American Standard SERIN T064.342 User manual

Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
SERIN™
Wall Mount Electronic
Proximity Lavatory Faucet
Certified to comply with ASME A112.18.1
© 2014 American Standard
To learn more about American Standard Faucets visit our website at:
www.americanstandard.com or U.S. customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call [phone] (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
M965613
Product No.'s & Options
Specications
Faucet Installation
Electrical Installation
Start-up / Maintenance
FAQ’s / Troubleshooting
Replacement Parts
1
2
2-5
6-8
9-10
10-11
12
T064.342
T064.353
T064.362
T064.372
T064.392
T064.345
T064.355
T064.365
T064.375
T064.395
MODEL NUMBERS
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
NOTE: Please refer to R350 Mounting Kit
installation instructions #M965614 prior to
faucet installation.

1
7a. DC Long Life Power Pack (for .342, .345)
7b. DC Standard Battery (for .353, .355)
7c. AC Power Supply (for .362, 365)
7d. AC Power Transfomer (.392, .395)
8. Y-Connector
9. 10 ft. Extension
10. Mixing Valve (optional, must be ordered separately)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
How to order the Serin™ Proximity Product The R350 Mounting Kit is a
required component that
must be purchased separately.
1. Choose Power Supply 2. Choose Desired Flow Rate • Hot and Cold Inlets
Mixing Valve (optional)
1. Remove the fitting and loose items from the carton.The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
605XTMV1070 R350 MOUNTING KIT
(Must have R350 Mounting Kit
installed prior to Wall Mount
faucet installation)
PRODUCT No.s
2
4
1
10
56
Mixing ValveBase Product
Spout
M965613
All T064. SERIES
T064.353
T064.355
T064.362
T064.365
T064.392
T064.395
T064.372
T064.375
3
8
7d
8
99
7c
7a
7b
1. Installation Instructions
2. Spout Assembly
3. Elbow Kit
4. Mounting Kit
5. Supply Hose
6. Electrical Enclosure
DC Long Life
Power Pack
T064.342
T064.345
DC Standard
Battery
AC Plug-in AC Hardwire AC Multi
Installation Instructions
Installation Instructions
(InToronto Area only: 1-905-3061093)
SERIN™
Wall Mount Electronic
Proximity Lavatory Faucet
Certified to comply with ASME A112.18.1M
© 2014American Standard
Tolearn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: [email protected]
For Parts, Service,Warranty or other Assistance,
please call [phone] (In Canada: 1-800-387-0369)
NOTETO INSTALLER: Please give this manual to the customerafter installation.
(InToronto Area only: 1-905-3061093)
M965612
T064.342
T064.352
T064.362
T064.372
T064.392
T064.345
T064.355
T064.365
T064.375
T064.395
MODEL NUMBERS
CAUTION: Use only American Standard
supplied cable sets.Using non-AS supplied
cables, or cutting,splicing or modifying any
components will void the warranty.
Product No.'s& Options
Specications
How to Install
Electrical Hook-up
Maintenance
FAQ,s/ Troublingshooting
Replacement Parts
1
2
2-5
6-8
9-10
10-11
12

RECOMMENDED TOOLS
1Slip Jaw Pliers
2Adjustable Wrench
3Plumbers' Putty or Caulking
4Phillips Screwdriver
5Flat Blade Screwdriver
6Electric Drill & 1/4"
Drill Bit
7Tape Measure
1
2
1
2
3
4
5
6
7
10'
SPOUT ASSEMBLY INSTALLATION;
Fig. 1
FAUCET INSTALLATION
CAUTION Turn off hot and cold water
supplies before beginning
1
1. Remove both MOUNTING SCREWS (1), then
remove upper PLASTIC GUARD (2). Remove the
CORD HOLDER (3a) and CABLE HOLDER (4a)
from the PLASTER GUARD (2).
IMPORTANT: Secure the CORD HOLDER (3a)
and the CABLE HOLDER (4a) from falling back
through the hole in the wall.
2. Remove the two EXTENSION CABLE ENDS (5a)
from the CABLE HOLDER (4a).
IMPORTANT: Secure the CORD HOLDER (3a)
and the EXTENSION CABLES (5a) from falling
back through the hole in the wall.
3. Remove the CORD HOLDER (3b) and CABLE
HOLDER (4b) from the two bottom PLASTER
GUARDS (6).Use a flat blade screwdriver to break
off the two ends of the lower PLASTER GUARDS
(6) flush with the finished wall.
IMPORTANT: Be carefull not to damage the wire
cables. Secure the CORD HOLDER (3b) and the
CABLE HOLDER (4b) from falling back through
the holes in the wall. Remove the two EXTENSION
CABLE ENDS (5b) from the CABLE HOLDER (4b).
M965613
Fig. 1
2
3/8" COMP.
*ELECTRICAL
BOX
(supplied by others)
Roughing-in Dimensions GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal
resistant solid brass construction single post
mounting. Operates on DC (battery/power pack) or
AC permanent power (plug-in/hardwire). In-line
strainer for solenoid is integral. Single inlet 3/8
compression, built-in checks, and flexible stainless
steel 16-1/4" reach inlet hose for spout connection.
Note: All plumbing and electrical wiring must be
installed in accordance with applicable codes,
regulations and standards.
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
*RECOMENDED ELECTRICAL BOX OR
EQUIVALENT BY OTHERS
ELECTRICAL BOX IS ONLY REQUIRED FOR
HARD-WIRED AC INSTALLATIONS (.392 & .395)
4" (102mm) SQ. X 3-1/2" (89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY CONTRACTOR).
102 - 203mm Recommended
(4" - 8" Recommended)
70mm (2-3/4) DIA.
FINISHED FLOOR
81mm
(3-3/16)
150mm - 225mm
MIN. (5-7/8) - MAX. 8-7/8
FINISHED WALL
29-1/2" MAX.
(750mm)
6
5b
5b
4b
3a
3b
6
5a
5a
4a

INSTALL SPOUT MOUNTING KIT;
Fig. 2
1a
M965613
Fig. 2
Fig. 3
Fig. 4
1. Make sure that SEAL (7) is installed into the groove
on the back of the MOUNTING FLANGE (8). Feed
the CORD HOLDER (3a) and the EXTENSION
CABLES (5a) through the MOUNTING FLANGE (8).
2. Install the MOUNTING FLANGE (8) to the wall with
three SCREWS (9) that thread into the MOUNTING
PLATE (10) within the wall. DO NOT fully tighten
the SCREWS (9). HAND TIGHTEN ONLY.
1. Slide SPOUT ESCUTCHEON (11) onto SPOUT (12).
2. Slide COMPRESSION RING (13) and
COMPRESSION SEAL (14) onto SPOUT (12).
3. Connect SPOUT HOSE (15) onto CORD HOLDER (3a)
by pressing until secure connection is achieved .
INSTALL SPOUT ASSEMBLY;
Fig. 3
1b
1. Connect the FAUCET SENSOR CONNECTORS (16)
to the EXTENSION CABLES (5a), and secure the
connections by installing into CONNECTOR HOUSINGS
(17) as shown. Rotate the END CAPS (18) to secure the
connection within the CONNECTOR HOUSINGS (17).
2. Pull the bottom end of EXTENSION CABLES (5b)
so that the CONNECTOR HOUSINGS (17) are inside
the wall.
4. Pull bottom CORD HOLDER (3b) and fish SPOUT
HOSE (15) through the wall and out through the
bottom wall opening (19).
5. Cut the CORD HOLDER (3a) off the end of the
SPOUT HOSE (15) as shown.
IMPORTANT: Secure the SPOUT HOSE (15) from
falling back through the wall opening (19).
SECURE WIRE CONNECTIONS;
Fig. 4
1c
3
7
10
8
3a
9
5a
3b
3a
15
17
16
19
17
18
18
5a
5b
11
15
3a
13
14
12
CUT SPOUT
HOSE

M965613
Fig. 5
ALIGN SPOUT ASSEMBLY;
Fig. 5
4
12
8
12
11
13 20
21
1d
1. Align and push SPOUT (12) through hole, loosely
installed MOUNTING FLANGE (8) and MOUNTING
PLATE (10).
2. Once MOUNTING FLANGE (8) is aligned with
MOUNTING PLATE (10) opening, tighten the three
MOUNTING FLANGE SCREWS (9). (Tighten each
screw little by little to avoid missalignment!)
3. Align and slide and COMPRESSION SEAL (14) and
COMPRESSION RING (13) to MOUNTING FLANGE (8).
1. Once MOUNTING FLANGE (8) is installed, move the
SPOUT (12) in or out to determine desired spout length
from finished wall. Note:The Min. is 150mm, (5-7/8)
and the Max. is 225mm, (8-7/8) from the finished wall
to center of the spout end.
2. Tighten COMPRESSION RING (13) to MOUNTING
FLANGE (8) by tightening the three COMPRESSION
RING SCREWS (20) with HEX WRENCH (21) supplied.
This will fix SPOUT (12) length from finished wall.
3. Push ESCUTCHEON (11) to MOUNTING FLANGE (8)
and hand tighten to complete spout installation.
150mm - 225mm
MIN. (5-7/8) - MAX. 8-7/8
Fig. 6
SPOUT LENGTH
150mm - 225mm
MIN. (5-7/8) - MAX. 8-7/8
12
13
14
8
13
14
10
10
9
9
SECURE SPOUT ASSEMBLY;
Fig. 6
1e
8

M965613
5
INSTALL SUPPLY ELBOW
ASSEMBLY & ENCLOSURE;
Fig. 7 and Fig. 7a
1. Install HOSE CLAMP (22) onto SPOUT HOSE (15).
Install SPOUT HOSE (15) onto ELBOW NIPPLE (23).
Fully tighten HOSE CLAMP (22) to secure SPOUT
HOSE (15) to ELBOW ASSEMBLY (24). Fig. 7.
2. Using the ANCHORS (25) and SCREWS (26) supplied,
attach ELBOW ASSEMBLY (24) to finished wall, covering
the hole in wall. Fig. 7.
3. Remove ENCLOSURE COVER (27). Feed EXTENSION
CABLES (5b) THROUGH GROMMET (28) in back of
ENCLOSURE (29). (Refer to VIEW“A”). Hold the
ENCLOSURE (29) so that it covers the wall opening and
mark the four mounting hole locations as shown. Fig. 7a.
4. It is recommended that the ENCLOSURE (29) be secured
to a wall stud or cross brace within the wall using the
SCREWS (30) supplied. If the ENCLOSURE (29) is to be
installed on tile or plaster walls, the ANCHORS (31) and
SCREWS (30) should be used.
2
22
25
26
27
29
31
30
28
24
15
23
Fig. 7
Fig. 7a
5b
VIEW “A”
VIEW “A”
32
35
33
34
24
29
Fig. 8
LAVATORY RIM OR
MOUNTING SURFACE
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 8
3
1. Connect G 1/2˝ end of SUPPLY HOSE (32) to the
ELBOW ASSEMBLY (24). Tighten with adjustable
wrench to make a water tight connection.
2. Connect G 3/8˝ end of SUPPLY HOSE (32) to nipple
on top of ENCLOSURE (29). Tighten with adjustable
wrench to make a water tight connection.
3. IMPORTANT: INSERT FIBER WASHER (33)
INTO SUPPLY NUT (34) ON ENCLOSURE (29).
4. Connect FLEXIBLE SUPPLY (35) to bottom SUPPLY
NUT (34). Connect other end directly to wall supply.
Connection is G 3/8" compression.
Note: FLEXIBLE SUPPLY (35) measures 20" from the
bottom of the ENCLOSURE (29) base. If additional
supply length is required, installer must purchase parts
separately. If FLEXIBLE SUPPLY (35) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
ELECTRICAL BOX
FOR HARDWIRE
INSTALLATION
(supplied by others)
9" TO 12"
(229mm TO 305mm)

M965613
6
1. Remove ENCLOSURE COVER (1) from
ENCLOSURE (2). Fig. 1.
2. Feed the EXTENSION CABLE (3) from the Faucet
through SIDE GROMMET (4). Fig. 1a.
3. Connect SOLENOID CABLE (5) to EXTENSION
CABLE (3) from the Faucet. Fig. 1a.
4. Insert BATTERY (6) into BATTERY HOLDER (7),
make sure the shape of the BATTERY (6) follows the
shape of the BATTERY HOLDER (7) and terminal
end is inserted first. Fig. 1b.
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is
self adjusting. Keep detection zone clear for 15
seconds after power is connected.
5. Connect the BATTERY CONNECTOR (7a) from the
Standard or Long Life Power Pack to EXTENSION
CABLE (8) as shown. Fig. 1c. Place Standard
Battery or Long Life Power Pack into Housing.
Fig. 1d.
6. Replace ENCLOSURE COVER (1). Tighten cover
screws firmly.
LONG LIFE POWER PACK
& STANDARD BATTERY; Fig. 1
Product Page
DC Long Life Power Pack
T064.342 / T064.345 6
DC Standard Battery
T064.353 / T064.355 6
AC Plug-in
T064.362 / T064.365) 7
AC Hardwire
T064.392 / T064.395) 7
AC Multi Hook-up
T064.372 / T064.375) 8
A
ELECTRICAL INSTALLATION
CAUTION: Use only American Standard supplied
cable sets. Using non-AS supplied cables, or
cutting, splicing or modifying any components will
void the warranty.
!
Fig. 1a Fig. 1b
Fig. 1
Fig. 1c
5
5
Fig. 1d
3
2
1
6
7
INSTALL BATTERY
STANDARD
BATTERY
STANDARD
BATTERY
LONG LIFE
POWER PACK
CR-P2
7a
7a
8
4
LONG LIFE
POWER PACK

M965613
7
Fig. 2
Fig. 2a
Fig. 3
Fig. 3a
BLACK & WHITE
POWER
CONNECTIONS
16
12 CONNECTOR NOT
USED IN THIS
INSTALLATION
12
10
11b
15
4" ELECTRICAL BOX
OR EQUIVALENT BY
OTHERS
14
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
AC POWER
SUPPLY
2
1
3
5
4
10
AC POWER
SUPPLY
9
8
AC VERSIONS (HARDWIRE / PLUG-IN);
Fig. 2 and Fig. 3
B
CAUTION Before opening ENCLOSURE
disconnect AC power supply.
1. Remove ENCLOSURE COVER (1) from ENCLOSURE (2). Fig. 2.
2. Feed the EXTENSION CABLE (3) from the faucet through
GROMMET (4). Then connect the SOLENOID CABLE (5) to
EXTENSION CABLE (3).Fig. 2a.
3. Insert POWER CORD (9) through OUTER GROMMET (10)
as shown. Fig. 2a.
4. Connect POWER CORD (9) to EXTENSION CABLE (8)
from faucet sensor. Replace ENCLOSURE COVER (1).
Tighten cover screws firmly.
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is
self adjusting. Keep detection zone clear for 15
seconds after power is connected.
5. Plug AC POWER SUPPLY into wall outlet. Fig. 2a.
FOR HARDWIRE HOOKUP ONLY; Fig. 3
6. Insert 10 ft. EXTENTION (11a) from HARD WIRE POWER
SUPPLY (12) into ENCLOSURE through OUTER GROMMET
(10) and side GROMMET (4). Connect 10' Extension (11a) to
single terminal of Y-ADAPTER (13). Fig. 3.
7. Insert EXTENSION CABLE (8) from faucet through
GROMMET (4a) and connect to either of the two terminals at
the one end of the Y-ADAPTER (13). Replace ENCLOSURE
COVER (1). Tighten cover screws firmly. Fig. 3.
Contractor to supply ELECTRICAL BOX (14) and power to
POWER SUPPLY (12). Fig. 3a.
8. Connect White and Black connections to POWER SUPPLY
CONNECTIONS (15). Fig. 3a.
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is
self adjusting. Keep detection zone clear for 15
seconds after power is connected.
9. Connect the 10 ft. EXTENSION (11b) to the POWER SUPPLY
CABLE (16). Mount POWER SUPPLY (12) into ELECTRICAL
BOX (14).
FOR PLUG-IN HOOKUP ONLY; Fig. 2
11a
13
7
3
8
4
4a
!
!

M965613
8
Fig. 4
Fig. 4a
Unit #1 Unit #2 Unit #3
AC POWER
SUPPLY
O
R
*MAXIMUM OF 15 UNITS PER AC POWER SUPPLY.
10' MAXIMUM CABLE LENGTH BETWEEN UNITS.
4"(102mm) SQ. X 3-1/2"(89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
10 ft. EXTENSION
CABLE
10 ft. EXTENSION
CABLE
FOR AC-VERSION
(MULTI HOOK-UP); Fig. 4 and Fig. 4a
C
Unit #1 Detail
AC POWER
17
3
13
18
11b
5
4
4a
8
11a
1. Remove COVERS from all ENCLOSURES (2).
Fig. 4 and Fig. 4a.
2. Remove SOLID BLACK PLUG GROMMET (17) from
left side of all ENCLOSURES (2).Replace with GRAY
GROMMET (18). (Supplied with each Faucet).
Fig. 4 and Fig. 4a.
3. Feed the EXTENSION CABLE (3) from the Faucet
through GROMMET (4) and connect it to the
SOLENOID CABLE (5). Fig. 4 and Fig. 4a.
4. Feed the EXTENSION CABLE (8) from the Faucet
through GROMMET (4a) and connect to either of the
two terminals at the one end of the Y-ADAPTER (13).
Connect the 10 ft. EXTENSION (11a) to the other
terminal at the same end of the Y-ADAPTER (13).
Fig. 4 and Fig. 4a.
5. Feed the other end of the 10 ft.EXTENSION (11b)
through the two GRAY GROMMETS (4a and 4b) and
connect to the single terminal end of the next unit’s
Y-ADAPTER (13). Place Y-ADAPTER (13) into
ENCLOSURE (2) as shown in Fig. 4 and Fig. 4a.
6. Repeat Steps above for each additional Unit, for a
Max. of 15 Units on one AC POWER SUPPLY.
7. Replace ENCLOSURE COVERS. Tighten cover
screws firmly.
YOU CAN USE EITHER THE PLUG-IN
OR HARD-WIRED TRANSFORMER.
YOU CAN USE EITHER THE PLUG-IN
OR HARD-WIRED TRANSFORMER.
4b
2
OR

M965613
9
Fig. 2
Fig. 1
DETECTION
ZONE:
BETWEEN
SPOUT AND
BASE OF SINK
Fig.3
K
CR-P2
3
6
4
5
2
1
STANDARD
BATTERY
7/16" SOCKET
WHITE
DEBRIS
CUP
FILTER
SCREEN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. Remove COVER from ENCLOSURE (1).
2. Disconnect BATTERY HOLDER (3) from SENSOR
CABLE (5).
3. Remove old BATTERY from BATTERY HOLDER (3).
Install new BATTERY (2) making sure the terminal side
is inserted first and shape of the battery follows the
shape of the BATTERY HOLDER (3).
4. To change LONG LIFE POWER PACK (4), unplug and
replace with new Power Pack.
5. Reconnect BATTERY HOLDER (3) to SENSOR
CABLE (5).
6. Replace ENCLOSURE COVER. Tighten cover screws
firmly.
HOW TO INSTALL AND CHANGE
BATTERY; Fig. 2
B
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (13) with 4mm Hex wrench.
Note: Activate sensor to keep water flowing out of
faucet while shutting off.
3. Unthread FILTER ASSEMBLY (6) using a 7/16" socket.
4. Pull out the FILTER ASSEMBLY (6), remove and clean
white debris cup and filter screen.
5. Install the FILTER ASSEMBLY (6) back in its place and
tighten with a 7/16" socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with 4mm Hex wrench.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
HOW TO CLEAN FILTER
ASSEMBLY; Fig. 3
C
CAUTION Before opening ENCLOSURE
disconnect AC power supply.
START-UP / MAINTENANCE
When the Sensor detects a user, the water immediately
starts to flow. Water flow will stop 1.5 seconds after user
is out of sensor range. This comfort timer allows the user
to move his hands without the flow cycling on and off. As
a precaution, a safety timer will turn off the water after
the sensor has been blocked for 55 seconds. Water flow
will resume when the blockage is removed from the
detection zone and the sensor is activated again.
HAND WASH SENSOR OPERATION;
Fig. 1
A
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is
self adjusting. Keep detection zone clear for 15
seconds after power is connected.
!
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is
self adjusting. Keep detection zone clear for 15
seconds after power is connected.
!
6
13