American sensor Sa360 User manual

SMOKE ALARM MANUAL

Ionization Type Model - 120 VAC Hardwire

€Model SA360 - Professional Multi-Location Model 120 Volt

A C Hardwire Smoke A larm. T his model is interconnectable with

upto 11 other units.

Important information about your smoke alarm

€ Install alarms outside of every bedroom area and on every floor of

your home. Please refer to Section 3 •W here to Locate Smoke

AlarmsŽfor details.

€ Test the alarm weekly by pressingand holdingthetest button for

up to 20 seconds until the alarm sounds.

€

T he model described in this manual is designed for single

family residences, including homes and apartments rather than

commercial or industrial use.

Smoke Alarm Safety Features

€ Dual-Ionization Chambers - A dvanced design responds to visible

or invisible particles of combustion (smoke) to sense fires in their

earliest stages. C ompensates for changes in humidity and

temperature to virtually eliminate •nuisanceŽalarms caused by

normal atmospheric changes in the home.

€OperatingLight (LED) - A continuous green light located behind

the slotted case indicates the smoke alarm is receiving AC power.

€ Interconnection - Interconnection facilities for up to 11 other

units, using only three wires, including AC power. W hen one

alarm sounds, all properly interconnected smoke alarms follow.

NOT E: Interconnect only with the models specified in Section 6.

€ Alarm Source Indicator - T he red operating light in the unit

originatingthealarmwill flash rapidly in the event of an alarm.

With interconnected units, this featureallows for an easy check to

determine the originator.

€Locking Key - T he auxiliary locking key provided can be used to

lock the smoke alarm to the mounting plate. T his helps to reduce

the risk of unauthorized removal.

€ Sensitivity Test Button - Test sensitivity, as well as circuitry and

horn. With interconnectedunits, activatingtest button on one

unit will cause all properly interconnected units to sound. A n

important and convenient check of system integrity.

€ Quick Disconnect Power Connector - For easy installation,

connect the wires separately from the unit and then pluginto the

back of the unit.

€ Detachable Mounting Plate - For easily securing the alarm to the

junction box.

CONTENTS OF THIS MANUAL

1. CA PABILIT IES AND LIMITATIONS OF SMOKE ALA RMS

2. SA FETY TIPS

3. WHERE TO LOCATE SMOKE ALARMS

4. NFPA RECOMMENDATIONS

5. LOCATIONS TO AVOID

6. INSTALLATION AND TEST ING

7. MAINTENANCE AND TROUBLESHOOT ING

8. LIMIT ED WARRANTY

9. OTHER AMERICAN SENSORS PRODUCTS

1. CAPABILITIES AND LIMITATIONS OF SMOKE ALARMS

A merican Sensors smoke alarms are designed to provide early

warning of fire and smoke at reasonable cost. Early warning can

mean the difference between a safe escape and no escape at all.

While smoke alarms can provide invaluable protection for you and

your family, they do have limitations.

€ Smoke alarms cannot work without power. Battery operated

alarms will not work without proper batteries, with dead batteries

or if batteries are not properly installed. A C powered alarms will

not work if their AC power supply iscut off by an electrical fire,

an open fuse, a circuit breaker or any other reason.

If you are concerned about the reliability of either batteries or your

AC power supply for any of theabovereasons, youshouldinstall

in your home both A C and battery powered smoke alarms for

added security. A merican Sensors also offers the SA 379 model

which is A C powered with battery back-up.

€ Smoke alarms are incapable of soundingthe alarm until smoke

reaches the sensing chamber. A nythingpreventing smoke from

reaching the alarm may delay or prevent an alarm. A smoke alarm

cannot detect fire in the walls, chimney or roof unless and until a

significant amount of smoke reaches the alarm. A closed door may

prevent smoke from reaching an alarm on the other side of the

door. A smoke alarm may not sense a fire on another floor of a

home. For example, a basement smoke alarmmay not detect a fire

which started on the first or second floor.

€ Smoke alarms may not be heard. T he loudness of the horn in

your alarmmeetscurrent standards. However, the sound maybe

blocked by distance, closed doors, or ambient noise such as traffic

or a stereo. Smoke alarms may not be heard by persons who are

hardof hearing.

For these reasons, a smoke alarm should be installed in every

room or at least on every level of your home. American Sensors

recommends that hardwire A C Powered smoke alarms be

interconnected, so that onealarmwill trigger all other alarms to

soundtheir alarms.

€ Smoke alarms are not fool-proof. Smoke alarms may not always

sense every kind of fire. T hey cannot be expected to sense fires

caused by carelessness or by safety hazards. T hey may not give

early warning of fast growing fires caused by smoking in bed,

violent explosions, escaping gas, improper storage of flammable

materials, overloaded electrical circuits, natural causes such as

lightning, children playingwith matches, or arson.

€ Smokealarms are not substitutes for property, disability, life or

other insurance of any kind. Home owners and renters should

continue to insure their lives and property. Consult your insurance

agent.

€ Smoke alarms have limited lives. One or more of the many

componentscouldfail at anytime. Therefore, test your smoke

alarmweekly. Clean and takecareof it asdescribed in this

manual. Repair or replacethe smokealarmwhen it fails totest

properly. Your smoke alarm should be replaced if it is ten years

old.

€

A photoelectronic smoke alarm senses smoke using an electronic

photo receptor to sense the scattering of light by smoke particles.

2. SAFETY TIPS

Properly installed and maintained smoke alarms are an essential part

of a goodhome fire safety program. Your fire safety program should

also include a review of fire hazards and the elimination of

dangerous conditions whenever possible. Consider the following tips:

€ Use smoking materials properly. N ever smoke in bed.

€ Keep matches and cigarette lighters away from children.

€ Store flammable materials in proper containers. N ever use them

near an open flame or sparks.

€ Keep electrical appliances in good condition. Do not overload

electrical circuits.

€ Keep stoves, fireplaces, chimneys, and barbecue grills grease free.

Make sure they are properly installed and away from any

combustible materials.

€ Keep portable heaters and open flames such as candles away from

combustible material.

€ Do not allow rubbish to accumulate.

€ Keep a supply of extra batteries on hand for your battery powered

smoke alarms.

€ Do not stand too close to the alarm when the unit is in alarm as the

loud horn could damage your hearing.

Never disconnect the battery or the A C power on any type of smoke

alarm to silence a nuisance alarm. C lear the area of smoke by opening

doors and windows or fanning the smoke away.

Most important, when fire strikes, a prepared

and practicedescape plan can make the difference between life and

death. Develop an escape plan and practice it with the entire family,

includingsmall children.

€ Ensure all family members are familiarized with the alarm signal.

€ Prepare an escape plan. DrawaFloor Plan of Your Home and

determine two exits from each room. T here should be a way to get

out of each bedroom without openingthe door.

€ Have Fire Drills Often. Practice your Escape and BE PREPA RED.

€ Decide on a meeting place at a safe distance from your home.

IN CASE OF FIRE

€ Don•t waste time collecting possessions after a fire starts.

€ A rouse all occupants and leave the building. Your most valuable

possession is your life.

€ Doors can mean escape or death. Never open doors without first

checking for heat. Test them with your hands, if they feel warm, fire

may be walled up behind them - leave closed and find another

escape route.

€ Call the fire department from OU TSIDE the building.

€ If trapped inside, stay close to the floor, cover mouth with cloth,

conserve breath as you crawl to safety.

€ Keep all doors and windows closed except for escape purposes.

€ NEV ER re-enter a burning building.

€ Keep your family in a pre-arranged meeting place after your escape.

Your local fire department may be able to offer you additional ideas

for safety and escape plans in the home.

3a. WHERE TO LOCATE SMOKE ALARMS

As a minimum, smoke alarms should be located between sleeping

areas and potential sources of fire such as a kitchen, heated garage or

basement. I n single storey homes with one sleepingarea, an alarm

should be installed in the hallway outside the bedrooms (see Figure

1). In single storey homes with two separate sleeping areas, a

minimum of two alarms are required, one outside each sleeping area

(see Figure 2). In multi-level or split-level homes, asa minimum, an

alarm should be installed outside each sleeping area, in the basement

and at every level of the home (see Figure 3).

€ In every room of your home (except the bathroom): Research

indicates that substantial increases in warning time can be obtained

with each properly installed, additional alarm.

€ In bedrooms: In anticipation of firesoriginatingwithin these rooms,

caused by faulty wiring, lamps, appliances, smokingor other hazards.

€ In hallways: A t adistance no greater than 13 feet (4 meters) from

the farthest wall and no greater than 26 feet (8 meters) from the

next alarm.

€ In the center of a room or hallway: A s it is impossible to predict the

source of a fire. If it is necessary to place the alarm on a wall, always

locate the top of the smoke alarm 4-6 inches (10-15 cm) from the

ceiling.

€ A s needed: To compensate for closed doors and other obstacles that

may interferewith thepath of smoke toan alarm. They may also

prevent occupants on one side of a closed door from hearing a alarm

on the other side of the door.

€ Model SA360 - Professional Multi-Location model can belocated

in any area of the home.

READ •CAPABILITIES AND LIMITATIONS OF SMOKE

ALA RMSŽin Section 1of thismanual.

Your local fire department or insurancecompany may beable togive

you further advice on the best smoke alarm locations in your home.

Call them and ask.

T here are two different types of smoke alarm technology

currently in general use: ionization and photoelectronic. While

both types of technology are suitable for general residential use,

an ionization alarm will normally respond faster to fast flaming

fires, while a photoelectronic alarm may be more sensitive to

detecting slow smoldering fires. Because home fires develop in

different ways and are often unpredictable in their growth, it is

impossible topredict which type of alarm will providetheearliest

warning. For best home protection install at least one

photoelectronic and one ionization smoke alarm on each level of

your home. Model SA 360 is an ionization typesmoke alarm.

Ionization Technology vs.

Photoelectronic Technology

Smoke A larms

3b. WHERE TO LOCATE SMOKE ALARMS IN MOBILE HOMES

N OT E: Power supply must be 120 Volts AC for model SA 360.

In mobile homes built after 1978 locate the smoke alarm as

described above.

Older mobile homes may have little or no insulation compared to

the ones built post 1978. T hese uninsulated exteriors can disrupt

airflowaround the smoke alarmin hotter or colder weather. Locate

the alarm only on interior walls 4Ž to 6Ž(10 to 15 cm) from ceiling

1. if you own an older mobile home or 2. if you notice theexterior

walls and/or ceiling are noticeably cold or warm or 3. if you are

uncertain about the quality of insulation.

Regardless of the age of the mobile home, locate alarms throughout

to ensure maximum protection. Follow the location instructions in

this manual.

4. NFPA RECOMMENDATIONS

For your information, the N ational Fire Protection Association•s

Standard 72 reads as follows:

2-2.1.1.1

Smoke alarms shall be installed outside of each separate sleeping

area in the immediate vicinity of the bedrooms and on each

additional storey of the family living unit, including basements and

excluding crawl spaces and unfinished attics. In new construction a

smoke alarm also shall be installed in each sleeping room.

A-2.5.2.1 Smoke Detection- A reMore Smoke AlarmsDesirable?T he

requirednumber of smoke alarms might not provide reliable early

warningprotection for those areas separated by a door from the

areas protected by therequiredsmoke alarms. For this reason, it is

recommended that the householder consider the use of additional

smoke alarms for those areas for increased protection. The

additional areasincludethebasement, bedrooms, diningroom,

furnace room, utility room, and hallways not protected by the

requiredsmokealarms. Theinstallation of smoke alarmsin

kitchens, attics(finishedor unfinished), or garages isnot

normally recommended, as these locationsoccasionally

experience conditions that can result in improper operation.

5. LOCATIONS TOAVOID

Avoid locations where smoke may not reach the alarm in timeto

provide early warning, or where the alarm may not be effective.

DO NOT PLACE SMOKE ALAR MS:

€ In turbulent air from fans, doors, windows, etc. Therapidair

movement may prevent combustion particles from entering the

alarm.

€ I n dead air spaces such as at the peak of an •A Žframe ceiling.

•Dead airŽ at the top may prevent smoke from reaching the alarm

in time to provide early warning. In rooms with simple sloped,

peaked or gabledceilings, install smoke alarms on the ceiling

3 feet (90 cm) from the highest point of the ceiling.

Note: For complex ceiling structures, consult a safety expert for

the number of alarms required and the best locations.

€ I n very hot or cold areas where the temperature exceeds 1000F

(380C) or falls below400F (50C).

€ Less than 6 inches (15 cm) fromthe wall when mountedon the

ceiling.

Nuisance alarms could result when smoke alarms are located where

interference may occur with the sensing chamber. T o avoid nuisance

alarms, DO N OT place smoke alarms:

€ In high humidity areas such as bathrooms and attics. Place smoke

alarms at least 10feet (3 meters) away frombathrooms.

€ I n insect-infested areas.

€ I n poorly ventilated kitchens or garages.

€ I n very dusty and dirty areas.

€ N ear fluorescent lights. Place smoke alarms at least 5 feet

(1.5 meters) from fluorescent lights.

T his smoke alarm is suitable for residential

use. It is not to be connected to a commercial

or industrial fire alarm panel.

6. INSTALLATION AND TESTING

T his model has an optional Locking Key to better secure the alarm

to inhibit unauthorized removal. If securing the alarm is a concern,

remove and save the •Locking KeyŽfrom the back plate with needle

nosed pliers before installing the alarm. See point 12 in this section

for more details on this feature.

A. Installation

Mount to any standard or rectangular junction box with a minimum

depth of 1 inch (2.5 cm). 120V AC, 55mA operation.

WA RNIN G: Wiringshould only be installed by a licensed

electrician in accordance with the National Electrical C ode and

local codes.

WA RNING: T he circuit used to power the smoke alarm must be a

24 hour voltage circuit that cannot beturned off by a switch or a

ground fault interrupter. I t is highly recommended that smoke alarms

be wired on a separate circuit ( one with no other lights or

appliances) to ensure maximum reliability of A C power supply. For

installation of smoke alarms in Dwelling Units, it is important to

follow the National Electrical Code and local codes.

1. Electricity must be turned off at service entrance before

beginning installation to prevent electrical shock or equipment

damage.

2. Location must comply with applicable building codes.

3. Install a junction box where you plan to install the alarm. U se

standard 14 gauge wire.

4. Connect black and white wires color to color from power

connector to A C power leads.

5. For multiple station application use the orange wire to

interconnect. If unit is not to be interconnected, cap unused

wire. NOT E: T he SA 360 is interconnectable with up to 11

other units.

6. Loosen or remove screws from junction box.

7. A ttach flat side of mounting plate and tighten screws to fit

snugly against the junction box and ceiling or wall.

8. Bringpower connector through center opening.

9. Slip the paper gasket supplied with the alarm over the power

connector and then onto the mounting plate so that the four

plastic tabs on the mounting plate will hold the gasket in place.

T he gasket will prevent downward air currents from entering the

smokealarmthrough holesin the back ofthe alarm, unless

blocked off, downward air currents could prevent smoke from

enteringthe alarm. WARNING: IT IS IMPERAT IVE THAT

YOU INSERT THE GASKET WHEN INSTALLING YOUR

SMOKE ALA RM.

10. Align theplugarea on thesmoke alarmwith the cutout in the

gasket and place the smoke alarm on the mounting plate, turn

clockwise to fasten it to the mounting plate.

11. Plug wire connector into the back of the alarm.

12. If auxiliary lock is desired, insert the Locking Key into the slot

in the base of the alarm. Locking Key should •clickŽ into

position and be flush with the alarm housing. C AUTION: Do

not attempt to remove alarm without first removing the Locking

Key. If the key is not first removed, damage may result. To

remove, use a screwdriver and gently pry theLockingKey loose.

13. Test alarmoperation after installation in accordancewith

•Operation: How to TestŽinstructions.

Note: Maximum interconnect wiring length is 150 feet (50 meters).

IMPORTANT: T he SA 360 is not interconnectable with any other

model produced by another manufacturer. T he SA360 may be

interconnected only with the followingUnderwriters• Laboratories

Inc. listed smoke alarm models:

American Sensors SA 379

American Sensors SA 360

A SI Electronics (A merican Sensors) ESA 5010/ESA 5011

Dicon Safety Products Inc. 670L/LR

Dicon Safety Products Inc. 370LBX

Note: T his equipment should be installed in accordance with the

National Fire Protection A ssociation Standard 72. (National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269).

B. Testing After Installation

1. Check to see that the green •POWER ONŽlight ison. The

•POW ER ON Žlight is visible behind the slottedcase and

confirms that the smoke alarm is receiving A C power.

2. Press and hold the test button until the alarm sounds. NOT E: It

may be necessary to pressthe test button for up to 20 seconds for

an alarm to sound. An alarm is indicated by 3 loud beeps

repeating every 5 seconds. A larm may continue to sound for up

to 10 seconds after button is released.

3. A t least once a week, press the test button and hold until the

alarm sounds, then release.

NOT E: Multiple Station Only:

4. Test each alarm separately in the system.

5. Determine that the initiating alarm triggers other alarms in the

system.

7. MAINTENANCE & TROUBLESHOOTING

TEST THE ALARM WEEKLY. VACUUM EV ERY SIX MONTHS.

Your smoke alarm should be cleaned every six months to help keep

the unit working efficiently. R EMOV E POW ER T O A LA RM.

Gently vacuum through the vents of the alarm with a soft brush

attachment. K eep vacuum nozzle from touching the unit.

RE-ESTABLISH POWER T O ALARM.

Problems may be indicated by the following:

1. T he alarm does not sound upon pressing the test button.

2. T he green operating light does not remain steadily on when unit

is A C powered.

3. T he red operating light remains steadily on or off. ( i.e. does not

flash once every 45seconds, when the unit is not in alarm).

Try the following:

1. Inspect breaker or fuse in power circuit to alarm.

2. Gently vacuum as recommendedabove.

3. Call an electrician to inspect house wiring and connection to

alarms.

If these procedures do not correct the problem, do NOT attempt

repairs. If the smoke alarm is within warranty period and terms,

indicate the nature of the problem and return the unit with proof of

purchase to the point of purchase, distributor or manufacturer. See

below for instructions. Units beyond warranty cannot be

economically repaired.

FA LSE A LARMS:

A bnormal air conditions may cause the highly sensitive smoke alarm

to give a • falseŽalarm. If no fire is apparent, ventilate the room

and/or blowfresh air into the unit until the alarm stops. Once

cleared, the smoke alarm will automatically reset.

DO NOT DISCONNECT THE AC POWER SUPPLY.

Dust can lead to excess sensitivity. Vacuum as recommended above.

DO NOT PAINT THE UNIT.

8. LIMITED WARRANTY

Your A merican Sensors SA 360 smoke alarm is warranted for ten

years from the date of purchase against defect in material and

workmanship. U nits returned to Dicon G lobal Inc.

with proof of purchase date during this period as a result of such

defects will be repaired, or replaced at Dicon G lobal Inc.s

. •option, without charge. T his warranty only covers defects in

material or workmanship in normal residential use. Thiswarranty

does not cover damage resultingfrom negligent handling, misuse, or

lack of reasonable care. T his warranty is in lieu of any other

warranty either expressedor implied.

DICON GLOBA L INC. SHALL HAVE NO

LIABILIT Y FOR ANY PERSONAL INJURY OR PROPERT Y

DA MAGE, OR ANY SPECIAL INCIDENTAL, CONTINGENT

OR CONSEQUENTIA L DA MAGE OF ANY KIND RESULTING

FROM A FIRE. THE EXCLUSIVE REMEDY FOR BREACH OF

THE LIMITED WARRA NTY CONTA INED HEREIN IS T HE

REPAIR OR REPLA CEMENT OF T HE DEFECTIV E PRODUCT

AT DICON GLOBAL INC.S OPTION IN NO

CA SE SHA LL DICON GLOBAL INC.S

LIABILIT Y UNDER A NY OTHER REMEDY PRESCRIBED BY

120 VAC -IONIZA TION

SMOKE ALARM

READ CAREFULLY AND SAVE .

T his manual contains important information.

A copy of this manual must be left with the enduser.

2502-2509 (REV-1)

LAW EXCEED THE PURCHASE PRICE. YOUR SMOKE

ALA RM IS NOT A SUBSTITUTE FOR PROPERT Y,

DISABILIT Y, LIFE OR OT HER INSURANCE OF ANY KIND.

APPROPRIATE COVERAGE IS YOUR RESPONSIBILIT Y.

CONSULT YOUR INSURANCE AGENT.

T his warranty gives you specific legal rights and you may have other

rights which may vary from state to state.

U nits may be returned to point of purchase according to

retailers exchange / return policy. Or call 1-800-387-4219, for

shipping instructions and a returned goods authorization number

•RGA Žnumber, to return to Dicon Global Inc.

Returned goods must be shipped prepaid. A cheque for $5.00 is

also required for return postage

. Please mark the •R GA Žnumber

on the exterior of your package. Date code located on back of smoke

alarm.

Dicon Global Inc.

20 Steelcase Road, Unit 3

Markham, Ontario,

Canada L3R 1B2

9. AMERICAN SENSORS PRODUCTS

A merican Sensors offers a complete line of smoke alarms. Select

from this group of quality products to ensure your home is fully

protected in case of fire.

WAR NING

Smoke alarm

paper gasket (not shown-fits in between)

mounting plate

quick disconnect

power connector

BLAC K 120VAC, 60Hz

WHITE

Cap Unused Wire

Twis t Conne ctors

Ceiling

Mounting Plate

S upplied Ga sket M ust B e

Installed In Mounting Plate

Quick Disconnect

P ower C onnector

BLAC K 120VAC, 60Hz

WHITE

OR ANGE Interconnect

MODEL SA360

120VAC Dual-Ionization

Interconnectable

Smoke A larm

MULTIPLE S TATION

Smoke Alarm

Outlet B ox

SINGLE S TATION

MODEL

SA360

To Use Optional Locking Key-

R emove from mounting plate with needle nosed pliers and insert in housing

Dining Kitchen Bedroom Bedroom

Bedroom

Living R oom

Bedroom

Kitchen

Dining

Living R oom

TV R oom

Kitchen

Living

Room

BedroomBedroom

Basement

Hall

Furnace

Figure 1 Figure 2

Figure 3

Smoke alarms for limited protection

Additional smoke alarms for better coverage

T hese diagrams show smoke alarm

locations as recommended.

WAR NING

AMERICAN SEN SOR S

CA R BON MONOXIDE A LAR MS

American Sensors alsooffersacompleteline of Carbon Monoxide

Alarms including:

CO800 - Plug-In Carbon MonoxideAlarm

CO810 - 120 Volt A C Hardwire Carbon Monoxide Alarm

CO900 - Plug-In Carbon MonoxideAlarmwith Battery Back-

CO910 - Plug-In Carbon MonoxideAlarmwith Digital LED

Display

CO920 - Plug-In Carbon MonoxideAlarmwith Digital LED

andBack-UpPower Source

CO1100 - Battery PoweredCarbon MonoxideAlarm for Table

Top, Travel or Wall Mount

Model

SA 310

SA 320

SA 358

SA 500

SA 900

SA 360

SA 379

Description

Basic Model

General Purpose

Model

with Alarm-Pause

Feature

Hall and Stairways M odel

with Emergency Light

ExtendedLife

Multi-Location with

Alarm-Pause®Model

LongLife Multi-

Location with

Alarm-Pause®Model

Professional Hardwire

Multi-Location Model

Professional Hardwire

with Battery Back-Up

andAlarm-Pause®

Model

Power Source

9V Battery

2-9V Batteries

ExtendedLife

Battery with

3 Year Warranty

LongLife Lithium

battery with 10

year warranty

120 Volt A C

120 Volt A C with

9 Volt Back-U p

Battery

Smoke A larm

Technology

Ionization

AMERICAN SENSORS SMOKE A LAR MS

SMOKE ALARM MANUAL

Ionization Type Model - 120 VAC Hardwire

€Model SA360 - Professional Multi-Location Model 120 Volt

A C H ardwire Smoke Alarm. T his model is interconnectable with

upto 11 other units.

Important information about your smoke alarm

€ Install alarms outside of every bedroom area and on every floor of

your home. Please refer to Section 3 •W here to Locate Smoke

AlarmsŽfor details.

€ Test the alarm weekly by pressingand holdingthetest button for

up to 20 seconds until the alarm sounds.

€

T he model described in this manual is designed for single

family residences, includinghomes and apartments rather than

commercial or industrial use.

Smoke Alarm Safety Features

€ Dual-Ionization Chambers - A dvanced design responds to visible

or invisible particles of combustion (smoke) to sense fires in their

earliest stages. C ompensates for changes in humidity and

temperature to virtually eliminate •nuisanceŽalarms caused by

normal atmospheric changes in the home.

€OperatingLight (LED) - A continuous green light located behind

the slotted case indicates the smoke alarm is receiving AC power.

€ Interconnection - Interconnection facilities for up to 11 other

units, usingonly three wires, including AC power. W hen one

alarm sounds, all properly interconnected smoke alarms follow.

NOT E: Interconnect only with the models specified in Section 6.

€ Alarm Source Indicator - The red operating light in the unit

originatingthealarmwill flash rapidly in the event of an alarm.

With interconnected units, this featureallows for an easycheck to

determine the originator.

€Locking Key - T he auxiliary locking key provided can be used to

lock the smoke alarm to the mounting plate. T his helps to reduce

the risk of unauthorized removal.

€ Sensitivity Test Button - Test sensitivity, as well as circuitry and

horn. With interconnectedunits, activatingtest button on one

unit will cause all properly interconnected units to sound. A n

important and convenient check of system integrity.

€ Quick Disconnect Power Connector - For easy installation,

connect the wires separately from the unit and then pluginto the

back of the unit.

€ Detachable Mounting Plate - For easily securing the alarm to the

junction box.

CONTENTS OF THIS MANUAL

1. CAPA BILIT IES AND LIMITATIONS OF SMOKE ALARMS

2. SAFETY TIPS

3. W HERE TO LOCATE SMOKE ALARMS

4. NFPA RECOMMENDATIONS

5. LOCAT IONS TO AVOID

6. INSTA LLATION AND TESTING

7. MAINTENANCE A ND T ROUBLESHOOT ING

8. LIMIT ED WA RRANTY

9. OTHER AMERICAN SENSORS PRODUCTS

1. CAPABILITIES AND LIMITATIONS OF SMOKE ALARMS

A merican Sensors smoke alarms are designed to provide early

warning of fire and smoke at reasonable cost. Early warning can

mean the difference between a safe escape and no escape at all.

W hile smoke alarmscan provide invaluable protection for you and

your family, they do have limitations.

€ Smoke alarms cannot work without power. Battery operated

alarms will not work without proper batteries, with dead batteries

or if batteries are not properly installed. A C powered alarms will

not work if their AC power supply iscut off by an electrical fire,

an open fuse, a circuit breaker or any other reason.

If you are concerned about the reliability of either batteries or your

AC power supply for any of theabovereasons, youshouldinstall

in your home both A C and battery powered smoke alarms for

added security. A merican Sensors also offers the SA 379 model

which is A C powered with battery back-up.

€ Smoke alarms are incapable of soundingthe alarm until smoke

reaches the sensing chamber. A nythingpreventing smoke from

reaching the alarm may delay or prevent an alarm. A smoke alarm

cannot detect fire in the walls, chimney or roof unless and until a

significant amount of smoke reaches the alarm. A closed door may

prevent smoke from reaching an alarm on the other side of the

door. A smoke alarm may not sense a fire on another floor of a

home. For example, a basement smoke alarmmay not detect a fire

which started on the first or second floor.

€ Smoke alarms may not be heard. T he loudness of the horn in

your alarmmeetscurrent standards. However, the sound may be

blocked by distance, closed doors, or ambient noise such as traffic

or a stereo. Smoke alarms may not be heard by persons who are

hardof hearing.

For these reasons, a smoke alarm should be installed in every

room or at least on every level of your home. American Sensors

recommends that hardwire A C Powered smoke alarms be

interconnected, so that onealarmwill trigger all other alarms to

soundtheir alarms.

€ Smoke alarms are not fool-proof. Smoke alarms may not always

sense every kind of fire. T hey cannot be expected to sense fires

caused by carelessness or by safety hazards. T hey may not give

early warning of fast growing fires caused by smoking in bed,

violent explosions, escaping gas, improper storage of flammable

materials, overloaded electrical circuits, natural causes such as

lightning, children playingwith matches, or arson.

€ Smoke alarms are not substitutes for property, disability, life or

other insurance of any kind. Home owners and renters should

continue to insure their lives and property. Consult your insurance

agent.

€ Smoke alarms have limited lives. One or more of the many

componentscouldfail at anytime. Therefore, test your smoke

alarmweekly. Clean and takecareof it asdescribed in this

manual. Repair or replacethe smokealarmwhen it fails totest

properly. Your smoke alarm should be replaced if it is ten years

old.

€

A photoelectronic smoke alarm senses smoke using an electronic

photo receptor to sense the scattering of light by smoke particles.

2. SAFETY TIPS

Properly installed and maintained smoke alarms are an essential part

of a goodhome fire safety program. Your fire safety program should

also include a review of fire hazards and the elimination of

dangerous conditions whenever possible. C onsider the following tips:

€ Use smoking materials properly. N ever smoke in bed.

€ Keep matches and cigarette lighters away from children.

€ Store flammable materials in proper containers. N ever use them

near an open flame or sparks.

€ Keep electrical appliances in good condition. Do not overload

electrical circuits.

€ Keep stoves, fireplaces, chimneys, and barbecuegrills greasefree.

Make sure they are properly installed and away from any

combustible materials.

€ Keep portable heaters and open flames such as candles away from

combustible material.

€ Do not allow rubbish to accumulate.

€ Keep a supply of extra batteries on hand for your battery powered

smoke alarms.

€ Do not stand too close to the alarm when the unit is in alarm as the

loud horn could damage your hearing.

Never disconnect the battery or the A C power on any type of smoke

alarm to silence a nuisance alarm. C lear the area of smoke by opening

doors and windows or fanning the smoke away.

Most important, when fire strikes, a prepared

and practiced escape plan can make the difference between life and

death. Develop an escape plan and practice it with the entire family,

includingsmall children.

€ Ensure all family members are familiarized with the alarm signal.

€ Prepare an escape plan. Drawa Floor Plan of Your Homeand

determine two exits from each room. T here should be a way to get

out of each bedroom without openingthe door.

€ Have Fire Drills Often. Practice your Escape and BE PREPARED.

€ Decide on a meeting place at a safe distance from your home.

IN CASE OF FIRE

€ Don•t waste time collecting possessions after a fire starts.

€ A rouse all occupants and leave the building. Your most valuable

possession is your life.

€ Doors can mean escape or death. Never open doors without first

checking for heat. Test them with your hands, if they feel warm, fire

may be walled up behind them - leave closed and find another

escape route.

€ Call the fire department from OU TSIDE the building.

€ If trapped inside, stay close to the floor, cover mouth with cloth,

conserve breath as you crawl to safety.

€ Keep all doors and windows closed except for escape purposes.

€ NEV ER re-enter a burningbuilding.

€ Keep your family in a pre-arranged meeting place after your escape.

Your local fire department may be able to offer you additional ideas

for safety and escape plans in the home.

3a. WHERE TOLOCATE SMOKE ALARMS

As a minimum, smoke alarms should be located between sleeping

areas and potential sources of fire such as a kitchen, heated garage or

basement. I n single storey homes with one sleepingarea, an alarm

should be installed in the hallway outside the bedrooms (see Figure

1). In single storey homes with two separate sleepingareas, a

minimum of two alarms are required, one outside each sleeping area

(see Figure 2). In multi-level or split-level homes, as a minimum, an

alarm should be installed outside each sleeping area, in the basement

and at every level of the home (see Figure 3).

€ In every room of your home (except the bathroom): R esearch

indicates that substantial increases in warning time can be obtained

with each properly installed, additional alarm.

€ In bedrooms: In anticipation of firesoriginatingwithin these rooms,

caused by faulty wiring, lamps, appliances, smokingor other hazards.

€ In hallways: A t adistance no greater than 13 feet (4 meters) from

the farthest wall and no greater than 26 feet (8 meters) from the

next alarm.

€ In the center of a room or hallway: A s it is impossible to predict the

source of a fire. If it is necessary to place the alarm on a wall, always

locate the top of the smoke alarm 4-6 inches (10-15 cm) from the

ceiling.

€ A s needed: To compensate for closed doors and other obstacles that

may interfere with the path of smoke toan alarm. T hey mayalso

prevent occupants on one side of a closed door from hearing a alarm

on the other side of the door.

€ Model SA360 - Professional Multi-Location model can be located

in any area of the home.

READ •CAPABILITIES AND LIMITATIONS OF SMOKE

ALA RMSŽin Section 1of thismanual.

Your local fire department or insurancecompany may beable togive

you further advice on the best smoke alarm locations in your home.

Call them and ask.

T here are two different types of smoke alarm technology

currently in general use: ionization and photoelectronic. While

both types of technology are suitable for general residential use,

an ionization alarm will normally respond faster to fast flaming

fires, while a photoelectronic alarm may be more sensitive to

detecting slow smoldering fires. Because home fires develop in

different ways and are often unpredictable in their growth, it is

impossible topredict which type of alarm will providetheearliest

warning. For best home protection install at least one

photoelectronic and one ionization smoke alarm on each level of

your home. Model SA 360 is an ionization typesmoke alarm.

Ionization Technology vs.

Photoelectronic Technology

Smoke A larms

3b. WHERE TO LOCATE SMOKE ALARMS IN MOBILE HOMES

N OT E: Power supply must be 120 V olts A C for model SA 360.

In mobile homes built after 1978 locate the smoke alarm as

describedabove.

Older mobile homes may have little or no insulation compared to

the ones built post 1978. T hese uninsulated exteriors can disrupt

airflowaround the smoke alarmin hotter or colder weather. Locate

the alarm only on interior walls 4Žto 6Ž( 10 to 15 cm) from ceiling

1. if you own an older mobile home or 2. if you notice theexterior

walls and/or ceiling are noticeably cold or warm or 3. if you are

uncertain about the quality of insulation.

Regardless of the age of the mobile home, locate alarms throughout

to ensure maximum protection. Follow the location instructions in

this manual.

4. NFPA RECOMMENDATIONS

For your information, the N ational Fire Protection Association•s

Standard 72 reads as follows:

2-2.1.1.1

Smoke alarms shall be installed outside of each separate sleeping

area in the immediate vicinity of the bedrooms and on each

additional storey of the family living unit, including basements and

excluding crawl spaces and unfinished attics. In new construction a

smoke alarm also shall be installed in each sleeping room.

A-2.5.2.1 Smoke Detection- AreMore SmokeAlarms Desirable?T he

required number of smoke alarms might not providereliable early

warning protection for those areas separated by a door from the

areas protected by the required smoke alarms. For this reason, it is

recommended that the householder consider the use of additional

smoke alarmsfor those areasfor increasedprotection. T he

additional areas includethe basement, bedrooms, diningroom,

furnace room, utility room, andhallways not protected by the

required smoke alarms. The installation of smoke alarms in

kitchens, attics(finishedor unfinished), or garages is not

normally recommended, as these locationsoccasionally

experience conditions that can result in improper operation.

5. LOCATIONS TOAVOID

Avoid locations where smoke may not reach the alarm in time to

provide early warning, or where the alarm may not be effective.

DO NOT PLACE SMOKE ALA RMS:

€ In turbulent air fromfans, doors, windows, etc. The rapidair

movement may prevent combustion particles from entering the

alarm.

€ I n dead air spaces such as at the peak of an •A Žframe ceiling.

•Dead airŽ at the top may prevent smoke from reaching the alarm

in time to provide early warning. In rooms with simple sloped,

peaked or gabled ceilings, install smoke alarms on the ceiling

3 feet (90 cm) from the highest point of the ceiling.

Note: For complex ceiling structures, consult a safety expert for

the number of alarms requiredand the best locations.

€ I n very hot or cold areas where the temperature exceeds 1000F

(380C) or falls below400F (50C).

€ Less than 6 inches (15 cm) fromthe wall when mountedon the

ceiling.

Nuisance alarms could result when smoke alarms are located where

interference may occur with the sensing chamber. T o avoid nuisance

alarms, DO N OT place smoke alarms:

€ In high humidity areas such as bathrooms and attics. Place smoke

alarms at least 10 feet (3 meters) away from bathrooms.

€ I n insect-infested areas.

€ I n poorly ventilated kitchens or garages.

€ I n very dusty and dirty areas.

€ N ear fluorescent lights. Place smoke alarms at least 5 feet

(1.5 meters) from fluorescent lights.

T his smoke alarm is suitable for residential

use. It is not to be connected to a commercial

or industrial fire alarm panel.

6. INSTALLATION AND TESTING

T his model has an optional Locking Key to better secure the alarm

to inhibit unauthorized removal. If securing the alarm is a concern,

remove and save the •Locking KeyŽfrom the back plate with needle

nosed pliers before installing the alarm. See point 12 in this section

for more details on this feature.

A. Installation

Mount to any standard or rectangular junction box with a minimum

depth of 1 inch (2.5 cm). 120V A C, 55mA operation.

WA RNIN G: Wiringshould only be installed by a licensed

electrician in accordance with the National Electrical C ode and

local codes.

WA RNIN G: T he circuit used to power the smoke alarm must be a

24 hour voltage circuit that cannot beturned off bya switch or a

ground fault interrupter. It is highly recommended that smoke alarms

be wired on a separate circuit ( one with no other lights or

appliances) to ensure maximum reliability of A C power supply. For

installation of smoke alarms in Dwelling Units, it is important to

follow the National Electrical C ode and local codes.

1. Electricity must be turned off at service entrance before

beginning installation to prevent electrical shock or equipment

damage.

2. Location must comply with applicable building codes.

3. Install a junction box where you plan to install the alarm. U se

standard 14 gauge wire.

4. Connect black and white wires color to color from power

connector to A C power leads.

5. For multiple station application use the orange wire to

interconnect. If unit is not to be interconnected, cap unused

wire. NOT E: T he SA 360 is interconnectable with up to 11

other units.

6. Loosen or remove screws from junction box.

7. A ttach flat side of mounting plate and tighten screws to fit

snugly against the junction box and ceiling or wall.

8. Bringpower connector through center opening.

9. Slip the paper gasket supplied with the alarm over the power

connector and then onto the mounting plate so that the four

plastic tabs on the mounting plate will hold the gasket in place.

T he gasket will prevent downward air currents from entering the

smoke alarmthrough holesin the back of thealarm, unless

blocked off, downward air currents could prevent smoke from

enteringthe alarm. WARNING: IT IS IMPERAT IVE THAT

YOU INSERT THE GASKET WHEN INSTALLING YOUR

SMOKE ALA RM.

10. Align the plugarea on the smokealarmwith the cutout in the

gasket and place the smoke alarm on the mounting plate, turn

clockwise to fasten it to the mounting plate.

11. Plug wire connector into the back of the alarm.

12. If auxiliary lock is desired, insert the Locking Key into the slot

in the base of the alarm. Locking Key should •clickŽinto

position and be flush with the alarm housing. CAU TI ON: Do

not attempt to remove alarm without first removing the Locking

Key. If the key is not first removed, damage may result. To

remove, use a screwdriver and gently pry theLockingKey loose.

13. Test alarm operation after installation in accordancewith

•Operation: How to TestŽ instructions.

Note: Maximum interconnect wiring length is 150 feet (50 meters).

IMPORTANT: T he SA 360 is not interconnectable with any other

model produced by another manufacturer. T he SA 360 may be

interconnected only with the followingUnderwriters• Laboratories

Inc. listed smoke alarm models:

American Sensors SA379

American Sensors SA360

A SI Electronics (A merican Sensors) ESA 5010/ESA 5011

Dicon Safety Products Inc. 670L/LR

Dicon Safety Products Inc. 370LBX

Note: T his equipment should be installed in accordance with the

National Fire Protection Association Standard 72. (National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269).

B. Testing After Installation

1. Check to seethat thegreen •POWER ONŽlight is on. The

•POW ER ON Žlight is visible behind the slotted case and

confirms that the smoke alarm is receiving A C power.

2. Press and hold the test button until the alarm sounds. N OT E: It

may be necessary to pressthe test button for up to 20 seconds for

an alarm to sound. A n alarm is indicated by 3 loud beeps

repeating every 5 seconds. A larm may continue to sound for up

to 10 seconds after button is released.

3. A t least once a week, press the test button and hold until the

alarm sounds, then release.

NOT E: Multiple Station Only:

4. Test each alarm separately in the system.

5. Determine that the initiating alarm triggers other alarms in the

system.

7. MAINTENANCE & TROUBLESHOOTING

TEST THE ALARM WEEKLY. VA CUUM EVERY SIX MONTHS.

Your smoke alarm should be cleaned every six months to help keep

the unit working efficiently. R EMOV E POW ER T O A LA RM.

Gently vacuum through the vents of the alarm with a soft brush

attachment. K eep vacuum nozzle from touching the unit.

RE-ESTABLISH POWER T O ALARM.

Problems may be indicated by the following:

1. T he alarm does not sound upon pressing the test button.

2. T he green operating light does not remain steadily on when unit

is A C powered.

3. T he red operating light remains steadily on or off. ( i.e. does not

flash once every 45 seconds, when the unit is not in alarm).

Try the following:

1. Inspect breaker or fuse in power circuit to alarm.

2. Gently vacuum as recommended above.

3. Call an electrician to inspect house wiring and connection to

alarms.

If these procedures do not correct the problem, do NOT attempt

repairs. If the smoke alarm is within warranty period and terms,

indicate the nature of the problem andreturn the unit with proof of

purchase to the point of purchase, distributor or manufacturer. See

below for instructions. Units beyond warranty cannot be

economically repaired.

FA LSE ALARMS:

A bnormal air conditions may cause the highly sensitive smoke alarm

to give a • falseŽalarm. If no fire is apparent, ventilate the room

and/or blowfresh air into the unit until the alarm stops. Once

cleared, the smoke alarm will automatically reset.

DO NOT DISCONNECT THE AC POWER SUPPLY.

Dust can lead to excess sensitivity. Vacuum as recommended above.

DO NOT PAINT THE UNIT.

8. LIMITED WARRANTY

Your A merican Sensors SA 360 smoke alarm is warranted for ten

years from the date of purchase against defect in material and

workmanship. U nits returned to Dicon G lobal Inc.

with proof of purchase date during this period as a result of such

defects will be repaired, or replaced at Dicon G lobal Inc.s

. •option, without charge. T his warranty only covers defects in

material or workmanship in normal residential use. Thiswarranty

does not cover damage resultingfrom negligent handling, misuse, or

lack of reasonable care. T his warranty is in lieu of any other

warranty either expressedor implied.

DICON GLOBAL INC. SHALL HA VE NO

LIABILIT Y FOR ANY PERSONA L INJURY OR PROPERT Y

DA MAGE, OR ANY SPECIAL INCIDENTA L, CONTINGENT

OR CONSEQUENT IAL DAMAGE OF A NY KIND RESULTING

FROM A FIRE. THE EXCLUSIV E REMEDY FOR BREACH OF

THE LIMITED WA RRANTY CONTAINED HEREIN IS THE

REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT

AT DICON GLOBAL INC.S OPT ION IN NO

CA SE SHALL DICON GLOBAL INC.S

LIABILIT Y UNDER ANY OT HER REMEDY PRESCRIBED BY

120 VAC -IONIZA TION

SMOKE ALARM

READ CAREFULLY AND SAVE.

T his manual contains important information.

A copy of this manual must be left withthe end user.

2502-2509 (REV-1)

LAW EXCEED T HE PURCHASE PRICE. YOUR SMOKE

ALA RM IS NOT A SUBSTITUTE FOR PROPERTY,

DISABILIT Y, LIFE OR OTHER INSURANCE OF ANY KIND.

APPROPRIAT E COVERAGE IS YOUR RESPONSIBILITY.

CONSULT YOUR INSURANCE AGENT.

T his warranty gives you specific legal rights and you may have other

rights which may vary from state to state.

U nits may be returned to point of purchase according to

retailers exchange / return policy. Or call 1-800-387-4219, for

shipping instructions and a returned goods authorization number

•RGA Žnumber, to return to Dicon Global Inc.

Returned goods must be shipped prepaid. A cheque for $5.00 is

also required for return postage

. Please mark the •R GA Žnumber

on the exterior of your package. Date code located on back of smoke

alarm.

Dicon Global Inc.

20 Steelcase Road, Unit 3

Markham, Ontario,

Canada L3R 1B2

9. AMERICAN SENSORS PRODUCTS

A merican Sensors offers a complete line of smoke alarms. Select

from this group of quality products to ensure your home is fully

protected in case of fire.

WAR NING

Smoke alarm

paper gasket (not s hown-fits in between)

mounting plate

quick disconnect

power connector

BLAC K 120VAC, 60Hz

WHITE

Cap Unused Wire

Twis t Conne ctors

Ceiling

Mounting Pla te

S upplied Ga sket M ust B e

Installed In Mounting P late

Quick Disconnect

P ower C onnector

BLAC K 120VAC, 60Hz

WHITE

OR ANGE Interconnect

MODEL SA360

120VAC Dual-Ionization

Interconnectable

Smoke A larm

MULTIPLE S TATION

Smoke Alarm

Outlet B ox

SINGLE S TATION

MODEL

SA360

To Use Optional Locking Key-

R emove from mounting plate with needle nos ed pliers and insert in housing

Dining Kitchen Bedroom Bedroom

Bedroom

Living R oom

Bedroom

Kitchen

Dining

Living R oom

TV R oom

Kitchen

Living

Room

BedroomB edroom

Basement

Hall

Furnace

Figure 1 Figure 2

Figure 3

Smoke alarms for limited protection

Additional smoke alarms for better coverage

T hese diagrams show smoke alarm

locations as recommended.

WAR NING

AMERICAN SENSORS

CA R BON MONOXIDE A LAR MS

American Sensors alsooffersacomplete line of Carbon Monoxide

Alarms including:

CO800 - Plug-In C arbon MonoxideAlarm

CO810 - 120 Volt A C Hardwire Carbon Monoxide Alarm

CO900 - Plug-In C arbon MonoxideAlarmwith Battery Back-

CO910 - Plug-In C arbon MonoxideAlarmwith Digital LED

Display

CO920 - Plug-In C arbon MonoxideAlarmwith Digital LED

andBack-UpPower Source

CO1100 - Battery Powered Carbon Monoxide Alarmfor Table

Top, Travel or Wall Mount

Model

SA 310

SA 320

SA 358

SA 500

SA 900

SA 360

SA 379

Description

Basic Model

General Purpose

Model

with Alarm-Pause

Feature

Hall and Stairways M odel

with Emergency Light

ExtendedLife

Multi-Location with

Alarm-Pause®Model

LongLife Multi-

Location with

Alarm-Pause®Model

Professional Hardwire

Multi-Location Model

Professional Hardwire

with Battery Back-Up

andAlarm-Pause®

Model

Power Source

9V Battery

2-9V Batteries

ExtendedLife

Battery with

3 Year Warranty

LongLife Lithium

battery with 10

year warranty

120 Volt A C

120 Volt A C with

9 Volt Back-U p

Battery

Smoke A larm

Technology

Ionization

AMERICAN SENSORS SMOKE ALARMS

SMOKE ALARM MANUAL

Ionization Type Model - 120 VAC Hardwire

€Model SA360 - Professional Multi-Location Model 120 Volt

A C Hardwire Smoke A larm. T his model is interconnectable with

upto 11 other units.

Important information about your smoke alarm

€ Install alarms outside of every bedroom area and on every floor of

your home. Please refer to Section 3 •W here to Locate Smoke

AlarmsŽfor details.

€ Test the alarmweekly by pressing and holdingthetest button for

up to 20 seconds until the alarm sounds.

€

T he model described in this manual is designed for single

family residences, including homes and apartments rather than

commercial or industrial use.

Smoke Alarm Safety Features

€ Dual-Ionization Chambers - A dvanced design responds to visible

or invisible particles of combustion (smoke) to sense fires in their

earliest stages. C ompensates for changes in humidity and

temperature to virtually eliminate •nuisanceŽalarms caused by

normal atmospheric changes in the home.

€OperatingLight (LED) - A continuous green light located behind

the slotted case indicates the smoke alarm is receiving AC power.

€ Interconnection - I nterconnection facilities for up to 11 other

units, using only three wires, including AC power. When one

alarm sounds, all properly interconnected smoke alarms follow.

NOT E: Interconnect only with the models specified in Section 6.

€ Alarm Source Indicator - T he red operatinglight in the unit

originatingthealarmwill flash rapidly in the event of an alarm.

With interconnected units, this featureallows for an easy check to

determine the originator.

€LockingKey - T he auxiliary locking key providedcan beused to

lock the smoke alarm to the mounting plate. T his helps to reduce

the risk of unauthorized removal.

€ Sensitivity Test Button - Test sensitivity, as well as circuitry and

horn. With interconnectedunits, activatingtest button on one

unit will cause all properly interconnected units to sound. An

important and convenient check of system integrity.

€ Quick Disconnect Power Connector - For easy installation,

connect the wires separately from the unit and then pluginto the

back of the unit.

€ Detachable Mounting Plate - For easily securing the alarm to the

junction box.

CONTENTS OF THIS MANUAL

1. CAPABILIT IES AND LIMITATIONS OF SMOKE ALARMS

2. SAFET Y TIPS

3. WHERE TO LOCATE SMOKE ALA RMS

4. NFPA RECOMMENDATIONS

5. LOCAT IONS TO AVOID

6. INSTALLATION AND TEST ING

7. MAINT ENANCE AND TROUBLESHOOT ING

8. LIMITED WARRANTY

9. OTHER AMERICA N SENSORS PRODUCTS

1. CAPABILITIES AND LIMITATIONS OF SMOKE ALARMS

A merican Sensors smoke alarms are designed to provide early

warningof fire and smoke at reasonable cost. Early warning can

mean the difference between a safe escape and no escape at all.

While smoke alarms can provide invaluable protection for you and

your family, they do have limitations.

€ Smoke alarms cannot work without power. Battery operated

alarms will not work without proper batteries, with dead batteries

or if batteries are not properly installed. A C powered alarms will

not work if their AC power supply iscut off by an electrical fire,

an open fuse, a circuit breaker or any other reason.

If you are concerned about the reliability of either batteries or your

AC power supply for any of the above reasons, youshouldinstall

in your home both A C and battery powered smoke alarms for

added security. A merican Sensors also offers the SA 379 model

which is A C powered with battery back-up.

€ Smoke alarms are incapable of sounding the alarm until smoke

reaches the sensing chamber. A nything preventing smoke from

reaching the alarm may delay or prevent an alarm. A smoke alarm

cannot detect fire in the walls, chimney or roof unless and until a

significant amount of smoke reaches the alarm. A closed door may

prevent smoke from reachingan alarm on the other side of the

door. A smoke alarm may not sense a fire on another floor of a

home. For example, a basement smokealarmmay not detect a fire

which started on the first or second floor.

€ Smoke alarms may not be heard. T he loudness of the horn in

your alarmmeetscurrent standards. However, thesoundmay be

blocked by distance, closed doors, or ambient noise such as traffic

or a stereo. Smoke alarms may not be heard by persons who are

hardof hearing.

For these reasons, a smoke alarm should be installed in every

room or at least on every level of your home. American Sensors

recommends that hardwire A C Powered smoke alarms be

interconnected, so that onealarmwill trigger all other alarms to

sound their alarms.

€ Smoke alarms are not fool-proof. Smoke alarms may not always

sense every kind of fire. T hey cannot be expected to sense fires

caused by carelessnessor by safety hazards. T hey may not give

early warning of fast growing fires caused by smoking in bed,

violent explosions, escapinggas, improper storage of flammable

materials, overloaded electrical circuits, natural causes such as

lightning, children playingwith matches, or arson.

€ Smoke alarms are not substitutes for property, disability, life or

other insurance of any kind. H ome owners and renters should

continue to insure their lives and property. Consult your insurance

agent.

€ Smoke alarms have limited lives. One or more of the many

componentscould fail at anytime. Therefore, test your smoke

alarmweekly. Clean and takecareofit asdescribed in this

manual. Repair or replacethe smoke alarmwhen it failsto test

properly. Your smoke alarm should be replaced if it is ten years

old.

€

A photoelectronic smoke alarm senses smoke using an electronic

photo receptor to sense the scattering of light by smoke particles.

2. SAFETY TIPS

Properly installed and maintained smoke alarms are an essential part

of a good home fire safety program. Your fire safety program should

also include a review of fire hazards and the elimination of

dangerous conditions whenever possible. Consider the following tips:

€ Use smoking materials properly. N ever smoke in bed.

€ Keep matches and cigarette lighters away from children.

€ Store flammable materials in proper containers. Never use them

near an open flame or sparks.

€ Keep electrical appliances in good condition. Do not overload

electrical circuits.

€ Keep stoves, fireplaces, chimneys, and barbecue grills greasefree.

Make sure they are properly installed and away from any

combustible materials.

€ Keep portable heaters and open flames such as candles away from

combustible material.

€ Do not allow rubbish to accumulate.

€ Keep a supply of extra batteries on hand for your battery powered

smoke alarms.

€ Do not stand too close to the alarm when the unit is in alarm as the

loudhorn could damage your hearing.

Never disconnect the battery or the A C power on any type of smoke

alarm to silence a nuisance alarm. C lear the area of smoke by opening

doors and windows or fanning the smoke away.

Most important, when fire strikes, a prepared

and practicedescape plan can make the difference between life and

death. Develop an escape plan and practice it with the entire family,

includingsmall children.

€ Ensure all family members are familiarized with the alarm signal.

€ Prepare an escape plan. Drawa Floor Plan ofYour Homeand

determine two exits from each room. T here should be a way to get

out of each bedroom without opening the door.

€ Have Fire Drills Often. Practice your Escape and BE PREPARED.

€ Decide on a meeting place at a safe distance from your home.

IN CASE OF FIRE

€ Don•t waste time collecting possessions after a fire starts.

€ A rouse all occupants and leave the building. Your most valuable

possession is your life.

€ Doors can mean escape or death. Never open doors without first

checking for heat. Test them with your hands, if they feel warm, fire

may be walled up behind them - leave closed and find another

escape route.

€ Call the fire department from OU TSIDE the building.

€ If trapped inside, stay close to the floor, cover mouth with cloth,

conserve breath as you crawl to safety.

€ Keep all doors and windows closed except for escape purposes.

€ NEV ER re-enter a burningbuilding.

€ Keep your family in a pre-arranged meeting place after your escape.

Your local fire department may be able to offer you additional ideas

for safety and escape plans in the home.

3a. WHERE TO LOCATE SMOKE ALARMS

As a minimum, smoke alarms should be located between sleeping

areas and potential sources of fire such as a kitchen, heated garage or

basement. In single storey homes with one sleeping area, an alarm

should be installed in the hallway outside the bedrooms (see Figure

1). In single storey homes with two separate sleepingareas, a

minimum of two alarms are required, one outside each sleeping area

(see Figure 2). In multi-level or split-level homes, asa minimum, an

alarm should be installed outside each sleeping area, in the basement

and at every level of the home (see Figure 3).

€ In every room of your home (except the bathroom): Research

indicates that substantial increases in warning time can be obtained

with each properly installed, additional alarm.

€ In bedrooms: In anticipation of fires originating within these rooms,

caused by faulty wiring, lamps, appliances, smokingor other hazards.

€ In hallways: At adistance nogreater than 13 feet (4 meters) from

the farthest wall and no greater than 26 feet (8 meters) from the

next alarm.

€ In the center of a room or hallway: A s it is impossible to predict the

source of a fire. If it is necessary to place the alarm on a wall, always

locate the top of the smoke alarm 4-6 inches (10-15 cm) from the

ceiling.

€ A s needed: To compensate for closed doors and other obstacles that

may interfere with the path ofsmoke toan alarm. T hey may also

prevent occupants on one side of a closed door from hearinga alarm

on the other side of the door.

€ Model SA360 - Professional Multi-Location model can belocated

in any area of the home.

READ •CAPA BILIT IES A ND LIMITATIONS OF SMOKE

ALA RMSŽin Section 1 of this manual.

Your local fire department or insurancecompany may beable togive

you further advice on the best smoke alarm locations in your home.

Call them and ask.

T here are two different types of smoke alarm technology

currently in general use: ionization and photoelectronic. While

both types of technology are suitable for general residential use,

an ionization alarm will normally respond faster to fast flaming

fires, while a photoelectronic alarm may be more sensitive to

detecting slow smoldering fires. Because home fires develop in

different ways and are often unpredictable in their growth, it is

impossible topredict which type of alarm will providethe earliest

warning. For best home protection install at least one

photoelectronic and one ionization smoke alarm on each level of

your home. Model SA 360 is an ionization typesmoke alarm.

Ionization Technology vs.

Photoelectronic Technology

Smoke A larms

3b. WHERE TO LOCATE SMOKE ALARMS IN MOBILE HOMES

N OT E: Power supply must be 120 Volts A C for model SA360.

In mobile homes built after 1978 locate the smoke alarm as

described above.

Older mobile homes may have little or no insulation compared to

the ones built post 1978. T hese uninsulated exteriors can disrupt

airflowaround the smoke alarmin hotter or colder weather. Locate

the alarm only on interior walls 4Žto 6Ž(10 to 15 cm) from ceiling

1. if you own an older mobile home or 2. if you noticethe exterior

walls and/or ceiling are noticeably cold or warm or 3. if you are

uncertain about the quality of insulation.

Regardless of the age of the mobile home, locate alarms throughout

to ensure maximum protection. Follow the location instructions in

this manual.

4. NFPA RECOMMENDATIONS

For your information, the N ational Fire Protection Association•s

Standard 72 reads as follows:

2-2.1.1.1

Smoke alarms shall be installed outside of each separate sleeping

area in the immediate vicinity of the bedrooms and on each

additional storey of the family living unit, includingbasements and

excluding crawl spaces and unfinished attics. I n new construction a

smoke alarm also shall be installed in each sleeping room.

A-2.5.2.1 SmokeDetection- Are More Smoke AlarmsDesirable?T he

requirednumber of smoke alarms might not providereliable early

warningprotection for those areas separated by a door from the

areas protected by therequiredsmoke alarms. For this reason, it is

recommendedthat the householder consider the use of additional

smoke alarms for thoseareasfor increased protection. The

additional areasincludethebasement, bedrooms, dining room,

furnace room, utility room, andhallways not protected by the

requiredsmokealarms. Theinstallation of smoke alarmsin

kitchens, attics (finishedor unfinished), or garagesis not

normally recommended, as theselocations occasionally

experience conditionsthat can result in improper operation.

5. LOCATIONS TOAVOID

Avoid locations where smoke may not reach thealarm in timeto

provide early warning, or where the alarm may not be effective.

DO NOT PLACE SMOKE ALAR MS:

€ In turbulent air fromfans, doors, windows, etc. Therapid air

movement may prevent combustion particles from entering the

alarm.

€ In dead air spaces such as at the peak of an •AŽ frame ceiling.

•Dead airŽ at the top may prevent smoke from reaching the alarm

in time to provide early warning. In rooms with simple sloped,

peaked or gabled ceilings, install smoke alarms on the ceiling

3 feet (90 cm) from the highest point of the ceiling.

Note: For complex ceiling structures, consult a safety expert for

the number of alarms required and the best locations.

€ In very hot or cold areas where the temperature exceeds 1000F

(380C) or falls below 400F (50C).

€ Less than 6 inches (15 cm) from thewall when mounted on the

ceiling.

Nuisance alarms could result when smoke alarms are located where

interference may occur with the sensing chamber. T o avoid nuisance

alarms, DO N OT place smoke alarms:

€ In high humidity areas such as bathrooms and attics. Place smoke

alarms at least 10feet (3 meters) away frombathrooms.

€ In insect-infested areas.

€ In poorly ventilated kitchens or garages.

€ In very dusty and dirty areas.

€ Near fluorescent lights. Place smoke alarms at least 5 feet

(1.5 meters) from fluorescent lights.

T his smoke alarm is suitable for residential

use. It is not to be connected to a commercial

or industrial fire alarm panel.

6. INSTALLATION AND TESTING

T his model has an optional Locking Key to better secure the alarm

to inhibit unauthorized removal. If securing the alarm is a concern,

remove and save the •Locking KeyŽfrom the back plate with needle

nosed pliers before installing the alarm. See point 12 in this section

for more details on this feature.

A. Installation

Mount to any standard or rectangular junction box with a minimum

depth of 1 inch (2.5 cm). 120V AC, 55mA operation.

WA RNIN G: Wiring should only be installed by a licensed

electrician in accordance with the N ational Electrical Code and

local codes.

WA RNING: T he circuit used to power the smoke alarm must be a

24 hour voltagecircuit that cannot beturned off by a switch or a

ground fault interrupter. It is highly recommended that smoke alarms

be wired on a separate circuit ( one with no other lights or

appliances) to ensure maximum reliability of A C power supply. For

installation of smoke alarms in Dwelling Units, it is important to

follow the National Electrical Code and local codes.

1. Electricity must be turned off at service entrance before

beginning installation to prevent electrical shock or equipment

damage.

2. Location must comply with applicable buildingcodes.

3. Install a junction box where you plan to install the alarm. U se

standard 14 gauge wire.

4. C onnect black and white wires color to color from power

connector to A C power leads.

5. For multiple station application use the orange wire to

interconnect. If unit is not to be interconnected, cap unused

wire. NOT E: T he SA 360 is interconnectable with up to 11

other units.

6. Loosen or remove screws from junction box.

7. A ttach flat side of mounting plate and tighten screws to fit

snugly against the junction box and ceilingor wall.

8. Bringpower connector through center opening.

9. Slip the paper gasket supplied with the alarm over the power

connector and then onto the mounting plate so that the four

plastic tabs on the mounting plate will hold the gasket in place.

T he gasket will prevent downward air currents from entering the

smoke alarmthrough holesin the back of thealarm, unless

blocked off, downward air currents could prevent smoke from

enteringthe alarm. WARNIN G: IT IS IMPERATIVE THAT

YOU INSERT THE GASKET WHEN INSTALLING YOUR

SMOKE A LARM.

10. Align the plugarea on thesmokealarmwith the cutout in the

gasket and place the smoke alarm on the mounting plate, turn

clockwise to fasten it to the mounting plate.

11. Plugwire connector into the back of the alarm.

12. If auxiliary lock is desired, insert the LockingKey into the slot

in the base of the alarm. Locking Key should •clickŽ into

position and be flush with the alarm housing. C AU TION : Do

not attempt to remove alarm without first removing the Locking

Key. If the key is not first removed, damage may result. To

remove, use a screwdriver and gently pry theLockingKey loose.

13. Test alarmoperation after installation in accordance with

•Operation: How to TestŽinstructions.

Note: Maximum interconnect wiring length is 150 feet (50 meters).

IMPORTANT: T he SA 360 is not interconnectable with any other

model produced by another manufacturer. T he SA 360 may be

interconnected only with the following Underwriters• Laboratories

Inc. listed smoke alarm models:

American Sensors SA379

American Sensors SA360

A SI Electronics (A merican Sensors) ESA 5010/ESA 5011

Dicon Safety Products Inc. 670L/LR

Dicon Safety Products Inc. 370LBX

Note: T his equipment should be installed in accordance with the

National Fire Protection A ssociation Standard 72. (N ational Fire

Protection Association, Batterymarch Park, Quincy, MA 02269).

B. Testing After Installation

1. Check to seethat thegreen •POWER ONŽlight is on. T he

•POW ER ON Žlight is visible behind the slotted case and

confirms that the smoke alarm is receiving AC power.

2. Press and hold the test button until the alarm sounds. NOTE: It

may be necessary to press the test button for up to 20 seconds for

an alarm to sound. A n alarm is indicated by 3 loud beeps

repeating every 5 seconds. A larm may continue to sound for up

to 10 seconds after button is released.

3. A t least once a week, press the test button and hold until the

alarm sounds, then release.

NOT E: Multiple Station Only:

4. Test each alarm separately in the system.

5. Determine that the initiating alarm triggers other alarms in the

system.

7. MAINTENANCE & TROUBLESHOOTING

TEST THE ALARM W EEKLY. VACUUM EVERY SIX MONTHS.

Your smoke alarm should be cleaned every six months to help keep

the unit working efficiently. REMOV E POW ER T O A LA RM.

Gently vacuum through the vents of the alarm with a soft brush

attachment. K eep vacuum nozzle from touching the unit.

RE-ESTABLISH POWER TO ALARM.

Problems may be indicated by the following:

1. T he alarm does not sound upon pressing the test button.

2. T he green operating light does not remain steadily on when unit

is A C powered.

3. T he red operating light remains steadily on or off. ( i.e. does not

flash once every 45seconds, when the unit is not in alarm).

Try the following:

1. Inspect breaker or fuse in power circuit to alarm.

2. G ently vacuum as recommendedabove.

3. C all an electrician to inspect house wiring andconnection to

alarms.

If these procedures do not correct the problem, do NOT attempt

repairs. I f the smoke alarm is within warranty period and terms,

indicate the nature of the problem and return the unit with proof of

purchase to the point of purchase, distributor or manufacturer. See

below for instructions. Units beyond warranty cannot be

economically repaired.

FA LSE A LA RMS:

A bnormal air conditions may cause the highly sensitive smoke alarm

to give a • falseŽalarm. If no fire is apparent, ventilate the room

and/or blowfresh air into the unit until the alarm stops. Once

cleared, the smoke alarm will automatically reset.

DO NOT DISCONNECT T HE AC POWER SUPPLY.

Dust can lead to excess sensitivity. Vacuum as recommended above.

DO NOT PAINT THE UNIT.

8. LIMITED WARRANTY

Your A merican Sensors SA 360 smoke alarm is warranted for ten

years from the date of purchase against defect in material and

workmanship. Units returned to Dicon G lobal I nc.

with proof of purchase date during this period as a result of such

defects will be repaired, or replaced at Dicon G lobal Inc.s

. •option, without charge. T his warranty only covers defects in

material or workmanship in normal residential use. This warranty

does not cover damage resulting from negligent handling, misuse, or

lack of reasonable care. T his warranty is in lieu of any other

warranty either expressedor implied.

DICON GLOBAL INC. SHALL HAV E NO

LIABILITY FOR ANY PERSONAL INJURY OR PROPERTY

DA MAGE, OR ANY SPECIAL INCIDENTAL, CONTINGENT

OR CONSEQUENTIA L DA MAGE OF ANY KIND RESULT ING

FROM A FIRE. T HE EXCLUSIVE REMEDY FOR BREA CH OF

THE LIMIT ED WA RRANTY CONTAINED HEREIN IS THE

REPAIR OR REPLACEMENT OF T HE DEFECTIVE PRODUCT

AT DICON GLOBA L INC.S OPTION IN NO

CASE SHALL DICON GLOBAL INC.S

LIABILITY UNDER A NY OT HER REMEDY PRESCRIBED BY

120 VAC -IONIZA TION

SMOKE ALARM

READ CAREFULLY AND SAVE.

T his manual contains important information.

A copy of this manual must be left withthe end user.

2502-2509 (REV-1)

LAW EXCEED THE PURCHASE PRICE. YOUR SMOKE

ALA RM IS NOT A SUBSTITUT E FOR PROPERTY,

DISABILITY, LIFE OR OTHER INSURANCE OF ANY KIND.

APPROPRIATE COVERA GE IS YOUR RESPONSIBILIT Y.

CONSULT YOUR INSURANCE AGENT.

T his warranty gives you specific legal rights and you may have other

rights which may vary from state to state.

U nits may be returned to point of purchase according to

retailers exchange / return policy. Or call 1-800-387-4219, for

shipping instructions and a returned goods authorization number

•RGA Žnumber, to return to Dicon Global Inc.

Returned goods must be shipped prepaid. A cheque for $5.00 is

also requiredfor return postage

. Please mark the •R GA Žnumber

on the exterior of your package. Date code located on back of smoke

alarm.

Dicon Global Inc.

20 S teelcase R oad, Unit 3

Markham, Ontario,

Canada L3R 1B2

9. AMERICAN SENSORS PRODUCTS

A merican Sensors offers a complete line of smoke alarms. Select

from this group of quality products to ensure your home is fully

protected in case of fire.

WAR NING

Smoke alarm

paper gasket (not shown-fits in between)

mounting plate

quick disconnect

power connector

BLAC K 120VAC , 60Hz

WHITE

Cap Unused Wire

Twis t Conne ctors

Ceiling

Mounting Plate

S upplied Ga sket M ust B e

Installed In Mounting Plate

Quick Disconnect

P ower C onnector

BLAC K 120VAC , 60Hz

WHITE

OR ANG E Interconnect

MODEL SA360

120VAC Dual-Ionization

Interconnectable

Smoke A larm

MULTIPLE STATION

Smoke Alarm

Outlet B ox

SINGLE STATION

MODEL

SA360

To Use Optional Locking Key-

R emove from mounting plate with needle nosed pliers and insert in housing

Dining Kitchen Be droom Bedroom

Bedroom

Living R oom

Bedroom

Kitchen

Dining

Living R oom

TV R oom

Kitchen

Living

Room

BedroomBedroom

Basement

Hall

Furnace

Figure 1 Figure 2

Figure 3

Smoke alarms for limited protection

Additional smoke alarms for better coverage

T hese diagrams show smoke alarm

locations as recommended.

WAR NING

AMERICAN SENSORS

CAR BON MON OXIDE ALARMS

American Sensors alsooffersacompleteline ofCarbon Monoxide

Alarms including:

CO800 - Plug-In Carbon MonoxideAlarm

CO810 - 120 Volt A C Hardwire Carbon MonoxideAlarm

CO900 - Plug-In Carbon MonoxideAlarmwith Battery Back-

CO910 - Plug-In Carbon MonoxideAlarmwith Digital LED

Display

CO920 - Plug-In Carbon MonoxideAlarmwith Digital LED

andBack-UpPower Source

CO1100 - Battery Powered Carbon Monoxide Alarm for Table

Top, Travel or Wall Mount

Model

SA 310

SA 320

SA 358

SA 500

SA 900

SA 360

SA 379

Description

Basic Model

General Purpose

Model

with Alarm-Pause

Feature

Hall and Stairways M odel

with Emergency Light

ExtendedLife

Multi-Location with

Alarm-Pause®Model

LongLife Multi-

Location with

Alarm-Pause®Model

Professional Hardwire

Multi-Location Model

Professional Hardwire

with Battery Back-Up

andAlarm-Pause®

Model

Power Source

9V Battery

2-9V Batteries

ExtendedLife

Battery with

3 Year Warranty

LongLife Lithium

battery with 10

year warranty

120 Volt A C

120 Volt A C with

9 Volt Back-Up

Battery

Smoke A larm

Technology

Ionization

AMERICAN SENSORS SMOKE A LARMS