American Standard COPELAND 7005.900 User manual

*Wrench
Certified to comply with ANSI A112.18.1M
Recommended Tools
*Supplied with Fitting
*Hex key
SPOUT RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
12
Assemble RUBBER WASHER (4) and BRASS WASHER (5) and
LOCKNUT (6) onto SPOUT SHANK (3). Align SPOUT ASSEMBLY
and from underside of ledge secure SPOUT ASSEMBLY into
position with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
4
2
3
1
3
4
1
2
4
5
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
ADJ. 6-1/2 TO 12
6
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
MOUNTING
SURFACE
VALVE inlet is 3/4-inch NPT male.
NOTE
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
7"
DECK-MOUNT BATH FILLER
Installation
Instructions
7005.900
7005.901
1-1/2 MAX.
1-1/4
MAX.
1-3/16 DIA.
3
(H)(C)
1-1/8 DIA.
8-3/16
12 MAX
2-1/16
DIA.
1-1/16 DIA.
3/4-14 MALE
N.P.T. INLETS
Install RING WASHER (1) into SPOUT recess. Check that O-RING (2)
on end of SPOUT SHANK (3) is in place. Insert SPOUT SHANK (3)
through center hole on mounting surface.
COPELAND
4-1/8"
2"
9-3/8"
2-1/4"
2-3/4"
3
M968638 REV.1.1
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
SPOUT
ASSEMBLY
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

5SERVICE
9
2
4
5/16'' MIN. MOUNTING
SURFACE
FOR FITTING
LESS SPRAY
10
11
11
10
1
3
4
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and
attach to SPOUT SHANK (6) and tighten. For 7005.901 use a 10 mm
(3/8") hex key.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
12 13
7
6
8
8a
5
13
12
3
4
MOUNTING
SURFACE
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
M968638 REV.1.1
INSTALL HANDLES
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. Fig. A. Tighten
STEM SCREW (3) to secure ADAPTER (1).
Align HANDLE BASE (4) and push onto HANDLE ADAPTER (5) until flush
against mounting surface.
Find correct position of LEVER HANDLE (6) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (6).
Tighten SET SCREW (7) with 5/64"HEX WRENCH (8) SUPPLIED.
1
4
2
5
TOP
SPLINE END DOWN
Fig. A.
3
87
6
5/64" HEX
WRENCH
To change direction of handle:
2
90˚
If spout drips, operate handles several times from
OFF to ON position. Do not force - handles turn only 90˚.
6
4
3
5
7
1
Turn valve to OFF position
Remove SET SCREW (7) with 5/64" Hex Wrench.
Pull HANDLE (1) “UP” firmly to release from
ADAPTER (3).
Pull HANDLE BASE (6) off DECK ADAPTER (2).
Remove SPRING CLIP (4). Lift STOP WASHER (5),
turn 90˚ and replace. Replace SPRING CLIP (4).
Re-install HANDLE ASSEMBLY.

9
HANDSHOWER INSTALLATION
(FOR MODEL 7005.901 ONLY)
TEST INSTALLED FAUCET
7
Turn VALVES (1) to "off" position.
Lift HANDSHOWER (3) from holder, direct spray into tub, lift
TRANSFER KNOB (4) to check HANDSHOWER (3) and HOSES for leaks.
Turn VALVES "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and ESCUTCHEON (1). ( Note: SPRAY HOLDER (6)
must be separate from ESCUTCHEON (1) to get HOSE (8)
thrrough ESCUTCHEON (1).] Install SEAL (9) and connect both
HOSES (8) and (10). INSTALL second SEAL (9) and connect
HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
6
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT (2) mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
7
8
10
9
9
11
6
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2007
1
4
1
3
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
2
M968638 REV.1.1
IN MEXICO 01-800-839-12-00
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
8
Hex wench, supplied
To remove handles, reverse steps in STEP 4.
To remove SPOUT (1), proceed as follows:
Lift KNOB (2) and unscrew from TRANSFER ROD (7).
Remove SET SCREW (3) using 5 mm hex wrench supplied.
Lift SPOUT (1) off SHANK (4) carefully and remove RUBBER
RING (5).
Unscrew SHANK SLEEVE (6) and lift TRANSFER ROD (7) from
SHANK (4).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (5) is properly seated in its recess at the base of SPOUT (1).
Make certain SET SCREW (3) is properly aligned and tight so that
SPOUT (1) is locked in place.
3
7
5
4
6
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.
DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
CARE INSTRUCTIONS: