American Dynamics SpeedDome Ultra VII User manual

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
1 of 7
SpeedDome®Ultra VII
22x Dome
Configuration Utility
Quick Reference Guide
If you need assistance…
Contact your Sales Representative.
What is the Dome
Configuration Utility?
The Dome Configuration Utility is used to set features
for your camera dome via a text overlay menu. This
menu is accessed via a keystroke combination on your
camera controller. The utility provides settings relating to
camera functions, alarms, text display, privacy zones,
direction indicators, and password protection. Some
items supplement similar features that may be available
through your controller or switching system.
To start the utility:
1. Select a dome that you need to configure. Refer to
your controller operating instructions for specific
information.
2. Do one of the following:
− If the dome is installed in a SensorNet or RS-422
network, press and hold Iris Open, press and
hold a Focus button, and then press Zoom Out
(Zoom Wide).
− If the dome is installed in a Manchester network,
turn the key switch to Prog (or disable the system
lock on the Touch Tracker), enter 66, then press
Set Preset (Set Shot).
3. The Dome Configuration Menu appears on-screen.
Note: If Password Protection is enabled, Enter
Password (Screen 26) appears first.
© Sensormatic 2003
Choose an option on this screen to change settings.
Table 1 describes the available commands.
IMPORTANT! Commands may differ depending on your
operating environment. These commands apply to
SensorNet, RS-422, and Manchester protocols. For
information about other protocols, refer to the
SpeedDome Ultra VII Configuration Utility Operator’s
Manual (8200-0184-02).
Table 1: SensorNet, RS-422, and Manchester
Commands
If you want to... Use...
Move the Highlight Bar. Pan/Tilt
Select the highlighted item. Focus
Increase value of selected setting, or
display next choice.
Move cursor to right during naming.
Zoom In
(Zoom Tele)
Decrease value of selected setting, or
display previous choice.
Move cursor to left during naming.
Zoom Out
(Zoom Wide)
Save changes and exit from any
screen.
Iris Close,
then Focus
Pan, Tilt, Zoom and
Synchronization Options
PROPORTIONAL FLIP OFF/ON
1ST ZOOM STOP X 33/22
MAX TOTAL ZOOM X 44...242
LINE LOCK ON/OFF
FREEZE FRAME OFF/ON
I/F RETURN TO AUTO OFF/ON/
IRIS/FOCUS
• The default 1st Zoom Stop setting is 33X.
• The default Max Total Zoom setting is 88X.
• Maximum total zoom settings are:
44X, 66X, 88X, 110X, 132X, 154X, 176X, 198X,
220X, and 242X.
• The default Line Lock setting is ON.
• The default Freeze Frame setting is OFF.
• The default I/F Return to Auto is ON.
1
2

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
2 of 7
Camera Functions
CAMERA FUNCTIONS
Auto White Bal OFF/ON
W Bal Adj: Red 0-511 Blue 0-511
AGC/Shutter Max Gain Limit
Open Shutter(NTSC)0-28 dB 1/2-1/60 s
RESET TO FACTORY SETTINGS
EXIT
Open Shutter(PAL) 0-28 dB 1/3-1/50 s
Some settings appear only when the associated setting
is active. Use the following information to identify which
settings apply.
Auto White Balance and
Red/Blue Values
The Auto White Bal setting determines if the Red and
Blue values can be changed.
Auto White Bal Red Blue
ON N/A N/A
OFF Yes Yes
AGC/Shutter Settings
The AGC/Shutter setting determines if the Max Gain
and Limit settings apply.
AGC/Shutter Max Gain Limit
Open Shutter Yes Yes
AGC ON Yes N/A
AGC OFF N/A N/A
Alarms, Areas, Home,
Presets and Privacy Zones
ALARMS/AREAS/HOME/PRESETS/PZ
SET ALARM ACTIONS
SET ALARM STATES
SET HOME POSITION
SET NORTH POSITION
AREA BOUNDARIES
PRIVACY ZONES
PRESETS
SCAN LIMITS
EXIT
This screen provides links to lower level screens. See
the following screens:
• Set Alarm Actions (Screen 8)
• Set Alarm States (Screen 9)
• Set Home Position (Screen 10)
• Set North Position (Screen 11)
• Area Boundaries (Screen 12)
• Privacy Zones (Screen 13)
• Select Preset to Program (Screen 17)
• Scan Limits (Screen 19)
On-Screen Text Display
ON-SCREEN TEXT DISPLAY
STATUS DISPLAY ON/OFF
DISABLE ALL NAMES? YES/NO
DIAGNOSTIC DISPLAY ON/OFF
DIRECTION INDICATOR ON/OFF
NAME CONFIGURATION MENU
TEXT ATTRIBUTE OPTIONS
EXIT
In addition to the settings available, this screen provides
links to lower level screens. See also:
• Name Configuration Menu (Screen 20)
• Text Attribute Options (Screen 23)
3 4
5

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
3 of 7
Language and Password
LANGUAGE / PASSWORD
LANGUAGE SELECTION
SET PASSWORD
PASSWORD PROTECTION OFF
EXIT
/ON
In addition to enabling password protection, this screen
provides links to lower level screens. See the following
screens:
• Language Selection (Screen 24)
• Set Password (Screen 25)
Dome Information
DOME INFORMATION
NAME: SpeedDome Ultra VII
Mnemonic: SDU 7
Software Ver: 0710-0147-0100
Device Type: 24770105
SN: 01234567890123456789
Manufacture Date: 11012002
Dome Statistics
EXIT
Select Dome Statistics (Screen 27) to display dome
usage information.
Set Alarm Actions
SET ALARM ACTIONS
INTERNAL ALARMS
INPUT NO. ACTION
1 NO ACTION
2 PRESET 1-96
3 PATTERN 1-3
4 NO ACTION
SEND INPUTS TO HOST? YES / NO
EXIT
No Action is the default setting for all inputs. Preset 1-
96 or Pattern 1-3 may be assigned as the alarm action.
Set Alarm States
SET ALARM STATES
INPUT NO. NORMAL STATE
1 OPEN / CLOSED
2 OPEN / CLOSED
3 OPEN / CLOSED
4 OPEN / CLOSED
EXIT
Open is the default setting for all inputs.
Set Home Position
SET HOME POSITION
HOME POSITION NO ACTION
RETURN TIME MINS 1-60 (10)
EXIT
PRESET 1-96
PATTERN 1-3
No Action is the default setting for the home position.
Preset 1-96 or Pattern1-3 may be assigned to the home
position.
Set North Position
SET NORTH POSITION
PAN to new north position
ZOOM to mark north position
FOCUS quits w/o changing
The default North Position is 0-degrees Pan/Tilt.
7
8
9
10
11
6

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
4 of 7
Area Boundaries
A
REA BOUNDARIES
PAN to start of BOUND 1-16
PAN RIGHT ONLY
ZOOM to mark BOUNDARY
FOCUS saves and exits
Up to 16 areas may be programmed. These areas are
separate from areas that may be available through your
switcher.
Privacy Zones
PRIVACY ZONES
A
DD PRIVACY ZONES
DELETE SPECIFIC ZONE
DELETE ALL ZONES
HIDE ALL ZONES? NO/YES
EXIT
In addition to hiding all programmed privacy zones, this
screen provides links to lower level screens. See the
following screens:
• Add Privacy Zones (Screen 14)
• Delete Privacy Zone (Screen 15)
• Delete All Zones (Screen 16)
Add Privacy Zones
NEW PRIVACY ZONE
Navigate to corner 1(2, 3)
ZOOM to Mark Corner
FOCUS to Abandon Zone
• Up to 8 Privacy Zones may be programmed.
• Three points must be selected to establish the
Privacy Zone. The fourth point is automatically
calculated.
• Use the Pan/Tilt control to position the arrows over
the selection point. If arrows blink, this is not a valid
selection area.
• Press Zoom to save the point.
Delete Privacy Zone
Navigate to zone
ZOOM to delete zone
FOCUS quits w/o changing
• Arrows must be clearly positioned in zone to delete.
• Use the Pan/Tilt control to position the arrows over
the zone. If arrows blink, this is not a valid selection
area.
• Press Zoom to delete the selected zone.
12
13
14
15

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
5 of 7
Delete All Zones
YOU ARE ABOUT TO DELETE
ALL PRIVACY ZONES.
CANCEL
CONTINUE
This option permanently removes all programmed
Privacy Zones. To temporarily hide the zones, use Hide
All Zones. See Privacy Zones (Screen 13).
Select Preset to Program
SELECT PRESET TO PROGRAM
PRESET
NUMBER PRESET NAME
1-96 PRESET 1-96
FOCUS FAR to program preset
EXIT
The number of presets available depends on your
operating environment.
• If installed under SensorNet or RS-422, up to 96
presets are available.
• If installed under Manchester, up to 64 presets are
available.
Program Preset
PRESETS
PRESET X
Position camera with PAN
TILT, ZOOM and IRIS
FOCUS FAR to save and exit
EXIT
This screen also appears if a Preset is selected for the
Home Position (Screen 10), and the selected preset
has not been programmed.
Scan Limits
SCAN LIMITS
PAN to LEFT limit
ZOOM to mark BOUNDARY
Cancel RIGHT limit to Delete
CANCEL
SCAN LIMITS
PAN right to RIGHT limit
ZOOM to mark BOUNDARY
Cancel RIGHT limit to Delete
CANCEL
Scan Limits are used to set right and left areas of
surveillance with compatible controllers. These scans
may be activated using the Quick Set Menu
(Screen 28).
• Use Pan/Tilt to adjust the dome’s pointing direction.
• Press Zoom to select the left and right scan limits.
• Press Focus to cancel changes.
• Press Focus when setting right scan limit to delete
the scan limits.
Name Configuration Menu
NAME CONFIGURATION MENU
CAMERA NAME ON/OFF
AREA NAME ON/OFF
PRESET NAME ON/OFF
PATTERN NAME ON/OFF
ALARM NAME OFF/ON
FOCUS FAR to program names
RESET PROGRAMMABLE NAMES
EXIT
• Use Zoom to change the display setting.
• Press Focus to start name programming for
highlighted setting.
• If Camera is selected, the Name Programming
(Screen 22) automatically appears. For others,
Select Name to Program (Screen 21) appears.
16
17
18
20
19

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
6 of 7
Select Name to Program
SELECT NAME TO PROGRAM
PRESET
NUMBER CURRENT NAME
1-96 Preset 1-96
EXIT
FOCUS FAR to program names
/PATTERN/AREA/ALARM
1-3 Pattern 1-3
1-16 Area 1-16
1-4 Alarm 1-4
• Use Zoom to select the appropriate Alarm, Area,
Pattern, or Preset number.
• Press Focus to start name programming.
Name Programming
NAME PROGRAMMING
CAMERA
NAME: CAMERA.............
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz 0123456
789/-
UNDO CHANGES AND QUIT
EXIT
/PRESET/PATTERN/AREA/ALARM
• Names may contain up to 18 characters.
• Use Pan/Tilt to move the highlight around available
character field. Press Focus to select highlighted
character.
• Zoom In moves the highlight one space right in the
name; Zoom Out moves the highlight one space left.
Text Attribute Options
TEXT ATTRIBUTE OPTIONS
CHARACTER OUTLINE ON/OFF
TRANSLUCENT NAMES ON/OFF
EXIT
If Privacy Zones are displayed, Translucent Names is
automatically disabled.
Language Selection
LANGUAGE SELECTION
ENGLISH
SPANISH
FRENCH
GERMAN
ITALIAN
PORTUGUESE
EXIT
• Dome must reset for language setting to change.
• Programmed names do not change after setting the
language. Only default names change.
Set Password
SET PASSWORD
PASSWORD: ********
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz 0123456
789/-
CONTINUE
CANCEL
• Passwords may contain up to 8 characters.
• See Name Programming (Screen 22) for operating
instructions.
Enter Password
ENTER PASSWORD
PASSWORD: ********
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz 0123456
789/-
CONTINUE
CANCEL
• This screen only appears when Password
Protection is enabled. The password must be
successfully entered before the Dome Configuration
Menu will appear.
• See Name Programming (Screen 22) for operating
instructions.
21
22
23
24
25
26

SPEEDDOME ULTRA VII 22X DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE (8200-0184-03, REV. C)
7 of 7
Dome Statistics
DOME STATISTICS
PanStat TiltStat ZoomStat
R 000000C9 00000085 00000011
L 0000006A 00000074 00000012
M 000001B5 00000089 00000048
T 00000013 00000017 0000000E
Pwr/Run Pwr/Run
O 00007615 W 00000000
P 00000000 U 00000000
EXIT
This screen displays operating statistics for the dome.
The information displayed represents the number of
occurrences or time in seconds (displayed in
hexadecimal format).
• Rrepresents time moving Right in seconds.
• Lrepresents time moving Left in seconds.
• M represents Total Move Time in seconds.
• Trepresents Target Count.
• O represents Operating Time in seconds.
• P represents Power Failure Reset Count.
• Wrepresents Watchdog Reset Count.
• Urepresents User Reset Count.
Quick Set Menu
0 TOGGLE QUICK SET MENU
1 DOME CONFIG MENU
2 AUTO IRIS/AUTO FOCUS
3 FLIP
4 PEEL PATTERN
15 SMOOTH SCAN
16 STEPPED SCAN
17 RANDOM SCAN
20 DOME INFORMATION
The Quick Set Menu provides easy access to dome
features and menus with compatible controllers.
• Press the Quick Set button (varies by controller) to
display the menu.
• Enter a number and press the Quick Set button to
activate the setting or menu.
• Enter 0and press the Quick Set button to close the
menu.
Refer to your controller instructions to determine if it is
compatible with the Quick Set Menu function.
27 28
www.americandynamics.net