fax or post
Operator: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Device type: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Article -No.: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Device-No.: _ _ _ _ _ _ _ _ _ _ _ _
Year of make: _ _ _ _
First inspection after 25 operating hours
Date:
Maintenance work:
Inspection by company:
Company stamp
………………………………………………………………
Name Signature
All 50 operating hours
Date:
Maintenance work:
Inspection by company:
Company stamp
………………………………………………………………
Name Signature
Company stamp
………………………………………………………………
Name Signature
Company stamp
………………………………………………………………
Name Signature
Minimum 1x per year
Date:
Maintenance work:
Inspection by company:
Company stamp
………………………………………………………………
Name Signature
Company stamp
………………………………………………………………
Name Signature