American Standard Codie Installation instructions

Rev. A0 - 1 -
- 4 -
FFASB221-609500BF0
In-Wall Bath & Shower Mixing Valve
FFASB221-609500BF0 FFASB222-709500BF0
FFASB222-709500BF0
In-Wall Shower Only Mixing Valve
21
42
46~56
184
65
11
24.5
134
G 3/4”
G 1/2”
G 1/2” 184
30~38 11
24.5
42
124
G 1/2”
G 1/2”
75
119
70
55
9
7
8
7
3
4
6
5
A
B
Codie
Codie
FFASB221-609500BF0 FFASB222-709500BF0
Unit：mm
Care & Maintenance
* If you want to do the maintenance
for the faucet, please follow the
below process.
Attention:
Please Leave the manual with the customer
after installation is finished.
1
2
Test / Usage
* Move handle down into “OFF”position. Turn on supply angle valve to check allconnections for leak.
* Operate handle up and down, left and right to flush water lines thoroughly.
Test
Usage
Trouble Shooting Guide
Untwist the hose.
Cartridge packing
Hose junction Check the connection.
Check cartridge install.
Check valve position.
Check any impurities. Remove all impurities.
Open it to full valve
When packing is damaged, replace the cartridge.
Check the existence of packing and wind it up sufficiently
Poor flow rate
Leakage
Angle valve
Flexible hose
Regulator
Check if hose is twisted.
Check if the water from Supply valve is enough or not
Check if the supply pipe connected correct or not Connect the hot and cold water pipe correctly
Increase water supply
Deviant
Temperature
Supply Valve
Trouble
Checkpoint
Contents Action
Supply system
(Cold)
ON
(Hot)
Dimension
Installation &
Operation Instructions
* Recommended water pressure condition: 0.1~0.5Mpa.
* Environment Temperature:1~55℃
* Steam is not allowed to use.
* The cold and hot water pipes must not be reserved.
Conditions for use
*Remove all impurity in pipes before beginning to avoid clogging. Connect faucet pipes correctly.
* Check installation distances in the Dimension diagram to ensure correct installation.
Make sure the cold water hose is connected to the right side and the hot water hose to the left.
When in the process of installation, grab the whole body. Do not grab handle only.
Pre-Installation Checks
* American Standard always keep raising and improving the product design and performance, and reserve the right to modify
the dimension and spefication. At this case, we will not inform you separately.
* This installation instruction sheet is for your reference only, the dimension and specification is subject to the actual products.
Thank you for selecting American-Standard - the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
All instruction procedures must comply in strict accordance with applicable local plumbing and building codes
Recommended Tools and Materials
Pencil
Windtight S wathe
Adjustabl e Wrench Level Tape Measure
Screwdriv er
Connect to Shower
Connect to Spout
The inner diameter of pipe from
body to spout (including connector)
need to be more than 13mm
!
Connect to Shower
Wall
Wall

- 2 - - 3 -
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Body
Washer
Escutcheon
Screw
Cap
Diverter Valve
Pipe
Cartridge
Nut
Cap
Handle
Screw
Index Button
Body
Washer
Escutcheon
Cover
Cover
In-hex Wrench
1
1
1
2
2
1
1
1
1
1
1
1
1
0
0
0
1
0
1
3
5
4
6
123
456
7
8910 11
12
13
14 15 16
17
18
19
0
0
0
2
2
0
1
1
1
1
1
1
1
1
1
1
0
1
1
1
2
7
8
9
FFASB221 / FFASB222
Installing the Body
1
Installation
* Consult the dimension drawing and lay the pipes.
* Before installation, Wash and clean the water supply pipes.
Body C over
Body Co ve er
* Finishing wall should be between the minimum
and the maximum.
Body Co ve r
8mm
Wall (Max.)
Wall (Min.)
10mm
Wall Connect the Water Supply Pipe(Shower)
Connect the Water Supply Pipe
(Spout)
Connect the Water
Supply Pipe(Cold)
Connect the Water
Supply Pipe
(Hot) Wall (Max.)
Wall (Min.)
2
3
Finish Wall
Installing the Escutcheon & Handle
* confirm there is no leakage in every connection.
* Finish the Wall
Parts List
No. Part Name Q ’ty
Parts List