American Standard PINE 2011.101 User manual

Certified to comply with ANSI A112.18.1
Installation
Instructions
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
2011.101
PINE
M965246 REV. 1.6
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
™
Monoblock Bathroom Sink Faucet
with Conventional Pop-up Drain
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
8
4
1
2
1INSTALL FAUCET Turn off hot and cold water
supplies before beginning.
CAUTION
GROOVE
(FAUCET
BASE)
MOUNTING SURFACE
Seat SEAL (1) into under side of FAUCET BASE (2). Fig. A.
Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and LIFT ROD (8)
through the mounting hole of lavatory or mounting surface. Fig. A.
From below, push GASKET (7) with RETAINING WASHER (5) onto
MOUNTING STUD (4). Install MOUNTING NUT (6)
onto MOUNTING STUD (4). Fig. B.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting.
Fig. A.
Fig. B.
6
4
7
5
3

PUTTY
M965246 REV. 1.6
2
3
INSTALL POP-UP DRAIN
ASSEMBLE PIVOT ROD TO POP-UP DRAIN
Fig.1 Fig.1 Fig.2
Fig.3
Fig.2
Fig.3
11
3
4
2
5
9
8
7
6
10
6
5
8
7
3
2
4
1
Apply a bead of putty to underside
of FLANGE (1).
Drop FLANGE (1) into LAVATORY DRAIN (2).
From below assemble RUBBER GASKET (3), METAL
WASHER (4) and LOCK NUT (5). Do not tighten.
Place SEAL (6) with small end facing up into
TAILPIECE (7) and tighten against DRAIN BODY (8).
PIVOT ROD (9) opening in TAILPIECE (7) should face
the rear of the lavatory.
Tighten LOCK NUT (10) with channel locks.
Do not over tighten.
Adjust STOPPER (5) height by repositioning EXTENSION (7) and
tightening THUMBSCREW (8).
Insert PIVOT ROD (1) into second or third hole in EXTENSION (7)
and reassemble CLIP (3). (EXTENSION (7) may need to be bent).
Remove one end of CLIP (3) from PIVOT ROD (1) by squeezing
ends together while sliding.
Assemble PIVOT ROD (1), PIVOT NUT (2), CLIP (3) and SEAL (4) as
shown. Hand tighten PIVOT NUT (2). Drop STOPPER (5) into drain.
(For vandal proof drain rotate stopper so PIVOT ROD (1) goes
through EYE (6) of STOPPER (5). Make connection to "P" TRAP.)
“P” TRAP
1-1/4" OD
TAILPIECE

Operate POP-UP KNOB (4) and fill lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, adjust POP-UP ROD (6).
Release POP-UP KNOB (4) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
MAKE WATER SUPPLY AND WASTE CONNECTIONS
4
5
1
APPROX. 508mm"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on fitting supplies are 3/8" compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Band) and right supply
to COLD (2) wall supply.
Faucet supplies are 508mm" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
1
M965246 REV. 1.6
2
TEST INSTALLED FITTING
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to flush water lines thoroughly.
Replace AERATOR (3).
5
4
2
CHECK DRAIN CONNECTIONS
“P” TRAP
WASTE
OUTLET
3
6
1
1
OFF
ON
COLD
HOT
2.5mm HEX KEY
REMOVE INSTALL
6SERVICE
To remove or replace cartidge:
Turn valve to OFF position.
Pull out PLUG BUTTON (1) and loosen HANDLE SCREW (2).
Pull off HANDLE (3) and unthread CAP (4).
Unthread CARTRIDGE NUT (5) and remove.
Pull out CARTRIDGE (6).
Inspect CARTRIDGE (6) and O-RINGS (7) for debris and
clean if necessary.
Clean MANIFOLD (8) and rinse clean.
Reinstall CARTRIDGE (6) and O-RINGS (7) onto CARTRIDGE (6).
Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3).
If spout drips, operate handle several times from OFF to ON and
HOT to COLD position. Do not force handle.
AERATOR (9) and HOSE FILTER SCREENS (10) may accumulate
debris causing distorted or reduced water flow. Remove AERATOR
(9) and/or water supplies and rinse clean.
Turn off hot and cold water
supplies before beginning.
CAUTION
4
5
6
7
3
2
8
9
10

M965246 REV. 1.6
Monoblock Bathroom Sink Faucet
with Conventional Pop-up Drain
MODEL NUMBER
2011.101
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
IN MEXICO 01-800-839-1200
M964185-0020A
POP-UP ROD
M964183-0020A
CARTRIDGE COVER
M964318-0020A
HANDLE KIT
2.5mm HEX KEY
M964224-0070A
MOUNTING KIT
© AS America, Inc. 2012
M962682-0070A
CARTRIDGE
PINE™
CHROME 002
Appropriate finish code
M964228-0020A
AERATOR
M953465-0020A
DRAIN ASSEMBLY
M964328-0020A
HANDLE KIT