American Dynamics SpeedDome Ultra Manual

SpeedDome®Ultra
Camera Dome
Installation and Service
Manual
8000-1362-01, Rev. B

SpeedDome®Ultra
Camera Dome
Installation and Service Manual
8000-1362-01, Rev. B
MDR 4/97

ii
FCC COMPLIANCE
This equipment has been tested and found to comply with Part 15
of the FCC Rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.
EQUIPMENT MODIFICATION CAUTION
Equipment changes or modifications not expressly approved by
Sensormatic Electronics Corporation, the party responsible for
FCC compliance, could void the user's authority to operate the
equipment.
WARRANTY DISCLAIMER
Sensormatic Electronics Corporation makes no representation or
warranty with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for
any particular purpose. Further, Sensormatic Electronics
Corporation reserves the right to revise this publication and make
changes from time to time in the content hereof without obligation
of Sensormatic Electronics Corporation to notify any person of
such revision or changes.
No part of this manual may be reproduced in any form without
written permission from Sensormatic Electronics Corporation.
SpeedDome is a trademark of Sensormatic Electronics Corpora-
tion. Other product names (if any) mentioned herein may be
trademarks or registered trademarks of other companies.
© Copyright Sensormatic Electronics Corporation 1997

ii
i
TABLE OF CONTENTS
TABLE OF CONTENTSTABLE OF CONTENTS
TABLE OF CONTENTS
Preface .........................................................................................................................vi
Chapter 1 INTRODUCTION .................................................................................................... 1-1
PRODUCT OVERVIEW ............................................................................................ 1-2
Main components................................................................................................ 1-2
Camera options................................................................................................... 1-2
Basic geneology.................................................................................................. 1-2
Indoor mounting methods ................................................................................... 1-4
Hard/Tile ceiling mounting ............................................................................ 1-4
Mounting structures (optional) ...................................................................... 1-4
Outdoor mounting method .................................................................................. 1-6
Features ............................................................................................................. 1-6
Performance features................................................................................... 1-6
Video system dependent features ................................................................ 1-7
Installation and service features ................................................................... 1-8
SPECIFICATIONS..................................................................................................... 1-9
Chapter 2 “INDOOR” INSTALLATION................................................................................. 2-1
BEFORE YOU BEGIN............................................................................................... 2-2
Safety .................................................................................................................. 2-2
Verifying equipment and unpacking.................................................................... 2-2
Tools and equipment required ............................................................................ 2-2
Parts check ......................................................................................................... 2-2
I/O board detachment ......................................................................................... 2-2
INSTALLATION PROCEDURE................................................................................. 2-3
How to use this section ....................................................................................... 2-3
Hard/tile ceiling mounting.................................................................................... 2-3
Hard ceiling surface mounting...................................................................... 2-3
Tile ceiling surface mounting........................................................................ 2-4
Optional mounting structures .............................................................................. 2-5
Top hat housing............................................................................................ 2-5
“Fixed” mounting bracket for hard ceilings or 2x2 ceiling tiles...................... 2-6
“Adjustable” mounting bracket for 2x4 ceiling tiles ....................................... 2-8
Wall mounting bracket................................................................................ 2-10
Wall mounting using a corner bracket........................................................ 2-11
Wall mounting using an arm extension ...................................................... 2-12
Wall mounting using a corner bracket and an arm extension .................... 2-13
Hard ceiling pendent mount........................................................................ 2-14
Electrical box attachment ........................................................................... 2-15
Adapter bracket for indoor SpeedDome housings ..................................... 2-16
Dome setup and attachment............................................................................. 2-17
Skirt and bubble attachment ............................................................................. 2-20
Attaching the skirt to the top hat housing ................................................... 2-20
Attaching the bubble to the top hat housing ............................................... 2-20
Attaching the skirt to the indoor SpeedDome housing ............................... 2-21
Attaching the bubble to the indoor SpeedDome housing ........................... 2-21
Attaching the skirt to the indoor SpeedDome housing ............................... 2-22

iv
Chapter 3 “OUTDOOR” INSTALLATION............................................................................. 3-1
BEFORE YOU BEGIN............................................................................................... 3-2
Safety .................................................................................................................. 3-2
Verifying equipment and unpacking.................................................................... 3-2
Tools and equipment required ............................................................................ 3-2
Parts check ......................................................................................................... 3-2
I/O board detachment ......................................................................................... 3-2
INSTALLATION PROCEDURE................................................................................. 3-3
How to use this section ....................................................................................... 3-3
Mounting the dome’s base to the outdoor SpeedDome housing ........................ 3-4
Dome setup and attachment............................................................................... 3-5
Skirt and bubble attachment ............................................................................... 3-8
Chapter 4 SERVICE ................................................................................................................. 4-1
BEFORE YOU BEGIN............................................................................................... 4-2
Tools and equipment required ............................................................................ 4-2
ROUTINE TROUBLESHOOTING ............................................................................. 4-2
Dome functions but does not pan ....................................................................... 4-3
Dome functions but does not tilt.......................................................................... 4-3
Dome does not “home” or respond to commands (dead dome)......................... 4-3
DETAILED TROUBLESHOOTING............................................................................ 4-5
DOME DISASSEMBLY TECHNIQUES..................................................................... 4-5
How to remove the CPU board ........................................................................... 4-6
How to remove the power supply board.............................................................. 4-6
How to remove the pan motor............................................................................. 4-7
How to remove the slot covers............................................................................ 4-7
How to remove the camera................................................................................. 4-8
How to remove the camera/lens board ............................................................... 4-9
How to remove the tilt motor ............................................................................. 4-10
DOME MAINTENANCE........................................................................................... 4-11
Updating/Reprogramming dome software ........................................................ 4-11
Setting the dome address ................................................................................. 4-11
Changing special features ................................................................................ 4-11

v
Preface
Who should use this manual
Customer Engineers or Dealers who want to install and service
the camera dome.
How this manual is organized
This manual contains the following four sections:
1.0
1.01.0
1.0 INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION provides a product overview and
specifications.
2.0
2.02.0
2.0 “INDOOR”
“INDOOR”“INDOOR”
“INDOOR” INSTALLATION
INSTALLATIONINSTALLATION
INSTALLATION provides procedures
required to mount the dome indoors.
3
33
3.0
.0.0
.0 “OUTDOOR”
“OUTDOOR”“OUTDOOR”
“OUTDOOR” INSTALLATION
INSTALLATIONINSTALLATION
INSTALLATION provides procedures
required to mount the dome outdoors.
4
44
4.0
.0.0
.0 SERVICE
SERVICESERVICE
SERVICE provides troubleshooting and maintenance
information.
Related Documents
Installation and service of this camera dome does not require
detailed knowlege of how it it works or its circuits. However, if
this information is required, order the following document.
Theory for SpeedDome Ultra Camera Domes, document number
8000-1670-01.
Questions?
For technical support on questions that this manual does not
address:
Customer Engineers call: 1-800-543-9740
Dealers call: 1-800-442-2225

vi

CHAPTER 1
SPEEDDOME ULTRA
1-1
SpeedDome Ultra Camera Dome
1INTRODUCTION
nProduct overview ......................................................................1-2
Describes how the dome works, its mounting methods,
major components, and features.
nSpecifications ............................................................................1-9
Lists electrical, environmental, regulatory, and
mechanical specifications for the dome.

INTRODUCTION
SPEEDDOME ULTRA
1-2
PRODUCT OVERVIEW
The SpeedDome Ultra camera dome (Figure 1-1) is part
of a programmable network of camouflaged cameras.
These devices enable security personnel, from a remote
console, to track a target, near or far, even in low light.
Small and unobtrusive, the dome can be used in
facilities such as retail stores, casinos, manufacturing
facilities, hotels, and hospitals, especially where
appearance is important.
Main Components
The dome consists of the following assemblies:
•Base. This assembly mounts directly to an indoor
hard or tile ceiling, or to one of many optional
indoor or outdoor mounting structures. The base has
terminal blocks that receive all video, ac, alarm, and
data connections and has LED indicators that enable
the installer to verify that power and data are
available. The base supplies power and data to the
housing and eyeball assembly, once attached.
•Housing and eyeball assembly. This assembly
“twist locks” onto the base. The housing contains the
dome’s power supply, pan motor, and electronics
used to operate the eyeball. The rotating eyeball,
gloss black and 120mm (4.75") in diameter, contains
a camera, camouflaged lens, tilt motor, and assoc-
iated electronics.
•Camouflaged slot cover (optional). This slot cover
has a 0.5f darker lens that enhances eyeball camou-
flage. It can be used in place of the one on the eye-
ball.
Camera Options
The dome, as shipped, contains one of four different
CCD cameras.
•Color NTSC (60Hz)
•Color PAL (50Hz)
•Monochrome EIA (60Hz)
•Monochrome CCIR (50Hz)
These cameras have 12X optical zoom with continuous
auto focus and backlight compensation. An electronic
zoom provides selectable magnification up to 18X or
48X.
Figure 1-1. SpeedDome Ultra camera dome
Basic Geneology
The dome is available in the four versions listed below.
Basic parts are listed under each version. An exploded
view is shown in Figure 1-2.
•RAS516LP Color NTSC (60Hz)
−0100-1340-01 Base Assy.
−0100-1036-01 Housing and Eyeball Assy.
−0351-1109-01 Install Kit
−0351-1163-01 Slot Cover (optional)
•RAS516LP-1 Color PAL (50Hz)
−0100-1340-01 Base Assy.
−0100-1036-02 Housing and Eyeball Assy.
−0351-1109-01 Install Kit
−0351-1163-01 Slot Cover (optional)
•RAS515LP Monochrome EIA (60Hz)
−0100-1340-01 Base Assy.
−0100-1036-03 Housing and Eyeball Assy.
−0351-1109-01 Install Kit
−0351-1163-01 Slot Cover (optional)
•RAS515LP-1 Monochrome CCIR (50Hz)
−0100-1340-01 Base Assy.
−0100-1036-04 Housing and Eyeball Assy.
−0351-1109-01 Install Kit
−0351-1163-01 Slot Cover (optional)
Base
Housing
and
Eyeball
Assembly

INTRODUCTION
SPEEDDOME ULTRA
1-3
Figure 1-2. Dome components
0400-0833-01 Housing Assy.
0100-1340-01 Base Assy.
Screws (3), M3 x 8 PHP (5801-1051-120)
Slip Ring Assy. (2100-0005-01)
Skirt (0500-6710-01)
Tripod Mount
(0500-6712-01)
Tilt Motor
(3501-0018-01)
Screws, M2x3
(5801-0011-120)
Washer, 1/4 Flat
(2848-8100-07)
0100-1036-00 Housing
and Eyeball Assy.
-01 Color NTSC camera
-02 Color PAL camera
-03 BW EIA camera
-04 BW CCIR camera
0400-0831-00 Eyeball Assy.
-01 Color NTSC camera
-02 Color PAL camera
-03 BW EIA camera
-04 BW CCIR camera
Camera. 1/4 CCD 9Vdc
(2003-0037-01 CLR NTSC)
(2003-0037-02 CLR PAL)
(2003-0037-03 BW EIA)
(2003-0037-04 BW CCIR)
Screw, 1/4-20x3/8
(2802-7407-65)
Bearing Assy., Lens Carriage
(2510-0038-01)
Y
oke Bracket (2)
(0500-7254-01)
Standard Slot Cover with Lens
(0500-6709-01)
(Supplied with Final Assy., not Eyeball Assy.)
0351-1163-01 Install Kit
Optional Slot Cover with 0.5f Darker Lens
(0500-6709-03)
Cable Assy., Tilt
(0650-1680-01)
Slot Cover
(0500-6709-02)
(Supplied with Final Assy., not Eyeball Assy.)
Y
oke
(0500-6709-01)
Camera/Lens Board
(0301-0641-01)
Bearing Assy., Pan Gear
(2510-0040-01)
Housing (0500-7255-01)
Dust Cover
(3100-0066-01)
I/O Board
(0301-0546-01)
Pan Motor (3501-0017-01)
Standoff (3), M3 x 8H x 13L (5899-0055-01)
Screw (4), M3 x 6 (5813-2041-113)
Standoff (3), M3 x 6H x 19L (5887-1122-020)
Power Supply Board (5606-0015-01)
Fan and Cable (0650-1682-01)
Shield (0500-7192-01)
Cap (0500-7256-01)
CPU Board (0301-0578-01)
Ground Clip
(0500-7293-01)
Base
(0500-7257-01)