American Dynamics ADCIPE3712OCN User manual

Quick Setup Guide
VideoEdge IP Outdoor Mini-dome
Part Number 8200-2646-07 B0

Quick Setup Guide
3
WARNING
At close range, infrared light can seriously damage a person's vision. Install this
illuminator with a minimum safety zone of 1.22m ( 4 ft. ) between the illuminator and
the closest possible human contact.
Note: 1.22m ( 4 ft. ) is the actual measurement of the strength of the IR Illuminators
that are being used.
Note: CAMERASTARTS UPIN BLACK & WHITE BECAUSE THE IR ILLUMINATOR
IS DISCONNECTED.
For safety reasons, the IR Illuminator is disconnected at the factory. If the IR
Illuminator were to accidentally trigger during install, it may pose a hazard to those
within 4 feet. Once the camera is installed, reconnect the power lead (see
manual). Ensure that you do not cover the photo cell (see manual) after power is
reconnected as that may trigger the IR illuminator.
SERVICE WARNING
DO NOT LOOK DIRECTLY INTO AN OPERATONAL IR ILLUMINATOR.
Since IR light is invisible to the human eye, the only method of verifying a malfunctioning IR
illuminator is to observe the picture at the video output location.
SAFETY PRECAUTIONS
All the following safety and operational instructions to prevent harm or injury to the
operator(s) or other persons should be read carefully before the unit is activated.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied,
reproduced, translated or reduced to any electronic medium or machine-readable
form, in whole or in part, without prior written consent of Tyco International Ltd. ©
Copyright 2009 and its Respective Companies. All Rights Reserved,
American Dynamics
6600 Congress Avenue
Boca Raton, FL 33487, U.S.A.
WARNING
To prevent fire or shock hazard, avoid exposing this unit to rain or moisture.
Do not block ventilation openings.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself, as opening or removing covers may expose
you to dangerous voltage or other hazards. Please refer all servicing to your distributor
/ retailer.
Do not use liquid cleaners or aerosols for cleaning.
To prevent fire or electric shock, do not overload wall outlets or extension cord.
This unit must be grounded to reduce the risk of electric shocks.
The installation should be made by a qualified service person.
PoE considered a Network Environment 0 per IEC TR62101, and thus the
interconnected ITE circuits may be considered SELV.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BYAN INCORRECT TYPE.
DISPOSE OF USED BATTERIESACCORDING TO THE INSTRUCTIONS.

4Quick Setup Guide
1. Name of parts and functions
A. Inner plate mounting holes
B. DC level
C. Reset
D. PC assembly
E. IP module
F. USB plug
G. Side conduct entry
H. Back conduct entry
I. SD card slot
2. Adjusting the camera zoom and focus
1. Loosen the zoom ring thumbscrew.
2. Turn the zoom ring to set the desired zoom.
3. Tighten the zoom ring thumbscrew.
4. Loosen the focus ring thumbscrew.
5. Turn the focus ring to set the desired focus.
6. Tighten the focus ring thumbscrew with the tool to adjust the focus.

Quick Setup Guide
5
3. Camera adjustment
1. Horizontal angle adjustment: turn the platform to adjust the horizontal angle B (90
degrees) and C (180 degrees).
2. Vertical angle adjustment: turn the platform to adjust the vertical angle A (90 degrees).
4. Mounting the housing

6Quick Setup Guide
5. Install, configure and set the IP Dome Camera
The CAMERAdefault setting is DHCP OFF. Users can build the CAMERAworking environment with a static IP
address. The default static IPis192.168.1.168. You can set an IPaddress for the CAMERAif the LAN unit isn’t
connected to a DHCP server. Or turn on to use the DHCP protocol if the DHCP server is working in the LAN,
the CAMERA will obtain an IP address automatically from the DHCP server. The CAMERA is linked by its
Video Out connection via a BNC connector to a monitor's Video In connection. If this connection is there, you
can see some information on the monitor screen, such as the CAMERA factory default Static IP address.
1. Check the IP class of your PC
Step 1: Select Settings from the Start menu, and then click Control Panel.
Step 2: Double-click the Network Connections icon. The Network Connections dialog box appears.
Step 3: Click the Protocols tab in the Network Connections dialog box.
Step 4: Select Internet Protocol (TCP/IP) and click Properties.
Step 5: Select Use the following IP Address to indicate that you do not wish to use DHCP, and assign IP
Address 192.168.1.200 with Subnet mask 255.255.255.0. Click OK when you finish.
Step 6: Choose Close to finish the modification.
2. Install UPnP Packets of your PC
Microsoft Windows XP®does not start the UPnPservice by default. Some packets must be installed before it is
initialized, as described below.
Step 1: Select Set Program Access and Default from the Start menu.
Step 2: Click the Add/Remove Windows Components button when the Add or Remove Programs dialog
box appears.
Step 3: Check the Network Services in the Windows Component Wizard dialog box, and then click Details.
Step 4: Check UPnP User Interface, and choose OK.
Step 5: Click Next when the original Network Component Wizard dialog box returns.After about one minute
the UPnP installation is complete.
Step 6: Select Finish to close.
3. Turn on Services of your PC
After installation, turn on the relative services to start the UPnP protocol. The following procedures will
demonstrate this.
Step 1: Select Settings from the Start menu, and then click Control Panel.
Step 2: Double-click the Administrative Tools icon. The Administrative Tools dialog box appears.
Step 3: Click the Services icon in the Administrative Tools dialog box.
Step 4: Double-click the SSDP Discovery Service icon when the Services dialog box shows up.
Step 5: Choose Automatic in the Startup type, and click OK to start it. The Services dialog box appears
again.
Step 6: Double-click the Universal Plug and Play Device Host icon.
Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it.
Step 8: Restart your system.
4. Set the static IP address in the IP Dome Camera.
Step 1: Plug in the IP Dome camera’s power connection.
Step 2: Plug the USB connector to your PC and the USB socket on the left flank panel. A window pops up
asking if you want to "Run the program", "Open folder to view files", or " Take no action".
Step 3: Choose "Run the program" and click "OK", and the "USB configuration " window will pop up.
Step 4: Set the Network setting and type in the IP address you desire. Before you change the IP address, you
should note the factory default Static IP address ( 192.168.1.168 ).
Step 5: Click the "Apply" button in the "USB Configuration” window. A message pops up asking you to affirm
the action as "OK".
Step 6: Click "OK", and remove the USB connection from the window.
Step 7: Click "Exit" at the bottom of the "USB Configuration” window to close the window. Or, choose the
"Launch" button to see the local camera images directly. Before clicking "Launch", check your PC's IP
address and use the Network connector ( RJ-45 ) to link up with your camera.
Step 8: If you can see the images, then the IP setting is complete.
5. Scan IP Dome Camera through “My Network Place”
After your installation and starting services, the UPnP protocol will take effect.
Step 1: Scan all IP Dome Camera in My Network Place.
Step 2: Double click the IP Dome Camera icon, and the video live stream will pop up automatically without
assigning any IP address in Microsoft Internet Explorer.
6. Change the IP Dome Camera's control and operational settings.
Step 1: Enter the IP address in the IE Browser. You will now see the IP Dome camera images.

Quick Setup Guide
7
Step 2: Use the buttons below the images to enter any other operational settings pages.
Step 3: When you change any setting, please remember to click the "Submit” button in each page.
NOTE: Enable DHCP Function: This function can only work if the LAN, which the unit is connected to,
has a DHCP server. If the DHCP server is working, the IP Dome Camera will obtain an IP address
automatically from the DHCP server.
NOTE: The default "User Name" and "Password" are admin and 9999 respectively. If either the user
name or the password is incorrect, please check the input data and rectify it as necessary.
NOTE: When only one unit of the IP Dome Camera is connected to a computer or LAN, you can freely
assign an IP address for the IP Dome Camera. For example, there is a range of IP Dome Camera IP
addresses from 192.168.1.1 to 192.168.1.255. You can pick one for use from the range of the IP. It’s
not necessary to set MASK and GATEWAY; leave the settings as default.
When an IP Dome Camera is connected to a WAN, you must acquire a unique, permanent IP
address and correctly configure the MASK and GATEWAY settings according to your network
architecture. If you have any questions regarding those settings, please consult a qualified MIS
professional or your ISP.
Specifications
ADCIPE3712OCN VideoEdge IP Outdoor Mini-dome, 3.7-12mm, clear, NTSC, w/PS
ADCIPE3712OCPE VideoEdge IP Outdoor Mini-dome, 3.7-12mm, clear, PAL, EU Plug, w/PS
ADCIPE3712OCPU VideoEdge IP Outdoor Mini-dome, 3.7-12mm, clear, PAL, UK Plug, w/PS
ADCIPE3712OSN VideoEdge IP Outdoor Mini-dome, 3.7-12mm, smoke, NTSC, w/PS
ADCIPE3712OSPE VideoEdge IP Outdoor Mini-dome, 3.7-12mm, smoke, PAL, EU Plug, w/PS
Model
ADCIPE3712OSPU VideoEdge IP Outdoor Mini-dome, 3.7-12mm, smoke, PAL, UK Plug, w/PS
Image device 1/3” Sony Super-HAD CCD
Effective Pixels NTSC:768 x 494, PAL:752 x 582
System NTSC/ PAL
CCD Setting BLC, AGC, AWB, FL / Mirror / Shutter Speed 1/1000
IR wavelength / IR Length 700~1100nm (built-in 850nm) / 25m
Min. Illumination 0.5 Lux @F1.6, 0 Lux IR on
Camera
Lens 3.7~12mm Vari-focal auto iris DC drive lens
Compression MJPEG / MPEG4
Resolution D1/ 2CIF/ CIF
Frame-rate 30 (25) / 24 / 15, 5 fps, adjustable
Picture size (quality) MJPEG: 4~64KB
MPEG4: 64Kbps ~ 8Mbps (Bit-rate)
Image
Motion detection Motion Detection (96 zones, 5 levels)
Interface Ethernet (RJ-45 wired, 10/100 base-tx), MDIX support
Protocols TCP/IP, DHCP, HTTP, ICMP, UPnP, ARP, DNS, DDNS, PPPoE, *FTP,
*SMTP, RTP, RTSP
Network
Throughput 2.0M bytes/sec
Web browser Microsoft IE 6.0 or above
Development tools ActiveX / HTTP-API / SDK
Software Security Multiple level / Multiple users / IP address filtering
Video output 1.0 Vpp, 75 ohm, composite, negative, BNC x 1
Alarm I/O/Reset 1 / 1 / 1
SD card Alarm and Schedule recording / update
USB Mini Type , 1.1 Slave for Configuration / Update
Connectors
Reset Factory Default
Power requirement POE/802.3af class 3, DC 12V/750mA
Power current consumption 700mA IR On, 500mA IR OFF
Operating Temperature 0°C ~ 50°C (32℉~ 122℉)
Dimensions 110mm(High) X 142 mm (Diagram)
Approvals FCC, CE, RoHS
Others
Accessories User manual x 1
*Specifications are subject to change without notice.
**FTP and SMTP functions for PAL version only.