American Standard Innsbrook SELECTRONIC 605 202 Series User manual

1M965652 Rev. 1.9 (3/19)
© 2019 AS America Inc.
Installation Instructions
SELECTRONIC®
Innsbrook Lavatory Proximity Faucet
MODEL NUMBERS
605X.202
605X.204
605X.205
Certied to comply with:
• ASME A112.18.1
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
Product No.’s & Options 1
Specications 2
Faucet Installation 2-3
Electrical Installation 4-6
Start-up / Maintenance 7-8
FAQ’s / Troubleshooting 9-10
Parts 11
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.

2M965652 Rev. 1.9 (3/19)
Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
The illustration below shows the tting and all loose items after they have been removed
from the carton. Some items may be packaged partially assembled to other items.
UNPACKING All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping
1. Installation Instructions
2. Spout Assembly
3. Mounting Nuts
4. Control Box
5. Supply Hose
6. Mixing Valve (optional, must be ordered separately)
7. Control Box Cover Screws
605XTMV
6059.202
6059.205
PRODUCT No.s
2
4
3
6
5
Mixing ValveBase Product
DO NOT REMOVE
PROTECTIVE
FILM FROM
SENSOR EYE UNTIL
INSTALLATION IS
COMPLETE.
1
Installation Instructions
SELECTRONIC®
Hard-Wired ACPowered Innsbrook
Lavatory Proximity Faucet
MODEL NUMBERS
605X.202
605X.204
605X.205
•
ASMEA112.18.1
NOTETO INSTALLER: Please givethis manual to the customer after installation.
Tolearn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at:[email protected]
ForParts, Ser vice,Warranty or other Assistance,
please call (844) CRT-TEAM/ [phone] (In Canada:1-800-387-0369)
(InToronto Area only: 1-905-306-1093)
Product No.’s& Options 1
2
Faucet Installation 2-3
Electrical Installation 4-6
Start-up / Maintenance 7-8
FAQ’s/ Troubleshooting 9-10
Parts 11
CAUTION: Use only American Standard
suppliedcable sets. Using non-AS supplied
cables,or cutting, splicing or modifying any
componentswill void the warranty.
7
Plug-In AC
Power Kit
Hard-Wired AC
Power Kit
Multi-AC
Power Kit
PK00.PAC PK00.HAC PK00.MAC
POWER KITS SOLD SEPARATELY

3M965652 Rev. 1.9 (3/19)
Fig. 1a
1
5
2
4
3
3
SENSOR
CABLES
6
6
5
5
Fig. 1b
Fig. 2
12
3
4
5
6
7
10'
Roughing-in Dimensions
Fig. 1
RECOMMENDED TOOLS
1. Slip Joint Pliers
2. Adjustable Wrench
3. Plumbers’ Putty or Caulking
4. Phillips Screwdriver
5. Flat Blade Screwdriver
6. Electric Drill & 1/4" Drill Bit
7. Tape Measure
1. Installation Instructions
2. Spout Assembly
3. Mounting Nuts
4. Control Box
5. Supply Hose
6. Mixing Valve (optional, must be ordered separately)
7. Control Box Cover Screws
GENERAL DESCRIPTION
Electronic faucet with proximity operation. Vandal
resistant solid brass construction single post mounting.
Operates on DC (battery/power pack) or AC permanent
power (plug-in/hardwire). In-line strainer for solenoid
is integral. Single inlet 3/8 compression, built-in check
valves, and exible stainless steel 16-1/4" reach inlet
hose for spout connection.
Note: All plumbing and electrical wiring must be
installed in accordance with applicable codes,
regulations and standards.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
1
INSTALL SPOUT ASSEMBLY;Fig. 1
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert CABLES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From underside of mounting surface, install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
CAUTION Turn off hot and cold water
supplies before beginning.
FAUCET INSTALLATION
381mm
(15)
155mm
(6-1/8)
102mm
(4)
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
114mm
(4-1/2)
500mm
(20")
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
MOUNTING
SURFACE
FINISHED
WALL
175mm
(6-7/8)
162mm
(6-3/8)
35mm
(1-3/8)
DIA.
3 HOLES
108mm
(4-1/4)
57mm
(2-1/4)
RECOMENDED ELECTRICAL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AND MULTI AC 10’ MAX. CABLE LENGTH
4"(102mm) SQ. X 3-1/2"(89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).

4M965652 Rev. 1.9 (3/19)
2MOUNT CONTROL BOX; Fig. 2
1. Determine location of CONTROL BOX (1). It must be located
with-in the 14" (356mm) by 21" (533mm) shaded area shown
in Figure 2 in order for electrical connections from the spout
assembly to be made.
NOTE: CONTROL BOX SUPPLY HOSE IS 20".DISTANCE
BETWEEN WALL SUPPLY AND ENCLOSURE (1)
MUST BE TAKEN INTO CONSIDERATION.
2. Remove tape from CONTROL BOX COVER (2) and pull off
COVER (2). Hold the CONTROL BOX (1) in desired
location and mark the four mounting hole locations as
shown.
NOTE: Find plastic bag containing 4 M5X16 screws to be
used for securing the CONTROL BOX COVER (1)
when installation is complete.
NOTE: For AC installation, make power supply connection
before mounting CONTROL BOX (1) to wall.
3. It is recommended that the CONTROL BOX (1) be
secured to a wall stud or cross brace within the wall using
the SCREWS (3) supplied. If the CONTROL BOX (1) is to
be installed on tile or plaster walls, the ANCHORS (4) and
SCREWS (3) should be used.
3
CONNECT SPOUT HOSE TO CONTROL BOX;
Fig. 3
1. Connect SUPPLY NUT (1) from spout hose to nipple on top
of ENCLOSURE (2). Tighten with adjustable wrench to make
a water tight connection. Fig. 3.
4CONNECT WATER SUPPLY TO CONTROL
BOX AND WALL SUPPLY; Fig. 4, 4a
NOTE: If using the optional Mixing Valve, see sheet
#M968808 for installation instructions.
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
CONTROL BOX (2).
2. Connect FLEXIBLE SUPPLY HOSE (3) to SUPPLY NUT (1)
on CONTROL BOX (2). Tighten to make a water tight
connection. Use two wrenches to tighten if necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY HOSE (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY HOSE (3) is 3/8"
compression. Use adjustable wrench to tighten connection.
Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY HOSE (3) measures 20" from
the bottom of the CONTROL BOX (2) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY HOSE (3) is too long, loop to
avoid kinking.
Fig. 2
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
Fig. 3 1
2
1
3
3
Fig. 4
2
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4

5M965652 Rev. 1.9 (3/19)
ADC VERSIONS ; Fig. 1
• PWRX
•STANDARD BATTERY
1. Remove CONTROL BOX COVER (1). Fig. 1.
2. Feed the CABLES (2) through the top of CONTROL BOX
(3). Fig. 1a.
FOR STANDARD BATTERY VERSION ONLY
3. Insert BATTERY (4) into BATTERY HOLDER (5),
make sure the shape of the BATTERY (4) follows the
shape of the BATTERY HOLDER (5) and terminal end
is inserted rst. Fig. 1b.
4. Insert the BATTERY CONNECTOR (5a) from the
Standard Battery or PWRX Battery Pack through side
GROMMET (6) as shown. Fig. 1c.
5. Connect SOLENOID CABLE (7) and BATTERY
CONNECTOR (5a) to CABLES (2). Place Standard
Battery or PWRX Battery Pack into housing. Fig. 1d.
6. Reinstall CONTROL BOX COVER (1). Tighten cover
screws rmly.
Fig. 1a Fig. 1b
Fig. 1
2
3
1
4
5
INSTALL BATTERY
CR-P2
5a
5
Fig. 1c
7
2
STANDARD
BATTERY
PWRX
5a
5a
6
STANDARD
BATTERY
PWRX
Fig. 1d 5a
CAUTION: Use only American Standard supplied cable sets.
Using non-AS supplied cables, or cutting, splicing or modifying
any components will void the warranty.
ELECTRICAL INSTALLATION
Product Page
Plug-In AC Power Kit (PK00.PAC) 6
Hard-Wired AC Power Kit (PK00.HAC) 6
Multi-AC Power Kit (PK00.MAC) 7

6M965652 Rev. 1.9 (3/19)
Fig. 2
2
3 1
Fig. 2a
16 6
9
810
2
PLUG INTO
WALL OUTLET
7
Fig. 2c
BLACK & WHITE
POWER
CONNECTIONS
10' EXTENSION
13
12
10b
15
14
10a
7
2
2
Fig. 2b
6
9
FROM ELECTRICAL BOX
WITH POWER SUPPLY
16
B
AC VERSION; Fig. 2
• PLUG-IN
•HARDWARE
Note: For AC installation, make power supply connection
before mounting CONTROL BOX (3) to wall.
1. Remove CONTROL BOX COVER (1). Feed the
CABLES (2) from the Faucet through the top of
ENCLOSURE (3).
FOR AC PLUG-IN ONLY
2a. Insert POWER CORD (8) through POWER SUPPLY
GROMMET (9).Fig. 2a.
3a. Insert POWER CORD (8) through side GROMMET (6)
as shown. Fig. 2a.
4a. Connect one of the CABLES (2) to SOLENOID CABLE (7
and the other to the SINGLE AC ADAPTER (10). Connect
POWER CORD (8) to Single AC Adapter (10) and install
CONNECTOR LOCKING DEVICE (16). Fig. 2a.
5a. Mount CONTROL BOX to wall. Replace CONTROL BOX
COVER (1). Tighten cover screws rmly.
6a. Plug AC POWER SUPPLY into wall outlet.
FOR HARDWIRE HOOK-UP ONLY
2b. Insert one end of the 10' EXTENSION (10a) through
POWER SUPPLY GROMMET (9). Fig. 2b.
3b. Insert 10' EXTENSION (10a) through side
GROMMET (6) as shown. Fig. 2b.
4b. Connect CABLES (2) to SOLENOID CABLE (7) and the
other to the 10' EXTENSION CABLE (10a). Install
CONNECTOR LOCKING DEVICE (16). Fig. 2b.
Contractor to supply ELECTRICAL BOX (12) and power
to POWER SUPPLY (13).
5b. Mount POWER SUPPLY (13) onto ELECTRICAL
BOX (12). Connect connections to POWER SUPPLY
CONNECTIONS (14). Fig. 2c.
6b. Connect the10' EXTENSION (10b) to the POWER
SUPPLY CABLE (15). Fig. 2c.
CAUTION Disconnect AC power supply
before opening CONTOL BOX.
CAUTION: Use only American Standard supplied cable sets.
Using non-AS supplied cables, or cutting, splicing or modifying
any components will void the warranty.

7M965652 Rev. 1.9 (3/19)
CMULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a
Important: All control box covers must be removed before beginning to make daisy-chain connections.
Disconnect the rst unit’s Y-Adapter from power supply before making daisy-chain connections.
Note: For Unit #1 electrical instructions, refer to section B (page 5).
For subsequent Units, refer to instructions below...
1. Remove COVERS from all CONTROL BOX (3).
2. Insert pervious unit’s 10’ EXTENSION (11a) through
gray GROMMET (5b) and connect to single terminal of
Y-ADAPTER (11).
3. Remove solid black plug grommet from left side of all
CONTROL BOX (3), and replace with GRAY
GROMMET (5b). (Supplied with each Faucet).
4. Feed CABLES (2) through the top of CONTROL BOX (3).
Connect one CABLE (2) to the SOLENOID CABLE (7),
and the other to either of the two available terminals of
the Y-ADAPTER (11). Connect the current unit’s 10'
EXTENSION (10a) to available terminal of the
Y-ADAPTER (11).
5. Feed the other end of the 10 ft. EXTENSION (10b)
through the two GRAY GROMMETS (6a and 6b) and
connect to the single terminal of the next unit’s
Y-ADAPTER (11). Place Y-ADAPTER (11) into
CONTROL BOXT (3).
6. Repeat Steps above for each additional Unit, for a
Max. of 15 Units on one AC POWER SUPPLY.
7. Reinstall CONTROL BOX COVERS. Tighten cover
screws rmly.
CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or
modifying any components will void the warranty.
Unit #2 Detail
Fig. 3a
5
5b
10b
6a
6b
10a
7
2
2
11
11a
3
Unit #2 Unit #3
Fig. 3
10 ft.
EXTENSION
CABLE
AC POWER
SUPPLY
*MAXIMUM OF 15 UNITS PER AC POWER SUPPLY.
10' MAXIMUM CABLE LENGTH BETWEEN UNITS.
OR
Unit #1
Already installed
BLACK &
WHITE
POWER
CONNECTIONS

8M965652 Rev. 1.9 (3/19)
AHAND WASH SENSOR OPERATION; Fig. 1
When the Sensor detects a user, the water immediately starts
to ow. Water ow will stop 2 seconds after user is out of
sensor range. The off delay allows the user to comfortably
move his hands without the ow cycling on and off. As a
precaution, a safety timer will turn off the water after the
sensor has been blocked for 59 seconds. The water will stay
off until the blockage is removed from the detection zone.
Detection Zone: 2" - 10" (50mm - 250mm)
Default: Set at Factory 6" (150mm)
BCHANGE SENSOR RANGE;
(Factory set at 6") Fig. 2, 2a
1. Remove CONTROL BOX. Disconnect Power Supply (1),
then reconnect. Fig. 2.
2. While the SENSOR CONTROL LED (2) is blinking slowly,
place your hand 1 - 2 in. (30-50mm) in front of the sensor.
Fig. 2a.
3. When the LED stops blinking and stays “ON”, move your
hand to the desired position and hold in place until the LED
begins to blink again. Fig. 2a.
4. Once the SENSOR CONTROL LED (2) begins to blink
again, remove your hand from the detection zone. When the
ashing stops, the detection distance is set.
5. Reinstall CONTROL BOX COVERS (2). Tighten cover
screws rmly.
CCLEAN FILTER ASSEMBLY; Fig. 3
1. Remove CONTROL BOX COVER.
2. Close SUPPLY STOP (13) with 4mm Hex wrench.
Note: Activate sensor to keep water owing out of
faucet while shutting off.
3. Unthread FILTER ASSEMBLY (6) using a 7/16"socket.
4. Pull out the FILTER ASSEMBLY (6), remove and clean
white debris cup and lter screen.
5. Install the FILTER ASSEMBLY (6) back in its place and
tighten with a 7/16"socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with 4mm Hex wrench.
7. Reinstall CONTROL BOX COVER. Tighten cover
screws rmly.
Fig 1
5
6
4
10
3
DETECTION
ZONE
Fig. 2
1
Fig. 2a 1" - 2" (30mm - 50mm)
BLINKING LED
UP TO 10" (250mm)
BLINKING
LED
2
2
6
WHITE
DEBRIS
CUP
FILTER
SCREEN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 3
7/16" SOCKET
4mm HEX WRENCH
13
CAUTION Before opening CONTROL BOX
disconnect AC power supply.
MAINTENANCE

9M965652 Rev. 1.9 (3/19)
Fig. 4
CR-P2
6
3
2
STANDARD
BATTERY
PWRX
4
1
5
2
3
Fig.5
1
Fig.5
DINSTALL / REPLACE THE BATTERY
or PWRX; Fig. 4
1. Remove COVER from CONTROL BOX (1).
2. Disconnect BATTERY HOLDER (3) from CABLE (5).
3. Remove old BATTERY from Battery Holder (3). Install new
BATTERY (2) making sure the terminal side is inserted rst
and shape of the battery follows the shape of the BATTERY
HOLDER (3).
4. To replace PWRX BATTERY PACK (4), unplug and replace
with new Power Pack.
5. Reconnect BATTERY HOLDER (3) to CABLE (5).
6. Reinstall CONTROL BOXT COVER. Tighten cover
screws rmly.
E
CLEAN AND REMOVE THE AERATOR; Fig. 5
1. Remove AERATOR HOUSING (1) with KEY supplied
with faucet.
2. Remove AERATOR (2) from HOUSING (1).
3. Clean the AERATOR SCREENS (3).
4. Clean with water. Reassemble and install into spout end.
Make sure black seal washer is in place..

10 M965652 Rev. 1.9 (3/19)
Fig.6
FGENERAL CLEANING; Fig. 5
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Avoid using anything that may scratch the spout surface.
Never use polishing power, detergent or a nylon scrub brush.
They will damage the surface of the spout or Sensor.
CAUTION Do not scratch the sensor when cleaning. Avoid using
any abrasives or harsh detergents or chemicals.
FAQ’S
Q: How will I know if the battery needs to be replaced?
A: Valve will not open and sensor will continuously blink 2 times interrupted by a pause, for up to 7 days.
Q: Why has the ow rate of the faucet reduced signicantly?
A: The lter assembly, ow regulator or areator/spray may be clogged. Check and clean. Refer to
Start-up/Maintenance, sections C, D and E.
Q: Why doesn’t water ow out of faucet when I’m within the sensor detection zone?
A: Battery may need replacement. If sensor continuously blinks 2 times interrupted by pause, replace battery
or call (844) CRT-TEAM / [phone].Z
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging from 20-80 psi.