American Dynamics SpeedDome Ultra II User manual

SpeedDome Ultra II Configuration Utility Quick Reference
8000-1734-01, Rev. C SpeedDome Ultra II Camera Dome Quick Reference
This Quick Reference illustrates the screens found in the
SpeedDome Ultra II Configuration Utility. The large numbers in
the circles represent the number of the screen. The small numbers
appearing to the right of the menu choices represent the screen
you will see if you pick that choice. Note: The numbers in the
circles do not actually appear on the screens.
To start the configuration utility, press and hold Iris Open, press
and hold a Focus button, then press Zoom Out. Refer to the
keyboard or TOUCH TRACKER operating instructions for the
locations of the control buttons.
DOME CONFIGURATION MENU
PAN/TILT/ZOOM OPTIONS
CAMERA & LENS FUNCTIONS
ALARMS / AREAS / HOME
ON-SCREEN TEXT DISPLAY
EXIT AND SAVE CHANGES
QUIT WITHOUT SAVING
RESET TO FACTORY SETTINGS
1
2
3
4
5
NOTE: If password protection is enabled, you must enter the
password before the Dome Configuration Menu will display.
Refer to screen 17 for information.
The following table describes the functions of the controls used
to interact with the screens. Where a specific Focus button is not
listed, either Focus Near or Focus Far may be used.
Function Control
Display configuration menu Iris Open, Focus,
then Zoom Out
Save and exit utility from any screen Iris Close then
Focus
Moves highlight bar up Tilt Up
Moves highlight bar down Tilt Down
Moves highlight bar right Pan Right
Moves highlight bar left Pan Left
Selects the highlighted item Focus Far
Increases the value or displays the next
choice
During naming, moves the cursor to the
right of the current character in the name
Zoom In
(Zoom Tele)
Decreases the value or displays the previous
choice
During naming, moves the cursor to the left
of the current character in the name
Zoom Out
(Zoom Wide)
PAN / TILT / ZOOM OPTIONS
PROPORTIONAL FLIP OFF
1ST ZOOM STOP X 18
MAX TOTAL ZOOM X 96
EXIT
RESET TO FACTORY SETTINGS
2
1
Settings (Defaults in Bold)
Proportional Flip ON / OFF
1st Zoom Stop X 12 / 18
Max Total Zoom X 24/ 36/ 48/ 60/ 72/ 84/ 96
CAMERA & LENS FUNCTIONS
LINE LOCK OFF
AGC MODE ON
AGC GAIN 112
EXIT
RESET TO FACTORY SETTINGS
AUTO WHITE BAL ON
R-B WHITE BAL 457
M-G WHITE BAL 563
3
1
Settings (Defaults in Bold)
Line Lock ON / OFF
AGC Mode ON / OFF
AGC Manual Gain: 0 - 448*
Auto White Bal ON/OFF
R-B White Bal 192-768**
(Low Number: More Blue; High Number: More Red)
M-G White Bal 192-768**
(Low Number: More Green; High Number: More Magenta)
* AGC Mode must be OFF to change
** Auto White Bal must be OFF to change

2Quick Reference
ALARMS / AREAS / HOME
SET ALARM ACTIONS
CONFIGURE NORMAL STATES
CONFIGURE HOME POSITION
EXIT
PROGRAM AREA BOUNDARIES
PROGRAM PRESETS
4
1
6
7
8
9
10
Select an item, then press Focus Far to make the changes.
ON-SCREEN TEXT DISPLAY
STATUS DISPLAY OFF
EXIT
DISABLE ALL NAMES? NO
NAME CONFIGURATION MENU
TEXT ATTRIBUTE OPTIONS
SET PASSWORD
PASSWORD PROTECTION OFF
5
1
12
15
16
Settings (Defaults in Bold)
Status Display ON / OFF
Disable All Names? YES / NO
Password Protection ON / OFF
SET ALARM ACTIONS
EXIT
INPUT NO. ACTION
SEND INPUTS TO HOST YES
NO ACTION
1PRESET 4
2PATTERN 3
3NO ACTION4
INTERNAL ALARMS
6
4
Settings (Defaults in Bold)
Input 1 - 4 Actions NO ACTION / PRESET / PATTERN
Send Inputs to Host? YES / NO
Preset Number 1-4; Pattern Number 1-3
CONFIGURE NORMAL STATES
EXIT
INPUT NO. NORMAL STATE
OPEN
1OPEN
2CLOSED
3OPEN4
7
4
Settings (Defaults in Bold)
Input 1 - 4 Normal State OPEN / CLOSED
CONFIGURE HOME POSITION
EXIT
HOME POSITION PRESET 1
10
RETURN TIME (MINS)
8
4
Settings (Defaults in Bold)
Return to Home Position NO ACTION / PRESET / PATTERN
Return Time (Mins) 1 - 60 (Default is 10 minutes)
PROGRAM AREA BOUNDARIES
ZOOM to mark BOUNDARY
PAN to start of BOUND 3
PAN RIGHT ONLY
FOCUS saves and exits
9
•Up to 16 areas can be programmed.
•Press Zoom In or Zoom Out to set area boundary
•Press Focus Far when finished setting areas
Press Focus
Far twice to
return to 4
If Preset is selected and
no preset exists, you will
see 11

8000-1734-01, Rev. C 3
SELECT PRESET TO PROGRAM
EXIT
PRESET NAME
PRESET
NUMBER PRESET 11
FOCUS FAR to program preset
10
4
•Use Zoom In or Zoom Out choose the correct preset
number.
•Press Focus Far to perform preset programming.
PROGRAM PRESET
PRESET 1
EXIT
Position camera with PAN,
TILT, ZOOM, and IRIS
FOCUS FAR to save and exit
11
This screen appears under two circumstances:
•By selecting a preset number and pressing Focus Far on the
Select Preset To Program screen (see screen 10).
•By selecting a preset that has not been programmed as the
Home Position (see screen 8).
Use Pan, Tilt, Zoom, and Iris controls to set the view for the
preset. Press Focus Far when finished.
NAME CONFIGURATION MENU
EXIT
OFF
CAMERA NAME OFF
AREA NAME OFFPRESET NAME OFFPATTERN NAME ONALARM NAME
FOCUS FAR to program name
12
5
14
13
•Use Zoom In or Zoom Out to change setting for highlighted
item.
•Press Focus Far to perform name programming for
highlighted item. In this example, Camera Naming would be
started.
Settings (Defaults in Bold)
Camera Name ON / OFF
Area Name ON / OFF
Preset Name ON / OFF
Pattern Name ON / OFF
Alarm Name ON / OFF
SELECT NAME TO PROGRAM
EXIT
CURRENT NAME
PATTERN
NUMBER PATTERN 11
FOCUS FAR to program name
13
12
14
Example Select Name to Program Screen (for Patterns)
•Use Zoom In or Zoom Out choose the correct area, preset,
pattern or alarm number.
•Dome moves to start of specified area, preset, or pattern (if
programmed)
•Press Focus Far to display Name Programming Screen
Available Settings:
Area Number 1-16
Preset Number 1-4
Pattern Number 1-3
Alarm Number: 1-4
10 or 4

4Quick Reference
NAME PROGRAMMING
PATTERN 1
NAME: PATTERN 1. . . . . . . . . .
EXIT
UNDO CHANGES AND EXIT
PAN / TILT↔ TABLE; ZOOM ↔ NAME
FOCUS FAR ACCEPTS CHARACTER
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9 ' *
+ - . / : = ?
↔
14
Example Name Programming Screen (for Patterns)
•Names can have up to 19 characters
•Use Zoom In to move cursor one space to right in Name
•Use Zoom Out to move cursor one space to left in Name
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located below the N
TEXT ATTRIBUTE OPTIONS
CHARACTER OUTLINE OFF
EXIT
DIM VIDEO BACKGROUND OFF
15
5
Settings (Defaults in Bold)
Character Outline ON / OFF
Dim Video Background ON / OFF
SET PASSWORD
PASSWORD: * *
CONTINUE
CANCEL
PAN / TILT↔ TABLE; ZOOM ↔ NAME
FOCUS FAR ACCEPTS CHARACTER
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9 ' *
+ - . / : = ?
↔
5
16
•Passwords can be from 1 to 8 characters.
•Asterisks appear when characters are selected.
•Use Zoom In to move cursor one space to right in Password
•Use Zoom Out to move cursor one space to left in
Password
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located below the Ncharacter
•To accept password, move highlight to Continue, then press
Focus Far. Re-enter for Verification appears on screen.
•To cancel password programming, move highlight to
Cancel, then press Focus Far.
•To set or change password, the same password must be
entered twice. After 2nd successful entry, screen 5appears
•Password Protection must be set to ON for password to be
activated. See screen 5.
ENTER PASSWORD
PASSWORD: * *
CONTINUE
CANCEL
PAN / TILT↔ TABLE; ZOOM ↔ NAME
FOCUS FAR ACCEPTS CHARACTER
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9 ' *
+ - . / : = ?
↔
17
•Asterisks appear when characters are selected.
•Use Zoom In to move cursor one space to right in Password
•Use Zoom Out to move cursor one space to left in Password
•Use Pan and Tilt to move highlight around character field
•Press Focus Far to accept highlighted character
•The SPACE character is located below the Ncharacter
•To accept password, move highlight to Continue, then press Focus
Far. If password is correct, screen 1appears. Otherwise, Enter
Password screen remains.
•To cancel, move highlight to Cancel, then press Focus Far.
12 or 13
12 or 13
Blank Space 16 or 5
Blank
Space
1 or 17
Blank
Space