American Standard 1662SG.211 User manual

Certified to comply with ANSI A112.18.1
Recommended Tools & Materials
ROUGHING-IN DIMENSIONS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
M965666 Rev. 1.0 (1/17)
Electric Drill
To r c h
6mm (15/64")
Drill Bit
Pencil
Phillips Screwdriver Hammer
COMMERCIAL SHOWER
SYSTEM KITS: 1.5 gpm & 2.5 gpm
BOTTOM OF SHOWER
1-5/8" TO 3-1/4"
12"
OPTIONAL
OPTIONAL
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 48" TO 54"
1/2" SUPPLIES
PLUG TUB
OUTLET
6" DIA.
FINISHED WALL
8"
Universal Inlets / Outlets:
1/2" NOM Copper Sweat or 1/2" NPT
5-7/8"
1-1/4"
1/2"
1/2" NPT
Adjustable Wrench
10'
Pipe Wrench Tubing Cutter
Tape
Measure
Sealing Tape
1660766.002
(1.5 gpm)
1660767.002
(2.5 gpm)
Installation must conform to all local building codes.
3-5/16"
8-1/8"
1/2" NPSM
48"
1-5/8"
36"
37-1/2"
FINISHED
WALL
3-1/8" DIA.
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
36" 60"
TO
3-1/8" DIA.
3-1/8" DIA.
Installation
Instructions
1662SG.211
1662SG.221
1662SG.211 (1.5gpm)
1662SG.221 (2.5gpm)

M965666 Rev. 1.0 (1/17)
INSTALL WALL SUPPLY
1/2" NPT
APPLY SEALANT
OR SEALING TAPE
Supply to WALL SUPPLY is 1/2" NPT. See rough-in above for detailed information.
Apply sealant or sealing tape to threads of 1/2" NPT supply nipple.
1
When finished tiling the wall, remove PLASTER GUARD.
Install VALVE TRIM.
REFER TO INSTALLATION INSTRUCTIONS (M968637) SUPPLIED WITH WALL
SUPPLY FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
REFER TO INSTALLATION INSTRUCTIONS (M968763) SUPPLIED WITH VALVE
TRIM KIT FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
NOTE
NOTE
MAKE ALL CONCEALED PIPING CONNECTIONS
INSTALL VALVE TRIM
2
3
See Roughing-in diagram before starting.
Make Hot and Cold supply connections to the VALVE BODY. Inlet and outlet connections to the valve body are 1/2" copper sweat.
Make the connections for the HAND SHOWER. The HAND SHOWER connection is 1/2" NPT.
For support, use PIPE BRACES secured to wooden braces. Cap off HAND SHOWER. With the R120SS VALVE turned off, turn
on water supplies. Check for leaks.
Finish all wall construction.
4
PLASTER GUARD
1/2" SWEAT PLUG
INSTALL THE R121SS VALVE BODY
R121SS
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS
(IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops
(if present) and plaster guard to continue installation. Use thread sealant or Teflon tape
on threaded connections.
NOTE
IMPORTANT
See Roughing-in diagram before starting.
Connections are:
1/2" NOM Copper Sweat or 1/2" NPT inlets
1/2" NOM Copper Sweat or 1/2" NPT tub and shower outlets
REFER TO INSTALLATION INSTRUCTIONS (M965661) SUPPLIED WITH VALVE BODY FOR
COMPLETE INSTALLATION AND REPAIR PART INFORMATION.

M965666 Rev. 1.0 (1/17)
5INSTALLATION INSTRUCTIONS
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
FINISHED
FLOOR
915mm
(36")
1525mm
(60")
TO
914mm
(36")
The GRAB BAR (1) works best when secured to the wall studs or cross brace using WOOD SCREWS. If mounting
into the studs is not possible, use appropriate wall fasteners provided to secure the installation.
Mark a vertical center line in the location you wish to install the SLIDE BAR (1). NOTE: The height from the finished floor
is optional. See rough-in drawing for suggested dimensions.
Determine desired height from the finished floor to the lower support and mark a horizontal center line. Slide the two
WALL ESCUTCHEONS (5) away from the MOUNTING FLANGES (3). Position the GRAB BAR (1) as shown in Fig. A and
mark the location of the six mounting holes to be drilled. Fig. A. Using a #10 masonry drill, drill six mounting holes
1-1/4" max. deep. Fig. B.
Install the six ANCHORS (2) provided into the mounting holes. Use a hammer to lightly tap ANCHORS (2) into place.
Make sure they are installed flush against the finished wall. Fig. B.
Align and place the GRAB BAR MOUNTING FLANGES (3) over the installed ANCHORS (2). Secure the GRAB BAR (1)
to the wall with the SCREWS (4) provided. Fig. B.
Push WALL ESCUTCHEONS (5) against finished wall. Rotate WALL ESCUTCHEONS (5) clockwise to lock into
position. Fig. C.
Check operation of SLIDE BAR (1) by rotating HOLDER LEVER (7) and moving HAND SHOWER HOLDER (9) up and down.
Rotate LEVER HANDLE (7) back to lock HAND SHOWER HOLDER (6). Fig. B.
2
LEVEL
VERTICAL
CENTER LINE
DRILLED
MOUNTING
HOLES
R OTAT E
CLOCKWISE
TO LOCK
LOCK
UNLOCK
LARGE
DIAMETER UP
C/L
6
1 1
1
8
7
3
4
5
5
5
Fig. A Fig. B Fig. C
Make sure larger diameter side of SPRAY HOLDER (6) is facing upward. If not rotate SPRAY HOLDER (6) 180 dergees.
Rotate the LEVER HANDLE (7) to the unlocked position. Push the SPRAY HOLDER (6) side onto the GRAB BAR (1).
Push the LEVER HANDLE SIDE (7) over the SPRAY HOLDER ARMS (8) until the two snap togerther.

HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2017 M965666 Rev. 1.0 (1/17)
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
MODEL NUMBER
T675.500
MODEL NUMBER
R121SS
M952100-0070A
PRESSURE BALANCING UNI
023529-0070A
CARTRIDG
023603-0070A
CARTRIDGE SCREWS
051122-0070A
SCREWDRIVER STOPS
050145-0070A
1/2" SWEAT PLUG
PRESSURE BALANCE
TEMPERATURE/VOLUME
CONTROL VALVE
COLONY SOFT
VALVE TRIM
M961854-0070A
FIXATION RING WITH SCREWS
M961856-0020A
ESCUTCHEON AND SCREWS
078016-0020A
ESCUTCHEON SCREWS
M909606-0020A
DECAL
M907050-0020A
ESCUTCHEON CAP SET
M961636-0020A
LEVER HANDLE KIT
030126-0070A
HANDLE SCREW KIT
013205-0070A
STOP VALVE O-RING
INSTALL HOSE AND HAND SHOWER
TEST SHOWER SYSTEM
6
Turn on water supplies and check all fuctions of of the SHOWER
SYSTEM KIT. Check for any leaks.
Install SEAL (1) into COUPLING NUT (2). Connect COUPLING NUT (2)
to WALL SUPPLY NIPPLE (3) and tighten.
INSTALL second SEAL (4) into SPRAY HOSE END (5) and connect
HAND SHOWER (6) to SPRAY HOSE END (5). Hand tighten. 6
4
5
1
3
2
CHROME 002
Appropriate finish code

HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2017 M965666 Rev. 1.0 (1/17)
8888.037.002
WALL SUPPLY
8888.035.002
METAL HOSE
1660.236.002
36" SLIDE BAR
8888037.002
WALL SUPPLY
030782-0020A
HOSE KIT
M962520-0020A
CHECK VALVE
3-FUNCTION HAND
SHOWER
1660766.002
(1.5 gpm)
1660767.002
(2.5 gpm)
M9641800020A
SPRAY HOLDER
ASSEMBLY
M964179-0070A
MOUNTING KIT
CHROME 002
Appropriate finish code