American legend Ht600 User manual

888-996-2729-1

1353-378-668-1:XAF

moc.stropsedalacse@gameroom

ytilauqtsehgihehtfoerastcudorpruotahterusneotevirtseW

fi,revewoH.strapgnissimrostcefedgnirutcafunamfoe

erfdna

,tcudorpwenruoyhtiwsmelborpynaevahuoy

EROTSEHTOTTINRUTERTONOD ,

:@eerfllotsutcatnocesaelp

:otetirwrO

stropSedalacsE

tnemtrapeDecivreSremotsuC

988xoB.O.P

60774NI,ellivsnavE

date code (if,rebmunledomruoyedivorpesaelpstropSedalacsEgnitcatnocnehW

erasrebmunesehT.traptnemecalp

eragnitseuqerfirebmuntrapdna,)elbacilppa

.launamsrenwosihtnidna,gnigakcap,tcudorpehtnodetacol

rebmuNledoMruoY

.straptuobagniriuqninehwdate coderuoyevahesaelP

HT600

888-996-2729-1llaCecivreSremotsuCroF1stropSedalacsE1402©

Date Code: 2 - HT600 - - MW

Purchase Date:

PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Make sure you understand the following tips before you begin to assemble your hockey table.

1. Start all bolts by hand before tightening.

2. Some drawings or images in this manual may not look exactly like your product. Please

read and understand the text before starting each assembly step.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

THIS HT600 PHAZER 7.5 FT AIR HOCKEY TABLE

Assembly Tips

Tools Required:

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO

ADULTS ARE NEEDED TO PUT THIS HOCKEY TABLE

TOGETHER.

T1 - Allen Wrench (Included) and T2 - Wrench (Included)

IMPORTANT! READ EACH STEP

IN THIS MANUAL BEFORE YOU

BEGIN THE ASSEMBLY.

Phillips Screwdriver

Furniture Polish and Cloth

4 mm x 18 mm

Phillips Round

Head Screw

H1 = 24 pcs H2 = 24 pcs H3 = 16 pcs

1/4” x 16 mm 4 mm x 50 mm

WARNING:

CHOKING HAZARD

Small parts.

Not for children under

3 yrs.

1/4” x 28 mm

Allen Head Bolt Phillips Round

Head Screw

Flat Washer

H4 = 12 pcs H5 = 36 pcs

5/16” x 19mm

5/16” x 38 mm

Allen Head Bolt Flat Washer

H6 = 12 pcs

5/16” Lock Washer

H7 = 12 pcs

5/16” Hex Nut

H8 = 2 pcs

3/16” x 25 mm

Allen Head Bolt

H9 = 96 pcs

4 mm x 12 mm

Phillips Round

Head Screw

H10 = 54 pcs

4 mm x 44 mm

Phillips Flat

Head Screw

H11 = 24 pcs

H12 = 12 pcs

5/16” x 44 mm

Allen Head Bolt

4 mm x 15 mm

Phillips Round

Head Screw

H13 = 4 pcs

Allen Wrench

T1 = 1 pc

Striker

T2 = 1 pc

12mm Wrench

A1 = 4 pcs

Puck

A2 = 4 pcs

Felt Pad

A3 = 4 pcs

NOTE: A3 Felt Pads may already

be attached to A1 Strikers.

Side Apron with

ON/OFF slot

P1 = 1 pc P2 = 4 pcs P3 = 4 pcs

Left Leg Panel Right Leg Panel

WARNING:

CHOKING HAZARD

Small parts.

Not for children under

3 yrs.

Air Hockey Cabinet

P5 = 4 pcs P6 = 4 pcs

Leg Bottom Board

Back Leg Panel

P7 = 2 pcs

End Leg Panel

P8 = 2 pcs

End Apron

P9 = 1 pc

Side Apron

P10 = 1 pc

U - Plastic Bracket

P11 = 12 pcs

L - Plastic Bracket

P12 = 12 pcs

P13 = 4 pcs

Corner Post Leg Leveler

P15 = 4 pcs

P4 = 4 pcs

Front Leg Panel

P14 = 8 pcs

Leg Panel

Connecting Plate

Puck Catcher

P16 = 2 pcs

Hole Trim

NOTE: P7 End Leg Panels are

packed under the table cabinet.

P17 = 1 pc P18 = 2 pcs P19 = 1 pc

Lower Puck Catcher A/C Adapter

WARNING:

CHOKING HAZARD

Small parts.

Not for children under

3 yrs.

Scorer Console

P23 = 1 pc

P21 = 1 pc

Metal Bracket Junction Box

P22 = 2 pcs

Upper Puck Catcher

P24 = 2 pcs

Lighting LED Rail

P20 = 1 pc

ON/OFF Switch

with Sensor Wires

LED

HOME

VISITOR

CONTROL

DC 5V

350mA

(Factory Installed) (Factory Installed)

888-996-2729-1llaCecivreSremotsuCroF6stropSedalacsE1402©

STEP 1:

Leave P1 Air Hockey Table Cabinet face down in carton to assemble.

Install four pieces P11 U-Plastic Bracket onto two pieces P8 End Apron, one piece P9 Side Apron and

one piece P10 Side Apron with ON/OFF Slot using U-Guides with four pieces H9 Screws as shown in

FIGURE 1 and DETAIL A.

IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H9 SCREWS.

PARTS REQUIRED:

48 pcs - H9 Phillips Round Head Screw 1 pc - P10 Side Apron with

2 pcs - P8 End Apron ON/OFF Slot

1 pc - P9 Side Apron 12 pcs - P11 U-Plastic Bracket

FIGURE 1

P10

U-Guide

P11

U-Guide

P11

DETAIL A

Note: Some parts are packed on under side of Hockey Table Main Cabinet , please carefully remove these

parts before starting this assembly.

888-996-2729-1llaCecivreSremotsuCroF7stropSedalacsE1402©

STEP 2:

Leave P1 Air Hockey Table Cabinet face down in carton to assemble.

Install P8 End Aprons and P9 / P10 Side Aprons from assembly STEP 1 using H4 Allen Head Bolts,

H5 Flat Washers, H6 Lock Nuts and H7 Hex Nuts as shown in FIGURE 2 and DETAIL B.

IMPORTANT NOTE: DO NOT TIGHTEN H4 BOLTS ON THIS STEP.

IMPORTANT NOTE: P10 SIDE APRON WITH ON/OFF SLOT MUST CLOSE TO P23 JUNCTION

BOX AS SHOWN IN FIGURE 2.

PARTS REQUIRED:

12 pcs - H4 Allen Head Bolt 1 pc - P1 Air Hockey Table Cabinet

24 pcs - H5 Flat Washer 1 pc - T1 Allen Wrench

12 pcs - H6 Lock Washer 1 pc - T2 12mm Wrench

12 pcs - H7 Hex Nut

DETAIL B

FIGURE 2

P10

H5 H6 H7

P1 Air Hockey Table

Cabinet Support Brace

IMPORTANT NOTE:

P10 Side Apron with

ON/OFF Slot must

close to P23 Junction

Box as shown.

P23

STEP 3:

Slide P13 Corner Posts to each end of Side Apron and End Apron as shown in FIGURE 3.

IMPORTANT NOTE: SLIDE P13 CORNER POSTS WITH ARROW POINTING DOWN.

TIGHTEN ALL H4 BOLTS ON THIS TIME.

PARTS REQUIRED:

4 pcs - P13 Corner Post

FIGURE 3

NOTE: Install P13 Corner Posts

with arrow pointing down.

P13

STEP 4:

With the help of another adult, Install P12 L-Plastic Brackets onto P1 Air Hockey Table Cabinet,

P8 End Aprons and P9 / P10 Side Aprons using H9 Phillips Round Head Screws as shown in

FIGURE 4 and DETAIL C.

IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H9 SCREWS.

PARTS REQUIRED:

48 pcs - H9 Phillips Round Head Screw

12 pcs - P12 L-Plastic Bracket

FIGURE 4

DETAIL C

P1 Air Hockey

Table Cabinet

1 2

P8 End Aprons,

P9 / P10 Side

Aprons

P1 Air Hockey Table Cabinet

Underneath of Playfield.

Aprons

NOTE: Angle

surface

on this side. H9

P12

P12 H9

STEP 5:

Secure P13 Corner Posts using H10 Screws as shown in FIGURE 5.

Install P16 Puck Catcher Hole Trims using pre-drilled holes with H13 Screws as shown in FIGURE 5.

Install P22 Upper Puck Catchers using pre-drilled holes with H10 Screws as shown in FIGURE 5.

Install P18 Lower Puck Catchers with Sensor Wires using pre-drilled holes with H10 Screws as

shown in FIGURE 5.

IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H10 AND H13 SCREWS.

Next, feed the sensor plugs from P18 through underneath support beams and connect to P23 Junction

Box (factory installed) as shown in DETAIL D.

PARTS REQUIRED:

18 pcs - H10 Phillips Round Head Screw 2 pcs - P16 Puck Catcher Hole Trim

4 pcs - H13 Phillips Round Head Screw 2 pcs - P18 Lower Puck Catcher with Sensor Wires

2 pcs - P22 Upper Puck Catcher

FIGURE 5

H10

P13

P22

P16

H13

H10

P18

H10

P23

CONTROL HOME LED

VISITOR LED

DETAIL D

P18

Sensor

Wire

P18

Sensor

Wire

DC 5V

350mA

Table of contents

Other American Legend Video Gaming Accessories manuals

American Legend

American Legend 45-1800W/F User manual

American Legend

American Legend AL6069F User manual

American Legend

American Legend AL2100W User manual

American Legend HT600 User manual

Popular Video Gaming Accessories manuals by other brands