American Standard Studio-S 4803300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2019
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M985011 (3/19)
INSTALL FAUCET
Studio-S®
Pull-Down Kitchen Faucet
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver
Certied to comply with ANSI A112.18.1M
INSTALLATION
INSTRUCTIONS
4803300
Certied to comply with ANSI A112.18.1M
SPOUT BASE
1
4
3
2
5
6
8
7
2
• Make certain the SEAL (1) is properly seated in recess of
spout base.
• Insert all HOSES (2) and SHANK (3) through MOUNTING
RING (4) and mounting surface. Do not use putty.
• Insert HOSES (2) through RUBBER WASHER (5), BRASS
WASHER (6), and threaded LOCKNUT (7).
• Assemble RUBBER WASHER (5), BRASS WASHER (6), and
threaded LOCKNUT (7) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7).
• Use a screwdriver to tighten SCREWS (8) on LOCKNUT (7).
Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
CAUTION Turn off water at
main supply

- 2 -
2
M985011 (3/19)
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 32 "long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
3
4
5
STREAM (AERATOR)
SPRAY
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
2
3
1
REMOVE
COLD
ON
OFF HOT
7
6
8
2
1
3
4
5
• Push the SPRAY HOSE END (1) into the HOSE
CONNECTOR (2) and slide down the LOCKING
COLLAR (3) until it snaps into place.
• With HAND SPRAY (4) seated in SPOUT (5), install
WEIGHT (6) at labeled area on HOSE (7), secure
with SCREW (8).
4TEST INSTALLED FAUCET
• Turn ON water at main supply.
• With HANDLE (1) in “off” position, unthread SPRAY (3) from HOSE (2).
• Operate handle back to front, in COLD and HOT positions, to ush water
lines thoroughly.
• Replace SPRAY (3) onto HOSE (2).
SPRAY OPERATION
• With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch
from stream to spray.
• Press and hold PAUSE BUTTON (5) to temporarily stop ow from SPRAY
(3). Release PAUSE BUTTON (5) to resume ow from SPRAY (3).

- 3 -
6SERVICE
5
M985011 (3/19)
• Move HANDLE into “off” position.
• Turn on water supplies and check connections for leaks.
• Operate HANDLE up and down, left and right to ush
water lines thoroughly.
• Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS FOR LEAKS
CHECK CONNECTIONS
FOR LEAKS
2
1
3
5
5a
4
6
7
7
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
If Faucet Drips, Proceed As Follows:
• Turn VALVE to OFF position.
• Operate HANDLE several times from OFF to ON position. Do not apply excessive force.
Reduced Flow:
• Clean out spray head screen.
• Clean out cartridge.
Clogged CARTRIDGE outlets or inlets may
cause reduced flow.
To clean, rst turn off water supply then:
• Loosen HANDLE SCREW (1) and remove
HANDLE (2).
• Unthread ESCUTCHEON CAP (3),
SNAP RING (4).
• Lift CARTRIDGE (5) off MANIFOLD (6) and
remove CARTRIDGE SEALS (7).
• Clean MANIFOLD (6), CARTRIDGE (5)
ports and SEALS (7).
• Place SEALS (7) into CARTRIDGE
PORTS (5a).
• Place CARTRIDGE (5) onto MANIFOLD (6).
• Replace ESCUTCHEON CAP (3), SNAP RING (4),
HANDLE (2), tighten HANDLE
SCREW (1).