American Standard Evolution ASTM E162 User manual

G37
© 2008 AS America Inc.
SILHOUETTE™ 18" ISLAND SINK
• Americast® brand engineered material
• Single bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 1 or 3 faucet hole conguration
• Customized hole punchings available
(see page G56)
Top Mount/Undercounter:
❏ 7185.001 Center hole only
❏ 7185.803 3 hole
Under Counter Installation Order:
❏ 791326-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
457 x 457 x 216mm
(18" x 18" x 8-1/2")
Bowl sizes:
375mm (14-3/4") wide
375mm (14-3/4") front to back
203mm (8") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Trap:
Optional Accessories:
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
SILHOUETTE™ 18"
ISLAND SINK
AMERICAST®
Revised 2/08
Top Mount Installation (faucet not included)
Undercounter Mount Installation
(faucet not included)
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G38
© 2008 AS America Inc.
7185.803/823 Top Mount
Undercounter Mount
NOTES:
* TOP MOUNT (7185.803): COUNTERTOP CUTOUT
425mm x 425mm WITH 25mm RADIUS (16-3/4 X 16-3/4 WITH 1" RAD.)
AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
C/L
FINISHED WALL
OR SPLASHBACK
*CUTOUT NOTE
SEALING COMPOUND
FINISHED FLOOR
COUNTERTOP
(BY OTHERS)
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
1/2"
(13mm)
5-3/4"
(146mm)
9-1/8"
(232mm)
18"
(457mm)
18"
(457mm)
9"
(229mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
DIA. HOLES TYP.
2" (51mm)
OPTIONAL
7-3/8"
(187mm)
2"
(51mm)
2"
(51mm) 2"
(51mm)
4-5/8"
(117mm)
2-5/8"
(67mm)
C/L
FINISHED WALL
OR SPLASHBACK
* CUTOUT NOTE
COUNTERTOP
(BY OTHERS)
SEALING COMPOUND
FINISHED FLOOR
DETAIL OF MOUNTING CLIP
(KIT No.791003-100)
BRASS INSERT
1/2" (13mm) MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
MOUNTING CLIP
(SEE DETAIL)
18"
(457mm)
1-1/2" (38mm)
DIA. HOLES TYP.
2" (51mm)
OPTIONAL
7-3/8"
(187mm)
2" (51mm)
4-5/8"
(117mm)
2-5/8"
(67mm)
18"
(457mm)
9"
(229mm)
3-1/2"
(89mm)
DIA.
1-1/2"
(38mm)
DIA.
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
5-3/4"
(146mm)
9"
(229mm)
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR
EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK
COUNTERTOP CUTOUT VARIATIONS.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
SILHOUETTE™ 18"
ISLAND SINK
AMERICAST®
Revised 2/08